Product

FieldFox C Handheld Microwave Spectrum Analyzer, 10 GHz

N9935C

Spectrum Analyzer

Keysight Technologies

N9935C - Keysight Technologies

Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth.Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup.Perform over-the-air measurements for 5G NR and LTE.Use GPS/GNSS for geolocation and timestamping.Carry one lightweight unit at 3.4 kg (7.4 lb).What's included:Base model: spectrum analyzer (SA)AC/DC adapterLocalized power cordRechargeable Li-ion batterySoft carrying case with backpack and shoulder straps

Product

C Series Counter Input Module

Input/Output Module

NI

NI

The C Series Counter Input Module features flexible, 32-bit counters. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal, switchable pull-up resistor. Additionally, you can use the C Series Counter Input Module to perform encoder position and velocity measurements as well as to synchronize the counters with other analog, digital, and counter measurements in your chassis.The C Series Counter Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.

Product

Thermocouple Contact, Receiver, Constantan, Type T (°C)

610113148

Thermocouple Contact (Receiver)

Virginia Panel Corporation

610113148 - Virginia Panel Corporation

Primary mating contact 610113149.

Product

*C Series CAN Interface Module

CAN Interface

NI

NI

C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.

Product

Thermocouple Contact, ITA, Copper, Type T (°C)

610113169

Thermocouple Contact (ITA)

Virginia Panel Corporation

610113169 - Virginia Panel Corporation

Primary mating contact 610113168.

Product

NI-9475, 60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module

780132-02

Digital Module

NI

780132-02 - NI

60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9475 works with a variety of industrial devices such as solenoids, motors, actuators, relays, and lamps. Each channel sources up to 1 A at levels up to 60 VDC and features isolation from … channel‑to‑earth ground.

Product

cRIO-9048, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller

785619-01

Embedded Controller

NI

785619-01 - NI

1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller - The cRIO-9048 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.

Product

NI-9426, 24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module

780030-01

Digital Module

NI

780030-01 - NI

24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module - The NI‑9426 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels.

Product

NI-9425, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module

785044-01

Digital Module

NI

785044-01 - NI

24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.

Product

NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module

779009-01

Digital Module

NI

779009-01 - NI

24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.

Product

sbRIO-9403, Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module

780539-01

Digital Module

NI

780539-01 - NI

Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The sbRIO‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9403 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and other applications.

Product

NI-9219, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module

785994-01

Analog Input Module

NI

785994-01 - NI

100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.

Product

NI-9861, 1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module

781962-01

CAN Interface

NI

781962-01 - NI

1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI‑9861 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The NI‑9861 is ideal for applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.

Product

Chromel, Type K (°C), Thermocouple Contacts

Thermocouple Contact (ITA)

Virginia Panel Corporation

Virginia Panel Corporation

Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.