Electrical Installation
-
Product
PXI/cPCI Modular Embedded Controller - PXI 2.0/PCIe 3.0 Compatible, Max 512MB DRAM (256MB Installed)
TE9500-1200
-
TSI's modular approach to PXI embedded controllers provides maximum flexibility and upgradeability for most, if not all, PXI embedded controller requirements. The TE9500 series of embedded controllers is based on the industry standard ETX (embedded technology extended) SOM (system-on-module) form factor. Whether you choose a power saving Celeron CPU or a high performance mobile Pentium III, the TE9500ís integrated interfaces and upgradeable options apply across all models of the TE9500 series of controllers. The TE9500 series gives you the ability to control your controller.
-
Product
Electrical Tester
T+Pro
-
Safer than solenoid testers and fully compliant with NFPA 70E, (when used properly per Article 110.4 Use of Equipment (A) Test Instruments and Equipment), the T+Pro helps electricians and technicians work safer by indicating the presence of voltage, even when the batteries are dead.
-
Product
Digital Battery & Electrical System Analyzer w/Printer
726
-
*Accurate Battery & Electrical System Tester *Features programmed test for new Start/Stop Batteries 3 Testers in ONE! 1) 6 & 12 Volt Battery Tester + 12V Start/Stop Battery Test 2) 12 & 24 Volt Charging System Tester 3) Alternator-Starting-Charging System Tester *Wide Testing Range from 40 to 2,000 CCA *Built-in Printer - print the results for permanent service records *Removable/Replaceable Cable Set *Patented Dynamic Resistance Technology
-
Product
ELECTRICAL TEST Kit
1021 TK
-
Standard Electric Works Co., Ltd
2950 CL ● Pocket size.● 4000 counts.● Full automatic measurement : Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (auto off in 1 minute). ALS-2 ● Use with any clamp meter.● x10 mode allows for more accurate measurements of low amperage devices.● x1 mode allows for direct reading.● 4mm voltmeter input jacks.● Integrated ground conductor.● 10 amp capacity.● 10cm plug cord for greater flexibility.
-
Product
Electrical Safety Tester
GSC60
-
One instrument for all electrical safety tests and Power Quality analysisGSC60 was designed with the aim of making safety of electrical installations visible and valuable, easily and quickly.
-
Product
Electrical Receiver Conformance Test Application for IEEE 802.3bs/ cd
M8091BSCA
-
IEEE 802.3bs receiver test application for 200GAUI-4 and 400GAUI-8, covering chip-to-module, chip-to-chip, backplane, and copper cable interconnects.
-
Product
Electrical Networks Control System
-
Electrical networks control system is intended for measurements of network electrical resistance and insulation electrical resistance of the tested specimen. The measurement process takes a couple of minutes.
-
Product
Electric Servo Motor Type 2 · 4 Poster Vibration Tester
-
It arranges four 3-axis vibration testers equipped with a high torque, ultra-low inertia servomotor to test the vibration of the finished vehicle.
-
Product
Electric Motor Test Systems
-
Electric Motor Test Systems feature our highly successful water brake dynamometer which is used as an electric motor loading device.
-
Product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
-
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
Product
Portable Electrical Management Systems
EMS-LCHW30
-
Progressive Industries Portable Electrical Management Systems (EMS) provide full RV protection against all adverse power conditions. You will feel secure with multi-mode surge, voltage, polarity and lost/open neutral protection. Each unit includes a digital display, scrolling continuously through the power source information: Voltage(s), current, frequency, error code, and previous error code (if applicable). Replacement parts are simply plug-and-play, making repairs quick and easy. As with our portable models, the computer is driven by state of the art microprocessors. Should the software ever change, EMS owners can receive a free upgrade at no cost.
-
Product
Electric Vehicle
-
Chroma Systems Solutions, Inc.
EV Automotive and Battery Test Advancements
-
Product
Electric Servo Motor Type Power Circulation Type Rotary Torquer Tester
-
Tests For Clutches Durability, Torque Converters, Transmissions, Differential Gears, CVJs, Etc. Can Be Performed At Low Cost By The Load Using The Power Circulation System.
-
Product
Electrical Test Tool
-
Beijing GFUVE Electronics Co.,Ltd.
Electrical testers are useful to check for voltage, continuity, shorted or open circuits, and improper wiring.
-
Product
Eddy Current Electric Conductivity Meter
-
Measures the conductivity of a solution by measuring the alternating magnetic field generated by the solution.
-
Product
Electric Servomotor Large Table Vibration Tester
-
Large Table Vibration A Tester Equipped With An Electric Servomotor Actuator. Seismic Simulation Also Supports Large-Amplitude Long-Period Vibration Tests. It Can Accurately Reproduce The Vibration Given To The Ground And Buildings Due To The Earthquake.
-
Product
Automatic Production Tester for Electric Motor Stators
MTC 3
-
The fully automatic MTC3 stator testers test your windings reliably and quickly for possible insulation faults via our patented surge voltage test.After connecting the test object completely the test is performed with an automatic switching of the connections and the test methods. The MTC3 evaluates each test step. At the end of the complete test process it provides a clear and reproducible GO or NO GO-statement.
-
Product
Programmable Electrical Rule Checking tool
Calibre PERC
-
Calibre® PERC™, Mentor Graphics'' newest reliability verification solution is designed to address your advanced circuit verification needs for electrostatic discharge (ESD), electrical overstress (EOS), signals crossing multiple power domains, advanced ERC and other reliability concerns.
-
Product
Electricity Meters Tester
Caltest 10
-
Calmet Smart Calibration Devices
Single phase portable electricity meters tester class 0.5% powered from tested circuit with load force possibility apart from tested object. There is no need to disconnect the users during measurement
-
Product
Electric Servo Motor Type 2 Axis Switching Simultaneous Vibration Tester
-
It is a 2-axis switching vibration tester and a 2-axis simultaneous vibration tester that mounts an electric servomotor actuator on the vibration drive unit.
-
Product
Electrical measurements
-
Instruments for measurement and analysis in accordance with the regulations of single / triphasic low voltage networks and data networks via cable or fibre.
-
Product
Field-installation Type Electric Conductivity Meter (Four-Wire Transmission, For High-concentration)
HE-200H
-
HE-200H connects conductivity sensor (FES-125F,126F) and measures conductivity and temperature in the sample water. It can be used not only for measurement of electrical conductivity in aqueous solution, but also for concentration adjustment and rinse monitoring of CIP, etc., as well as for concentration monitor of process.
-
Product
Testing Electric Pump Motors
-
This Custom Motor Test System is designed for the testing of 5 different sized electric motors used in various sump, utility, sewage, well, pool and pond pumps. All of the components mentioned above are mounted on a versatile table that can be easily reconfigured and retrofitted to any Magtrol dynamometer.
-
Product
ECPR System (Electrically Calibrated Pyroelectric Radiometer)
Rs-5900
-
Developed in conjunction with NIST, the Rs-5900 ECPR is a ±1% absolute accuracy radiometric transfer standard for the visible to near-IR (0.25-2.0µm), with the RsIR Option extending the ±1% accuracy to >20µm. The RsP-590 Pyroelectric Probe requires no cooling and maintains ±1% accuracy from 1 µW to 100 mW. The ECPR uses an auto-nulling, electrical substitution technique that allows the instrument to be referenced against NIST electrical standards, insuring maximum accuracy and precision. Unlike most electrically calibrated radiometers, there is a direct correlation between electrical and optical heating because the same material serves as both the optical absorber and electrical heating element.
-
Product
Electrical Safety Testers- Hipots
-
Safety testers (also named hi-pot tester/hipot tester/hipot test) are designed to ensure safe operation of DUTs under various operating conditions and environment.GW Instek’s GPT-9900/GPT-9800/9600 series safety testers(hipot test) provide safe and quick measurement tools for AC/DC withstanding voltage tests, insulation resistance tests, and AC ground bond tests. Those tests are required by many international safety regulations such as CE, UL, VDE, and etc. We also have leakage current tester, GLC-9000, which supports all the major leakage current test standards for medical and general electronic equipment.
-
Product
GPIB User Installable Interface Module
E363GPBU
Interface Module
Add a GPIB interface to your E36300 Series triple output or E36200 Series autoranging bench power supply.
-
Product
Digital Electrical Network Analyzer
2126 NA
-
Standard Electric Works Co., Ltd
Microprocessor-controlled. Built-in earth tester. Built-in loop/psc tester. 0.03-2000Ω (software ctrl). Built-in voltmeter. Built-in wiring checker. One push button smart control. Display L-N and L-E voltages. 50 to 280Vac (sine). Display line path impedance. 0.01-2000Ω (software ctrl). Display earth path impedance. 0.01-2000Ω (software ctrl). Display neutral path impedance. 0.01-2000Ω (software ctrl). Display psc line to neutral. 6kA@230Vac supply. Display psc line to earth. 6kA@230Vac supply. Re-scroll through previous results. Bat. ok/low battery indicator. Auto off function. Color-coded test leads. Rugged case. Ultra low power consumption.
-
Product
Octal Small Form Factor Pluggable Electrical Interface
-
Eoptolink Technology Inc., Ltd.
Eoptolink is developing OSFP(Octal Small Form Factor Pluggable) a new pluggable form factor with eight high speed electrical lanes that will initially support 400 Gbps (8x50G or 4x100G). It is slightly wider and deeper than the QSFP but it still supports 32 OSFP ports per 1U front panel, enabling 12.8 Tbps per 1U switch lot. OSFP is designed to support the next generation of 800G optics modules that will use eight lanes of 100Gbps, and offers backwards compatibility with 100G QSFP.
-
Product
Production Test Stands for Electric Motors
-
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
Product
E-DRIV® Electric Screwdrivers
E-Series
-
The electric screwdriver is for light duty tightening applications. The assembly tool plugs directly into a power outlet and does not require a separate power supply unit. Ensures accuracy in fastening with precision automatic shut-off clutch once preset torque is achieved. Operates on a duty cycle of 0.5 seconds on and 3.5 seconds off.
