Patient Simulators
generate known values for any or all of the following medical equipment which measure: invasive blood pressure (IBP), Arrhythmias, Respiration, temperature and Fetal simulation.
-
Product
2 Port T1/E1/PRI ISDN Simulator PCI
SIM-2PRI-PCI
-
The most inexpensive ISDN PRI simulator on the market. Designed in standard PCI card form factor it has two PRI(T1 or E1) ports allowing ISDN PRI equipment to be connected together just as if they were connected through the ISDN network. Simulator card does not require any OS drivers, completely software independent and it take only power from the host computer.
-
Product
MIL-STD-1553 A / B Test And Simulation PC / 104+ Module
PC104p-1553
-
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems*Supports ARINC429 and ARINC 664 operations
-
Product
GNSS Modeling And Simulation
-
CAST Navigation’s GNSS simulation systems produce GNSS RF signals that provide a precise and repeatable testing signal, perfect for use either in the field or in the laboratory environment. These systems can be used for a wide range of testing and integration verification applications and they are an ideal choice for stimulating military or commercial devices where only GNSS signals are needed. Our simulators are powered by proprietary multi-frequency, multi-constellation GNSS RF signal generation technology. This technology provides you with highly accurate and fully programmable signals along with advanced vehicle trajectory capabilities allowing you to custom tailor parameters and trajectories to meet your simulation requirements.
-
Product
MIL-STD-1553 A / B Test And Simulation PMC Module
PMC-1553
PMC Module
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems*Heat sink and / or protective coating available*Optional input / output for front panel
-
Product
2 Port BRI-S/T ISDN Simulator
BRI-2ST
-
The most inexpensive ISDN simulator on the market. The unit has two S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
CAN & LIN bus Custom Test & Simulation Software
CanX
-
Schleissheimer Soft- und Hardwareentwicklung GmbH
CanX is the custom testing and simulation software for CAN and LIN bus for specific user groups. The run-time software is designed to execute predefined or automated tasks in testing, work preparation, production, repair or project management.
-
Product
PXI 16 Channel Switch Simulation Module
40-480-121
Switch Module
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
Simulation Environments Software
Modelica
-
Modelica Libraries with a large set of models are available (overview, details and download). Especially, the open source Modelica Standard Library contains about 1280 model components and 910 functions from many domains.
-
Product
Ring Wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Ring wave interference on electronic line, control line and signal line can be caused by transient due to switch of mains and controlled switch or lightening strike. RWS 600 is designed to conduct immunity test for electronic and electrical device.
-
Product
Non-Hydraulic Steering Module Test Simulator
SMTS
-
The Steering Module Test Simulator (SMTS) from MB Dynamics is a non-hydraulic turnkey lab test system, offering accurate, reliable and repeatable in-laboratory simulations of driver, road & vehicle inputs acting on a steering system, and their associated effects on steering system performance and annoying noises. Supports troubleshooting, identification, diagnosis, and resolution of root causes of unwanted noise and other performance issues common to EPS, EPHS, EPAS, MDPS, and HPS steering systems.
-
Product
PXI RTD Simulator Module, 12 Channel, PT500
40-263-302
Simulator
The 40-263-302 is a 12-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
USB 2.0 SmartCable™ For ARINC429Test And Simulation
ASC429-x
-
USB 2.0 SmartCable™ for ARINC429 Test and Simulation with 6 channels (2Tx/4Rx) and 12 channels (4Tx/8Rx).
-
Product
4 Port T1/E1/PRI ISDN Simulator
SIM-4PRI
-
The most inexpensive ISDN simulator on the market. This unit has four PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Pulse Oximeter Simulators
-
Take control of all your simulations with the next-generation SpO2 pulse oximeter simulator, OxSim Flex. The world’s smallest SpO2 tester now provides complete flexibility in selecting saturation, pulse rate and perfusion index. Users can create customized Preset Simulations for faster testing of oximeter performance and for alarm testing without having to change the monitor’s alarm settings!
-
Product
4 Port Phone Line Simulator (FXS) Adv
SIM-4FXS-A
-
This unit has 4 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
Product
MIMIC® Cable Modem Simulator
-
MIMIC Cable Modem Simulator, is the industry's first integrated simulation tool supporting DOCSIS, allows cable modem developers and cable companies to perform real world, integrated cable and internetworking device simulations. MIMIC allows suppliers of cable modems to design, develop and test their products in a virtual and scalable network environment, assuring customers that their cable modems will work properly when deployed across heterogeneous environments. Cable providers can use MIMIC to simulate the 1000s of households that use cable modems to assure the scalability of cable management software. In addition, providers can also use MIMIC for large-scale Operations Support System (OSS) testing deployments in place of large banks of cable modems, which would be cost prohibitive.
-
Product
Standard Class AAA Solar Simulator
TriSOL TSS
-
Essential for testing virtually any material or product that is exposed to sunlight for long or short periods of time, OAI’s low-cost, Standard Solar Simulators deliver highly collimated, uniform light. Depending on configuration, output on these Solar Simulators is rated at 350W -5,000W.These Class AAA Solar Simulators feature OAI’s Advanced Uniform Beam Optics and are available with a choice of air mass filters to reproduce a wide range of solar spectra. For added flexibility, OAI’s proven lens and collimating mirror technology allows for a variety of exposure area sizes. A Class AAA Solar Simulator is an essential tool for manufacturing as well as R&D; it is indispensable in test labs, industry, and in universities. OAI Standard Solar Simulators are used in photobiology, biomedical, solar cell testing, cosmetic testing, and paints & coatings analysis. Based on 35+ years of proven UV light technology, OAI Solar Simulator Systems deliver repeatable, reliable, constant output, and measurement uniformity.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
-
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Circuit Breaker Simulation Device
PSS01
-
PSS01 is the circuit breaker simulator，which can conduct circuit breaker simulation to test the whole secondary relay scheme together with relay test set. It is very good accessory for protection relay test kit to avoid complicated software programming to finalize the same test.
-
Product
LXI Simulation Tool
60-901-001
-
This tool will simulate all of our PXI & LXI switching products and most of our PXI simulation products allowing for code development independent from your application hardware
-
Product
Troubleshooting Track Circuit Simulators
14900 Series
-
The 14900 seriesTrack Simulator features a front panel with standard set up resistors and terminals and electrically conductive model track to simulate a track circuit suitable for instructional and hands-on training purposes. A locked drawer provides additional switches, potentiometers, and controls that allow selective implementation of many faults commonly found in typical track circuits.
-
Product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P-PLUS | VP 230047
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P-PLUS roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P-PLUS is also suitable for power measurements at constant speed and constant tractive force.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, 1 kV Isolation
41-752A-102
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Environmental Simulation
-
Is your product heat-resistant? Throughout their useful lives, technical products are subject to a multitude of environmental influences, e.g., heat, cold, oscillations or impacts. This influences their functioning and length of service life. We can find out how the effect and cause are interrelated with an environmental simulation. We will test your products under specific environmental conditions and help you to optimize them for sustainable product development.
-
Product
Three-Dimensional Electromagnetic Simulation Package
QuickWave-3D
-
QuickWave 3D (QW-3D), is a universal user-friendly three-dimensional electromagnetic simulation package (winner of the European Information Technology Prize in 1998) based on the conformal FDTD method and supplemented with a range of unique models for curved boundaries, media interfaces, modal excitation, and parameter extraction. Complete 3D electromagnetic simulation offer a set of various results from wide area of applications. A lot of processing/postprocessings present a complete offer of comprehensive solutions from microwave components (filters, couplers, resonators, etc.) through antennas, TDR applications, optimisation and parameters sweep to simulation of microwave heating process (with Basic Heating Module) with temperature dependent media, static, rotated or moved heated object(s), and heat transfer.
-
Product
10 Gigabit Ethernet Test & Simulation Instrument for PXI Express
PXIe-10GE
-
Avionics Interface Technologies
Supports 10G and 1G Full Duplex Ethernet2 Network Interfaces (future expansion to 4 network interfaces)User controlled Ethernet frame transmissions with high precision timing and scheduling
-
Product
AFDX ® / ARINC 664 Test And Simulation PXI Module
PXI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Stard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applicationsWindows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
NIBP Simulator for Testing Patient Monitors
SECULIFE BP PRO
-
The SECULIFE | BPPRO is the high-end product from the new range of NIBP simulators and is distinguished by a great variety of functions. It includes functions such as NIBP, IBP, ECG, temperature, arrhythmia, respiration, leak detection and much more. Specially developed to cover a great diversity of functions and nevertheless to ensure a compact design, the SECULIFE | BPPRO fulfills the requirements of modern medical technology. It makes no compromises with regard to functionality and input diversity. There's hardly another product with a similarly large range of features.
-
Product
MIL-STD-1553 Test & Simulation Instrument for VXI
VXI-1553
-
Avionics Interface Technologies
Dual redundant, multi stream configurations availableSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Real-Time recording and physical bus replayANSI Application interface supporting C, C++, C#, and .NET development - VISA based VXI “Plug & Play’ Device driver provided
-
Product
Simulation Transport Vibration Table
CX-M120
-
Shenzhen Chuangxin Instruments Co., Ltd.
CX-M120 Simulation Transport Vibration Table was applicable to toys,furniture,gifts,cera-mics,packaging and other products to simulate the transport tests.Comply with the U.S. and European transport standards and have characteristic with low noise,reasonable structure,durable,etc.Basic Standard:Following The EN.ANSI.UL.ASTM.ISTA International Trans-port Standard.
