-
Product
Miniature Quartz Force Sensors
-
Often the test engineer will try to take low level measurements with a sensors not rated for these low levels. Due to insufficient sensitivity the resulting data may be noisy, hard to analyze or unusable. Using the appropriately sized and ranged PCB Miniature Quartz Force Sensor solves the problem and gives reliable data at a Low Amplitude level. The miniature sensor configuration permits low-amplitude, dynamic compression, tension, and impact force measurements.
-
Product
RF over Fiber Link TX/RX
L-Band
-
QuestTel''s Satellite L-Band optical fiber Transmitter/Receiver set offers high pefromance and cost effective alternative to conventional coaxial systems. The L-Band Transmitter and Receiver pair is used for transporting L-Band RF over fiber from the antenna to the satellite receiver. Additionally transmitter provides optional 13/18V LNB power as well as Automatic Gain Control (AGC) to manage RF input level. By transporting the L-Band RF over fiber this range can be extended from several hundred feet to over 80 miles. Since optical signal is not affected by electromagnetic field, the quality of your signal will always stay at the high level. Also this fiber solution is more cost effective than coaxial system, as well as more reliable and flexible.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
Test Fixture
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Control Cables
-
TRIUMPH specializes in cable controls which are mechanical connections between controls and actuation systems used in a variety of applications. Our systems provide higher reliability, lighter weight, and greater control box selection. Current controls include wire rope, push-pull controls, sliding friction controls, ball-bearing controls and low-resistance and backlash mechanical control system cables. Wire Rope Controls: Wire Rope is used in applications where weight is critical, and the system operates in tension only. Assemblies are built to your required standards with unlimited configuration capabilities. Sliding Friction Controls: High load capacity in tension and compression. Flexible in any direction, wide temperature range and easy installation. No adjustment or lubrication needed during the life of the control. Ball Bearing Controls: Ball Bearing controls are a self-contained system that performs linear motion under tension or compression loads.Precise and accurate movement with high load capacity offering weight savings, low friction and high efficiency. Quick disconnect ends available.
-
Product
Surge Tester
-
They are designed to detect quality defects in the insulation between winding turns, ensuring the reliability and performance of electrical components.
-
Product
Operational Historian Software
-
It is time to retire the warn-out clip boards and tedious transcription of critical plant performance data. FactoryTalk® Historian software captures operational process data from multiple sources at lightning speed. You gain a supreme level of supervisory control, performance monitoring and quality assurance with robust FactoryTalk Historian software that can scale from machine to enterprise. Reliably recording time-series records at this pace would be impossible, even for your most caffeinated plant-floor record keeper. FactoryTalk Historian dashboards take that work off your hands. Plus, the added confidence in forecasting trends with reliable data will generate new level of productivity. So long, clip boards. You won’t be missed.
-
Product
Low Capacity (in-lb) General Purpose Reaction Torque Sensor
TRT SERIES
-
The TRT Series reaction torque sensors offer long term reliability due to non moving parts and state of the art bonded foil strain gages. Whenever possible, the best approach for precision torque measurements is via reaction torque sensing, eliminating high maintenanceand high cost of slip rings, bearings and brushes.
-
Product
Demagnetizer
-
"Demagnetization" is indispensable in the manufacturing industry that produces products made of iron. NDK proposes a high-performance and highly reliable demagnetizer that best matches the customer's application .
-
Product
Real-time S-Parameter And Power Measurement Uncertainty
S96015B
-
See real-time measurement uncertainty for S-parameters and power measurements with the measurement traces on one screen. Estimate uncertainty reliably and apply more realistic limit lines for pass/fail tests for better production yield rates
-
Product
Frequency Counter (225MHz - 18GHz)
S43180
-
S43180 series high-precision frequency counter is a high-precision frequency measurement instrument. It has a frequency measurement resolution of 10 bits per second. The whole machine scheme adopts countdown technology and digital interpolation technology to realize the high-precision measurement of the instrument. It has measurement functions such as frequency, period, frequency ratio and powerful mathematical statistics operations (maximum value, minimum value, average value, PPM, standard deviation, Allan variance).S43180 series has reliable performance, complete functions, high measurement accuracy, wide frequency measurement range, high sensitivity, large dynamic range, high cost performance and easy to use. It is especially suitable for frequency measurement in scientific research and measurement fields such as aerospace, crystal oscillators, and components.
-
Product
Infrared Camera System
FlareSpection
-
The FlareSpection™ system provides extremely clear and reliable flare image and pilot flame monitoring of multiple flare tips. FlareSpection optimizes plant operations, improves safety, and ensures regulatory compliance. It enables you to remotely and automatically confirm flare operation and detect differences in flare stack heat signatures.
-
Product
Low Capacity (inch-ounce) Reaction Torque Sensor
RTS SERIES
-
The RTS Series torque sensors were designed to fill the need for accurate torque measurements below 62.5 in.lbs. without giving up stiffness or sensitivity to forces from other directions. They are manufactured from sensor quality aluminum and anodized for long term durability. Bonded foil strain gages and materials of the highest quality are installed assuring high reliability. The four bolt hole pattern with the use of our O.D. or I.D. pilots on either end allows simple adaptation to any application.
-
Product
Rotary Shock Machines
GHI Systems
-
* 0 Velocity before shock ? eliminates inertia effects. * Compact design allows use of imaging sensors. * Bidirectional operation. * Unsurpassed for latch testing, any format size. * Reliable MEP programmers in various durometers. * Interchangeable high amplitude table option. * Conforms to ?Dell? requirements.
-
Product
Small Unmanned Aircraft System
Aerosonde®
-
Designed for expeditionary land- and sea-based operations and equipped for simultaneous day/night full-motion video, communications relay, signals intelligence and a customer-selected payload in a single flight, Textron Systems' Aerosonde Small Unmanned Aircraft System (SUAS) delivers reliable, multi-mission performance in a class by itself. It is field-proven with more than 500,000 flight hours, including desert heat and Arctic cold.
-
Product
Touchscreen Panel 1.9GHz PC for Harsh Environments
PPC65B-1x series
-
Advanced IP65-rated Panel PC delivering high reliability and an extended operating temperature range in a thin, fanless design. The PPC65B series offers a rugged design for extreme environments and industrial IoT applications ranging from -20ºC to +70ºC. 1.9 GHz Quad-Core Intel® Atom™, E3845 processor, Up to 8 GB of RAM, Supports Linux, Windows 10 Operating Systems, Fast Graphics at High Resolutions • Five-wire resistive touchscreen • Resolution: 1024 x 768 / 1280 x 1024; 5 screen sizes 10.4" - 19".
-
Product
Anti-Sulfur Resistors
-
Panasonic Industrial Devices Sales Company of America
Panasonic offers a wide variety of Thick Film Current Sense Resistors (ERJ-B1, B2, xB, xBW, xCW) in a large range of case sizes and in wide terminal types for high solder joint reliability. The ERJ Series of Current Sense Resistors offers power ratings up to 2W with low ohmic ratings ranging from 5mΩ to 10Ω. Panasonic’s Thick Film Current Sense Resistor portfolio offers a more cost effective option with high reliability. Panasonic has a wide line of case size options ranging from 0402 to 2512 in conventional terminal and 0612 to 1020 for wide terminal.
-
Product
BGA SMT Adapters
Giga-snaP™
-
Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapter line of products provide an inexpensive and reliable method for attaching BGA chips to target board. The product line consists of patented female sockets with machined pins epoxy over-molded into an assembly that matches a particular BGA pattern. The epoxy over-molded female BGA socket is soldered to a PCB using standard soldering methods. A corresponding male pin BGA adapter, to which the user attaches their BGA chip, is plugged into the female socket on the board thus interconnecting the chip and the system is ready to go. The SMT adapters have the same solder ball types as the chips they are emulating. These adapters have less than half of the insertion force of competitive adapters, shorter electrical path for highest speed, and can be solder reflowed numerous times. A complete description and drawings of Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapters can be found at the tables shown below.
-
Product
Test Fixture Kits
Test Fixture
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
-
Product
Data Loggers
-
Delta-T Devices has produced high quality data loggers for over 25 years. We have a wealth of experience in the design of accurate, reliable, low-powered, weatherproof loggers. Our data loggers are versatile and cover applications across scientific research, environmental monitoring, horticulture and precision irrigation.
-
Product
Uniaxial Powder Tester
UPT
-
The Uniaxial Powder Tester (UPT) is a unique stand-alone uniaxial shear tester for simple, sensitive and cost effective powder characterisation. The instrument delivers repeatable and reliable measurements, providing a robust alternative to traditional powder testing techniques.Uniaxial testing first involves the construction of a consolidated powder column. This is then removed from its confining sleeve before being fractured through the application of a vertical stress, directly measuring the uniaxial Unconfined Yield Strength (uUYS). This technique can therefore be used to assess and rank powder flowability.
-
Product
Man Portable Long Range Ground Surveillance Radar
Ranger® R6SS
-
The man-portable Ranger® R6SS is an electronic scanning, long-range radar specifically designed to detect and track personnel and vehicles within a 10-km range. Light and small, the Ranger R6SS provides best-in-class target detection and acquisition performance in a form factor that fits in a backpack. Its low false alarm rate and extremely reliable operation builds operator trust and yields high operational availability.
-
Product
Instrument for linear accelerators and TomoTherapy® systems
QA BeamChecker™ Plus
-
The NEW QA BeamChecker Plus is a reliable and uncomplicated daily QA instrument for linear accelerators and TomoTherapy® systems.
-
Product
Synchro/ARINC 429/Fuel Flow Modules
-
NAI designs and manufactures a wide variety of self-contained, remotely mountable, Signal Converter Modules:*Synchro/Resolver Booster AmplifiersS*ynchro/Resolver Converters*ARINC 429-to-Synchro Converters*Second Harmonic Fuel Flow ConvertersTheir field-proven designs and carefully selected components assure highly reliable performance. These military grade modules are specifically designed for rugged defense and industrial applications.
-
Product
HeavyDuty encoders absolute
-
Reliable positioning without the need for referencing. Under the harshest conditions.
-
Product
RF Power Transistors
Silicon MOSFET
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer a broad range of silicon bipolar transistor products designed for applications ranging from DC to 3.5 GHz. Our silicon bipolar transistors are ideal for civil avionics, communications, networks, radar, and industrial, scientific, and medical applications. Our all-gold metallization fabrication processes ensure high performance and long term reliability for ground and space applications.
-
Product
Cable TV
-
Tempo Communications provides technicians with an array of test and measurement solutions to optimiz... e the installation and performance of broadband cable networks. The tried-and-true TDR from Tempo delivers all of the enhanced features required to pinpoint faults and verify performance. Like all of its test and measurement devices, the focus is on reliability, ease-of-use, and quality—empowering technicians to do their jobs and exceed customer expectations.Show less
-
Product
PXI Single 32x8 Matrix Card, 1 Pole
40-530-021
Matrix Switch Module
Typical applications for this high-density reed relay matrix include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules. For example, seven PXI modules will form a 224x8 Matrix, a total of 1792 crosspoints in a 7-slot PXI Chassis.
-
Product
Probing Solutions
ES62X-CMPS
-
The ES62X-CMPS compact manual probe station is a rugged wafer probing solution designed for high reliability, compact size and low investment cost. It enables manual wafer level measurements up to 300 mm wafers. The probing station can also be used for TLP, HMM, HBM, LV-Surge, RF, S-parameter and DC-measurements. Micro positioners with vacuum as well as magnetic base can be attached. The chuck has a vacuum interface for the wafer and is electrically isolated. Multiple 4 mm connectors can be used to connect a voltage potential to the wafer backside.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 2.5 GHz, 4 Analog Plus 16 Digital Channels
MSOS254A
Oscilloscope
2.5 GHz bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.4 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
Automated Multi-Functional Tester
QTouch 1408 C
Functional Test
Qmax Test Technologies Pvt. Ltd.
QTouch 1408 C – Automated Multi-Functional Tester with in-built camera is designed to make automatic image capturing and probing of electrical signals with ease and speed especially in PCBs with high density/high pin count device that are mounted on the PCB. It is designed to move on X, Y, Z directions making it possible to probe every component as close as 20 mils. Easy tagging feature allows the user to get the real time XY coordinates using the library information with minimal intervention. CAD import feature is available for Auto Test Generation/to extract the XY coordinates from the CAD data. Qmax Automated Multi Functional Tester can perform Board level functional test of a PCB and guided probe / Back tracking diagnostics utility to reliably test Digital, Analog and Mixed Signal PCBs and fault isolation to the PCB level or component level.
