Bus Translator
Bus Converters are used as an interface between separately powered components of a logic system.
See Also: Bus
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB110
-
The FAB110 offers one PCIe x16 slot, one PCIe x4 slots and two 32bit/33MHz PCI slots as well as the PICMG 1.3 slot for the SHB (system host board). The onboard 24-pi ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB110 is designed for the 6-slot industrial chassis, such as Axiomtek's AX60501 and AX6052.
-
Product
I2C Bus Monitor - USB
Model JI-216
-
The JI-216 I2C Bus Monitor is a low cost, easy-to-use PC hosted instrument specificallydesigned for troubleshooting and debugging I2C networks. The JI-216''s FPGA basedarchitecture provides for the capture and display of all valid or invalid messages and I2Cbus events. Captured I2C messages are available for display in two modes: real-timestreaming, or triggered. These modes provide optimized data display for either hardwareor software development. The SDA/SCL timing display aids in tracking down and solvinghardware timing problems. JI-216''s broad bandwidth (DC 3.4Mbits/s), wide input signalrange (0 15.0V), and variable signal filtering provides flexibility in monitoring a variety ofI2C bus systems. An intuitive Windows application manages instrument setup andcontrol. Communications and unit power is provided via a USB 2.0 link.
-
Product
PXI 8 Slot BRIC 506x8 1-Pole Dual Analog Bus (11 sub-cards)
40-560A-121-506X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Bus Analyzer
FireSpy® 3422bT/3822bT
-
The FireSpy3422bT and FireSpy3822bT bus analyzers are DapTechnology's latest 3-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy3422bT/3822bT is the most advanced 1394 test equipment in the market. The FireSpy3422bT/3822bT in fact combine three FireSpy analyzers in one single instrument. They comprises a significantly more powerful on-board processor and improved connectivity to the host.
-
Product
PCI Express® Bus To 3U PXI Express™ Chassis Expansion Kit
ACL-EXPRESS-7
-
The PCIe-to-PXIe expansion kit includes one PCIe-8560, one PXIe- 8565, and one ACL-EXPRESS cable (7 meters).
-
Product
PXI Single Bus 32-Ch 2A Fault Insertion Switch
40-190B-201
Fault Insertion Unit
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PCI Express® Bus to 3U PXI Express™ Chassis Expansion Kit
ACL-EXPRESS-1
PXI Express Module
The PCIe-to-PXIe expansion kit includes one PCIe-8560, one PXIe- 8565, and one ACL-EXPRESS cable (1 meter)
-
Product
Standardized Bus Interface
IP-429-II
-
Connect to your Avionics with IP-429. Pick 2,4,6,or 8 ARINC 429 compatible receivers and 1, 2, 3, or 4 transmitters. Transorb protected IO. Software programmable transmit rates [100K or 12.5K]. Time Tag on received data. IndustryPack campatible with 8 or 32 Mhz. bus operation.
-
Product
PXI 4-Slot BRIC Matrix, 230x8, 1-Pole (5 sub-cards) Dual Bus
40-560B-021-230X8-M
Matrix Switch Module
The 40-560B-021-230x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
Serial Bus Buffers, Extenders, and Accelerators
-
The Analog Devices family of I2C solutions support hot swappable, 2-wire bidirectional bus buffers to allow I/O card insertion into a live backplane without corruption of the data and clock busses. Additional supported 2-wire buses include SMBus, PMBus, the ATCA intelligent platform management bus (IPMB), and the HDMI DDC bus. I2C/SMBus Accelerators improve bus transitions to allows multiple device connections or a longer, more capacitive interconnect, without compromising slew rates or bus performance. ADI's software-programmable and pin-selectable I2C multiplexers help resolve I2C address limitations, increase fan-in or fan-out, and integrate bus buffers and rise time accelerators for an all-in-one solution. Resistor configurable I2C address translators can be configured with over 100 unique slave addresses to allow multiple slave devices with the same address to coexist on the same bus.
-
Product
PCI Smart Bus Extenders
Live Insertion PCI Bus Extenders
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment. The capabilities of Ultraview's two models of Universal 66/33MHz 64/32-bit PCI extenders are as follows:
-
Product
PXI 8 Slot BRIC 92x8 1-Pole Dual Analog Bus (2 sub-cards)
40-560A-121-92X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 184x8 1-Pole Dual Analog Bus (4 sub-cards)
40-560A-121-184X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 4-Slot BRIC Matrix, 92x8, 1-Pole (2 sub-cards) Dual Bus
40-560B-021-92X8-M
Matrix Switch Module
The 40-560B-021-92x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Dual Bus 32-Chan 2A Fault Insert Switch, N/O Through Relays
40-190B-502
Fault Insertion Unit
The Dual Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel.
-
Product
Bus Differential System
B30
-
The B30 features integrated protection, control and metering for MV, HV and EHV busbars, providing cost effective, feature-focused busbar protection. Use the B30 to protect busbars with up to 6 feeders with up to two three phase differential zones. The B30 is a cost effective alternative to high impedance schemes, ideal for breaker-and-half bus schemes, with integrated feeder backup protection and metering
-
Product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 8 Channel
50-200-008
Fault Insertion Unit
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
Product
PXI 8 Slot BRIC 322x8 1-Pole Dual Analog Bus (7 sub-cards)
40-560A-121-322X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
compactPCI Bus Pin Assignment
-
VECTOR Electronics and Technology, Inc.
cPCI Bus pin assignments per PICMG 2.0 R3.0
-
Product
PXI Dual Bus 32-Chan 2A Fault Insert Switch
40-190B-202
Fault Insertion Unit
The Dual Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A, Hardware Interlock
40-194A-001-HI
Fault Insertion Unit
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with hardware interlock and one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
PCI Express® Bus to 3U PXI Express™ Chassis Expansion Kit
PCIe-PXIe-8565
PXI Express Module
Includes PCIe-8560 peripheral card, PXIe-8565 3U system module, and ACL-EXPRESS cable in 1, 3, or 7 meter lengthsCompliant with PXI-5 PXI Express hardware specification Rev.1.0 and PCI Express Base Specifications Rev. 1.0a250 MB/s maximum system throughput
-
Product
Bi-Directional Level Translator
IFB-10001
-
Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.
-
Product
PXI Single Bus 74-Ch 2A Fault Insertion Switch
40-190B-001
Fault Insertion Unit
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
AMC For PCIe Bus Expansion
AMC113
-
AMC113 is VadaTech second generation PCIe expansion module. The AMC113 is a high-speed 20Gbps bridge from the host PCIe bus to VadaTech’s other carrier and Rear Transition Module (RTM) products such as the ATC104/114/118/117/119, ART114, μTCA chassis, etc. The different carriers host different I/O modules such as PMC/PrPMC, AMC, PCI-X and PCIe edge modules. This concept allows any of the available I/O modules in these standard form factors to be integrated quickly and easily into an AdvancedTCA or μTCA subsystem.The AMC113 allows expansion among multiple μTCA chassis or
-
Product
PCIe Smart Bus Extenders
-
The PCIeEXT16HOT enables PCIe x16/x8/x4/x2/x1 boards to be rapidly tested, removed and swapped without having to reboot or power down the host system enabling rapid production testing and engineering debug. The hot insertion, current reporting, overcurrent indication and limiting and voltage margining capabilities make this board the highest performance PCIe bus extender in the industry.
-
Product
LXI Reed Relay Matrix - Single 32x32 Plugin, No Direct Y Access, 1 Analog Bus
65-227-101
Reed Relay
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
Dual Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-102
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
14-slot PICMG 1.3 Bus Passive Backplane
FAB101
-
The FAB101 features one CPU card slot and thirteen 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Furthermore, the FAB101 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491, and AX6145, to house the FAB101 and any customer's industrial integrations flexibly.
