Interrupters
-
Product
PXI-8512, 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-02
-
2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
PXIe-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
780587-12
-
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-01
-
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
Split-Core Current Transformers
CTS Series
-
Continental Control Systems LLC
The CTS series CTs are available with windows from 0.75 inch up to 2.0 inch. They have a removable section, so that they can be installed without interrupting the circuit. 0.333 Vac output at rated current Accuracy ±1% from 10% to 100% of rated current Phase angle <2° degrees at 50% of rated current (valid for 70 A or higher) 8 ft. twisted-pair wire, 600 Vac rated UL recognized for voltages up to 600 Vac, CE mark, RoHS
-
Product
PCI Express, IEEE 488 GPIB Instrument Control Device for Windows
778930-01
-
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
Product
USB BUS Controller Board
MS 1711
-
- 8 bit and 16 bit compatible Read and Write Cycles- Single or Block Memory and IO Write Cycles- Interrupt Cycle Generation- The generated bus cycles signals is compatible with ISA96 system back plane- External Reset- Double Euro Standard Board- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Optical Fiber Identifier
TW3306
-
Techwin(China) Industry Co., Ltd
Optical Fiber Identifier TW3306Ais an essential installation and maintenance instrument. By inserting the fiber into its adapter head, it can identify SM optical fibers without any damage by detecting the optical signals being transmitted through them so as to avoid the opening of the fiber at the splice point for identification and thus avoids the interruption of the service.In the presence of traffic, the intermittently audible tone is activated.
-
Product
8-Ch, 16-Bit Counter/Timer Universal PCI Card
PCI-1780U
-
8 independent 16-bit counters8 programmable clock source8 digital TTL outputs and 8 digital TTL inputsUp to 20 MHz input frequencyMultiple counter clock source selectableCounter output programmableCounter gate functionFlexible interrupt source selectBoardID™ switch
-
Product
PXI Vehicle Multiprotocol Interface Module
-
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Refrigerant Leak Detection Camera
FLIR GF304
-
The FLIR GF304 detects refrigerant gas leaks without interrupting or shutting down operations. Refrigerant gases are highly toxic, environmentally harmful, and heavily regulated. By detecting refrigerant gas leaks early, companies can avoid the cost of replenishment and limit environmental impact. The GF304 allows inspectors to visualize these gases, discover hidden leaks, and confirm repairs once their complete.
-
Product
Power Quality Analyzer
Dranetz HDPQ® Plus Family
-
Record sags/dips, swells, interruptions, transients, harmonics, flicker, RVC, power, demand, energy and much more
-
Product
RTD Measurement for CompactPCI
CPCI390
-
The CPCI390 has a 3U form factor and features six 2-, 3-, or 4-wire high-accuracy RTD measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued. The local DSP (TMS320C203) performs linearization, auto-calibration and alarm limit checking. Sensordata is available in °C, °F, K and Ohm. All inputs are optically isolated from the system.
-
Product
4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V
CPCI-7500
-
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS
-
Product
STD Bus Backplane
-
VECTOR Electronics and Technology, Inc.
Vectorbord® STD Bus industrial backplanes per IEEE 961 microcomputer bus, compact and rugged are fully assembled and tested. Designed for 4.5” X 6.5” plug-in boards, Vector STD Bus backplanes are available in 8 or 16-slots. Speed capability up to 10MHz; 2-layer design. Ample positions for decoupling capacitors; interrupt priority lines.
-
Product
PCI, IEEE 488 GPIB Instrument Control Device for Windows
778032-01
-
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
Product
PCI-8516, 2-Port, PCI, LIN Interface Device
781365-01
-
2-Port, PCI, LIN Interface Device—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
Product
NI-9266 , 8-Channel C Series Current Output Module
785046-01
-
8-Channel C Series Current Output Module - The NI‑9266 is ideal for interfacing and controlling industrial current-driven actuators. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9266 includes channel‑to‑earth ground isolation for safety and noise immunity.
-
Product
VXI IP Carrier Module
DP-VXI-5124
-
The Data Patterns DP-VXI-5124 is a VXI 'C' size Carrier Board, which occupies a single slot in the VXI system. The module is a register based device with A16/A24/A32 address space and has interrupter capability. The carrier board's VXI bus interface is used to program and monitor the carrier board registers for configuration and control of the board. The VXI bus interface is also used to communicate with and control the external devices that are connected to an IP modules field I/O signals.
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-ST
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
PXI-8513, 1‑Port, Software-Selectable PXI CAN Interface Module
780688-01
-
1‑Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCI-1564
-
32 bit, 33 MHz, PCI interfaceInput channels32 isolated digital input channels, 24 V, incl. 16 interruptible and 3 fast counter inputsInput channels organised in 4 groups of 8 channels, each group has its own ground lineVoltage reversal protectionAll inputs are filteredOutput channels32 isolated digital output channels, 10 to 36 VOutput current per channel 500 mAWatchdog for resetting the outputs to "0"After power/ON the outputs are reset to ì0îShort-circuit current for 16 outputs ~ 3 AShort-circuit current for 32 outputs ~ 6 AShort-circuit current per output ~1.5 AElectronic fuseOvertemperature and overvoltage protection24 V power outputs with protection diodes and filtersSpecial output capacitors minimise electromagnetic emissionsExternal 24 V supply screened through a protection circuitryShutdown logic when the external supply voltage drops unter 5 V
-
Product
SparkFun 6 Degrees Of Freedom Breakout
LSM6DSO (Qwiic)
-
The SparkFun LSM6DSO 6 Degrees of Freedom Breakout is an accelerometer and gyroscope sensor with a giant 9kB FIFO buffer and embedded processing interrupt functions. Due to the capabilities and low cost of the LSM6DSO we've created this small breakout board just for you! Each LSM6DSO breakout has been designed to be super-flexible and can be configured specifically for many applications. With the LSM6DSO breakout you will be able to detect shocks, tilt, motion, taps, count steps, and even read the temperature!
-
Product
Vacuum Interrupter Tester
VIT
-
Veer Electronics make Vacuum Interrupter Tester that tests the Vacuum Interrupter Integrity by applying a Pulse DC Voltage across the Interrupter under Test. When this Voltage is applied to the Vacuum Interrupter, if Interrupter is defective then an electronic Buzzer gives Audio indication as well as Red color LED will gives Fail Indication. If Interrupter is in Healthy Condition, then the Instrument will gives Pass Indication with Green LED light.
-
Product
Switch
TOE 9261
-
Toellner Electronic Instrumente GmbH
Input voltage 60 V, Output current up to 100 A, Rise / fall time < 500 ns, Short-circuit-proof, Switchable discharge of load circuit, Interruption in supply and ground lines up to 100 A, Switchable buffering of input circuit, 4 signal line switches, Control with any signal generators (TTL level)
-
Product
64 Channel Isolated Digital Input / Interrupt Output Module
DP-cPCI-3069
-
DP-cPCI-3069 provides 32 Channel Digital Input / Interrupt and 32 Channel Digital Output with isolation. 32 Channel Inputs and 32 Channel Outputs are divided into groups of 16 channels each and are routed to rear I/O only.
-
Product
PC/104 Input/Output Module providing 96 lines of digital I/O
PCM-UIO96C-16
-
The PCM-UIO96C-16 is a highly versatile PC/104 input/output module providing 96 lines of digital I/O. One important feature of this card is its ability to monitor 48 of the 96 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O.
-
Product
PANAVIA Modules
-
AIM’s PANAVIA test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core design with one processor for real time bus protocol support, massive memory and IRIG-B time code encoder/decoder functions are standard. AIM delivers versions of our modules with extended temperature range and conformal coating. With 8 Tx and 8 Rx channels per module, functions include autonomous transmit sequencing, continuous clock and data transmissions, host controlled double buffering, programmable interrupts, data selection on specific tag identifier, selectable triggers on data and/or tags with full protocol error injection/detection, real time bus recording and time stamping to ensure your bus integrity. Each module is delivered with a Board Support Package (BSP) comaptible to the legacy PCI and cPCI hardware modules.
-
Product
Process Timers
TCT101-1ABC
-
The Process Timer TCT101-1ABC is a panel mount 4 digit 2 line display meter that can be set up for various Timer functions, such as Timer Off, Timer On, Pause Timer, Timer On and Off, Propotinal Timer. The TCT101-1ABC has 2 relays that can be used for various functions and has 5 Amp contacts. The timer periods can be set in multiples of 1 hundredths, 1 tenths of a second, seconds, minutes or hours. With the aid of the front touch panel or digital input it is possible to interrupt the timer. The unit also has a function that can set the output to toggle on and off over a period of time.
-
Product
USB-8501, 2-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786307-01
-
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Current Transformer Field Test Set
1043
-
The Catalog 1043 Current Transformer Field Test Set is a simple and inexpensive means whereby a current transformer installation may be quickly checked for many sources of trouble. The tests are made without interrupting the Customer's service and while the load is on.
