DC DC Converters
-
Product
16 or 32 channel Digital to Analog Converter
LS-71-P
-
The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.
-
Product
Thermal Voltage Converter
1395B
-
The 1395B TVC. Has better thermal stability than it's predecessor. Measuring ac voltages between 20 Hz and 100 MHz with increased accuracy and reliability. The 1395B can be used as a primary ac voltage standard and/or standard for the calibration of ac calibrators and voltmeters.
-
Product
DC Electronic Load
63600 series
-
Chroma's 63600 series DC electronic loads are designed for testing multi-output AC/DC power supplies, DC/DC converters, chargers, batteries, server power supplies, and power electronic components. They are excellent for research, development, produc t ion, and incoming inspection applications. The 63600's state of the art design uses DSP technology to simulate non-linear loads using a unique CZ operation mode allowing realistic loading behavior. The 63600 series can draw its rated current under very low voltage (0.4V typical). This unique feature guarantees the best loading performance for modern Point-of-Load conditions and fuel cells.
-
Product
D/A Converter
DA-4130
-
The DA-4130 D/A converter converts BCD output signal from Ono Sokki's digital gauge DG-4000 series, RV series reversible counter or other devices into analog signal to be recorded with pen recorder, etc.
-
Product
DC Resistance Tester
ZLD-10
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.2-2008Used to measure conductor with nominal diameter ≥0.01～9.0mm or various round or flat copper and aluminum wires and other metal wires with DC current resistance of 100μΩ～99.99Ω;Combination of intelligent DC conductor resistance measuring meter and DC resistance test fixture with sample straightening function;Test range can be selected according to the resistance value of sample, and after clamping samples current resistance value would be displayed;Both potential fixture and current fixture are made of copper;The application of microcomputer control allows for full-automatic completion of test;LED will intuitively display measurement results;
-
Product
Advantage Xi Radar Scan Converter
-
Curtiss-Wright Defense Solutions
The Advantage Xi radar scan converter is a half-size PCI card. Radar video arrives into the card through the PCI bus, which allows the card to be used in a client-server configuration with radar distributed over a network, or in conjunction with a radar interface card such as the Virgo PCI and Osiris PCI.
-
Product
Programmable Step Attenuator, DC to 40 GHz, 0 to 11 dB, 1 dB steps
84904L
Attenuator
The Keysight 84904L programmable step attenuator offers coaxial measurements to 40 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life (greater than 5 million switching cycles per section) and an attenuation range of 0 to 11 dB in 1-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with with only 2.4 dB of loss at 40 GHz. The compact size of the unit, 35% smaller than the Keysight 8495/7 (26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
Product
DC Electronic Loads
-
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.Both static and fully dynamic DC loads are offered. With dynamic functionality 2 levels of load current can be set. The rise and fall time can then be adjusted together with the time period spent at each level. The load can also be made to follow complex waveforms by tracking an external arbitrary oscillator input.
-
Product
Brushless DC Motor Drivers
-
ST’s STSPIN drivers for 3-phase brushless DC (BLDC) motors includes power drivers in a 3-phase bridge configuration and integrated solutions with built-in decoding logic for Hall-effect sensors.
-
Product
Precision Mechanical Calibration Kit, DC To 26.5 GHz, 3.5 Mm
85052C
Mechanical Calibration Kit
The Keysight 85052C precision mechanical calibration kit contains precision standard devices to characterize the systematic errors of Keysight network analyzers in the 3.5 mm interface. This kit also contains adapters to change the gender of the test port and a torque wrench for proper connection.
-
Product
Standard High Speed D/A Converters
-
Analog Devices digital-to-analog converter (DAC) portfolio provides solutions for your high speed and precision DAC applications. Thanks to complete data sheets and evaluation boards, as well as broad support among our clock and timing, RF, power management, and op amp portfolios, our DACs can help you reduce time to market and system design costs. A high speed range from 30 MSPS to multi-GSPS, 8- to 16-bit resolution, and a tiny package are just some of the features that make our industry-leading d/a converters stand out.
-
Product
DC Power Supplies
-
AMETEK Programmable Power, Inc.
From benchtop supplies, modular power supplies to rack-mounted industrial power subsystems, AMETEK Programmable Power, is a leader in designing and manufacturing precision, programmable DC power supplies. Ranging from 30W to 150kW, Sorensen DC power supply products are used in R&D, test and measurement, process control, power bus simulation and power conditioning applications across a wide variety of industrial segments.
-
Product
Adapter, 1.0 mm (m) to 1.0 mm (m), DC to 110 GHz
11920A
-
The Keysight 11920A precision 1.0 millimeter waveguide-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 110 GHz.
-
Product
5-Port Coaxial Switch, DC to 4 GHz
8764A
-
The Keysight 8764A offers excellent electrical and mechanical performance with broadband operation, high isolation, low SWR, long life, and exceptional repeatability.
-
Product
High Voltage DC Power Supply
IT6700H Series
-
IT6700H series high-voltage DC power supplies is with maximum output power 3000W, adjustable voltage 0-1200V and current 0-10A, IT6700H series have desktop and shelves installation function, easy to operate. IT6700H series provide list mode, built-in RS232 / USB / GPIB communication interface, rich SCPI instructions facilitate the formation of a variety of intelligent test platforms.
-
Product
DC Control Tools
-
Assembly designs are getting more and more complex while production speeds continue to increase. To compete, lean manufacturers strive to complete more work with fewer tools. A single Mountz DC control tool can do the work of 2-15 regular tools, saving space and increasing production. Mountz DC control tools are easy to program and can remember up to 30 process sequences with 20 program steps. This gives you the flexibility you need to carry out varied and complicated manufacturing plans. A Swiss DC servo motor controls torque delivery with clockwork repeatability. Combined with built-in screw counters and error-proofing software, Mountz DC control tools offer supreme production results and product oversight. And by providing documented fastening results, Mountz DC control tools also make regulatory compliance easy.
-
Product
Signal Converters
-
On one hand, there are signal converters which transform an input frequency range into an analog signal. These signal converters are very easy to program and control. Other signal converters can transform analog input signals into analog normalized signals with galvanic insulation. Due to the fact that these signal converters can be freely graduated, they offer endless possibilities and 110 combinations can be selected by means of a DIP switch. Other kinds of signal converters can be connected to devices with RS-232, RS-485 or RS-422 protocols.
-
Product
Single-Channel Voltage Output D/A Converters
-
Analog Devices offers a broad portfolio of single-channel voltage D/A converters, which includes many leading products in performance and package size, with resolutions from 8-bit to 20-bit, low power, and a serial SPI, parallel, or I2C interface. Within the industry’s smallest packages, we offer more functionality within smaller board and module sizes. The integration of a precision reference minimizes board area and costs, eliminates the need of calibration, and reduces the number of external components to simplify the design stage.
-
Product
Down Converter
-
The products have a big Dynamic Range, are highly linear and have low Noise Figures to keep the best possible quality of the signals to be converted. For this reason an internal filter for secondary wave suppression is implemented.
-
Product
DC Power Supply
-
Our broad selection of both bench-friendly and system-ready instruments can meet your testing challenges - from basic to complex - with a wealth of available capabilities.Test confidently with clean, precise DC power that's fully specified and guaranteedSafeguard loads from potential harm with robust output protection and fault detection capabilitiesEnhance system flexibility with built-in, DMM-quality measurement functions
-
Product
400-Watt DC/DC Converter
VPX55-3
DC Converter
NAI's VPX55-3 is 400-Watt DC/DC Converter that plugs directly into a standard 3U VPX chassis with a VITA 62 0.8" power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7-16
85038A
Mechanical Calibration Kit
The Keysight 85038A calibration kit contains open circuits, short circuits and terminations with both male and female 7-16 connectors and has frequency coverage from dc to 7.5 GHz (usable to 8 GHz).
-
Product
Scienlab Regenerative DC Emulator
SL1800A Series
-
Keysight's SL1800A Scienlab Regenerative DC Emulator - High-Power Series enables users to emulate the large batteries in electric vehicles. The bidirectional power flow allows emulation of both power sourcing applications, such as traction inverter test, as well as power-absorbing (sinking) applications, such as EV charging. Being regenerative, the power absorbed is delivered back to the grid, saving on energy and cooling costs. The SL1800A Series is fully integrated with the SL1040A Scienlab Charging Discovery System. The SL1093A Scienlab Charging Discover Software fully automates DC charging applications to many different test standards. With bi-directionality, integrated DC voltage and current controllers, high dynamics, and its regenerative energy feedback capacity, the Scienlab Dynamic DC Emulator provides an all-in-one system for efficient and effective testing of the power electronic components in electric vehicles (EV) and electric vehicle supply equipment (EVSE).
-
Product
Converter Signal Amplifier – 4…20 mA – DIN Rail
HD978TR3
-
Configurable converter signal amplifier with 4…20 mA (20…4mA). Input range -10 …+60mVdc.
-
Product
O/E Converter
TIA-4000
-
The TIA-4000 is comprised of a fibre coupled InGaAs APD detector combined with a variable reverse bias voltage network and fast transimpedance amplifier. The output of the unit is brought out to a type K female SMA connector. Light falling on the detector generates a positive-going proportional current. This current, multiplied by the transimpedance produces a voltage that is proportional to the light incident on the detector surface.
-
Product
Medium-power DC Electronic Load (900W~6000W)
FT6400A Series
-
Shenzhen FaithTech Technology Co., Ltd.
The FT6400A series has modular design, with strong adaptability, high reliability and high maintainability. Mainly used in power electronics testing fields such as power batteries, medium and high power DC power supplies, DC generators, etc. The FT6400A electronic load not only provides OCP, OVP, OPP, OTP, RVP but also provides Von and Voff functions and programmable protection functions for the device under test. These features can greatly improve the reliability of the product, and it is a reliable product for engineering test and automatic test system integration.
-
Product
Voltage Output D/A Converters
-
Analog Devices offers a large family of resistor string and R-2R voltage output (VOUT) D/A converters (DACs). From 8 bits up to 20 bits of resolution, single to 40 channels, integrated or external reference, parallel, LVDS, serial SPI or I2C interface, with high temperature operation, we have a D/A converter to suit your application. We provide precision, buffered, and unbuffered rail-to-rail VOUT D/A converters with up to ±1 LSB INL and DNL specifications and excellent offset and gain error. Our D/A converters work well in a wide variety of open-loop or closed-loop systems—adjusting gain, offset, and many other signals.
-
Product
Signal Converters For High-accuracy Angular Measurement
EIB 1500 series
-
*Interpolation and digitizing electronics for the real-time digital processing of positions from two scanning heads*Input: incremental rotatory HEIDENHAIN encoder with two scanning heads and distance-coded reference marks (relative orientation of scanning heads: 180° ± 5°)*Output: EnDat 2.2, Fanuc Serial Interface, Mitsubishi high speed serial interface*Integrated subdivision: 16 384-fold
-
Product
4-in-1 OSLT Mechanical Calibration Kit, DC To 40 GHz, 2.92 Mm (f)
85561A
Mechanical Calibration Kit
Combines an open, short, load, and through standard in a compact unit that is easy to handle and lightweight.
-
Product
F/V Converter
FV-1100
-
The FV-1100 receives signal from a rotation detector or a similar device and outputs DC current or voltage signal proportional to its frequency. As the fluctuation of the input frequency signal is continuously converted to DC voltage, it is useful for measurement and recording of transient phenomena such as fluctuation of rotating speed, current velocity, frequency.
