-
Product
VCS
Test Specimen Parameters
-
a program from the scope of ZETLAB VIBRO software suite. The update of the software suite ZETLAB VIBRO includes a new user-friendly interface as well as a wide range of new functions, allowing the user to configure parameters of the vibration test system with the maximal possible prevention of errors occurrence.
-
Product
PXI-8433, 2-Port, Isolated, RS485/RS422 PXI Serial Interface Module
779744-01
-
2-Port, Isolated, RS485/RS422 PXI Serial Interface Module - The PXI‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Rope Tension Meter
RTM
-
The PIAB RTM Rope Tension Meter is very simple and handy to use. Simply hold and “clip” it to the rope to be tested and use the large hand screw to deflect the rope to a fixed angle. The resultant force will affect the load cell and measure the tension in the wire rope. The resultant signal is digitally processed and displayed in a selected pre programmed graduation. The PIAB RTM 20D can be graduated in kN, klbs or in ton.
-
Product
Analysis Tool
CANalarm
-
The CANalarm is a low priced analysis tool that can be installed in the bus permanently. It makes it possible to build up a separate and redundant monitor without change of configuration and program of the master controller. It works passive and is therefore non reactive
-
Product
Elevator Drives
-
User friendliness is the emphasis of our drives. The keypad interface and programming are dedicated to elevator and escalator applications. The performance features are well-suited for both Induction and Permanent Magnet motors with the latest control functions.
-
Product
Temperature and Humidity Chamber
GT-C52
-
Temperature and Humidity Chamber is for conditioning of samples prior to testing. It also can be used for a variety of material of high - low temperature alternating test. The test temperature, humidity, time can be programmed. Provides conditions of temperature from -40 degree to +150 degrees and of humidity 20% to 98%.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-44
-
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Multi Channel Vibration Motor Aging Tester
BK2022
-
The BK2022 is the ultimate in aging testing for coin type vibration motors. You can connect up to 128 motors and the system will automatically test them all at the same time. It tests RPM, current, individual errors, and even total error and puts the information on the monitor in real time. You can store the results and retrieve them later to be analyzed so you can keep track of the accuracy and stability of your manufacturing process. In addition, BaKo’s BS1123-BS2022 program will be modified to fit your needs so that the testing you do is a custom fit.
-
Product
Load Cells
-
Honeywell Industrial Automation
Honeywell Sensotec manufactures a wide range of tension, compression, and universal measurement load cells. These load cells are manufactured as standard, modified standard, and custom sensors to provide fast delivery. Many units can ship from our extensive stocking program within 24 hours.
-
Product
Universal Tester Software Platform
-
APG (Automatic Program Generator) is a user-friendly 32-bit programming system aimed at providing fast and easy test program creation. It is a powerful Windows Application with all of the features of the Windows® environment enhanced by Autotest’s own Multi-Tasking Windows control.
-
Product
CIE Colorimeter Probe
K-1
-
The Klein K-1 tri-stimulus CIE Colorimeter Probe is designed to be the best colorimeter in sensitivity, stability and speed. It attaches directly to a pc's serial com port (RS-232), and runs with the companion pc program. Whether a desktop or a laptop is used, the Klein measurement application is in control and many additional features are available.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-104
-
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PXIe Arbitrary Signal Generator and Transceiver
-
The Tabor Proteus Series P948xM, P9082M, P258xM and P128xM models are arbitrary signal transceivers based on the PXIe platform. The modules combine transmit, receive and digital signal processing capabilities in a single device. The modular, compact and cost-effective systems offer unique performance, various configuration options, innovative task-oriented programming and a user-programmable FPGA.
-
Product
Photometric Converter
C4000
-
The C4000 converter is a multi channel controller capable of operating all optek photometric sensors. The C4000 converter allows for easy programming and operation, and can supply up to four real time configurable 4-20 mA output values correlated to any units of measure. The C4000 offers configurable relay alarms, can record and download process data, and can operate up to four sensors simultaneously.
-
Product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, RS-422 Inputs
APCIE-1711-5V-I
-
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many differentuser applications to be quickly and easily developed and reconfigured as further requirements arise. Thanks to the FPGA board structure, further counting applications canbe realised through software adaptation.
-
Product
PXI-8431, 4-Port, RS485/RS422 PXI Serial Interface Module
778985-01
-
4-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/4 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
AdvintRIO™ Reconfigurable I/O
PIRANHA
-
The Piranha platform employs a NI single board RIO (sbRIO), NI C Series I/O modules, and custom circuitry. Piranha systems are not dependent on a separate host computer. They offer both Ethernet, and Wi-Fi connectivity to a powerful real-time controller and high performance field-programmable gate array (FPGA) and up to two (2) C Series I/O modules. It provides stand-alone embedded execution for deterministic LabVIEW Real-Time applications. These controllers are designed for ruggedness, reliability, and low power consumption. The heart of Piranha system is the reconfigurable I/O (RIO) FPGA core. The RIO core has an individual connection to each I/O module and is programmed using easy to use elemental I/O functions to read or write signal information from each module. Multiple units can also be daisy changed together for larger applications.
-
Product
Programming on-chip flash in your processor
XJDirect
-
XJDirect is an advanced and innovative method for programming the internal flash of your processor and implementing some aspects of board test through JTAG when traditional boundary scan techniques cannot be used.
-
Product
Coherent DDS Modules
-
ITS has developed several custom Direct Digital Synthesizer modules that offer phase-coherent or phase-continuous operation at any frequency step size. These agile DDS modules can be programmed through direct parallel, Ethernet, or RS-232 interfaces.
-
Product
FD-11601, 8-Channel, ±10 V Powered-Sensor Voltage Input Device for FieldDAQ
786374-01
-
The FD-11601 measures up to eight channels with a voltage input range of ±10 V. Each input channel supports TEDS and provides 24 V DC to power external-powered sensors without additional power supplies. The FD-11601 features 24-bit resolution, simultaneous sample rates up to 100 kS/s/ch, and channel-to-channel isolation. It is IP65/IP67 rated to be dust-tight and water-submersible, operates in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11601 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11601 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. The FD-11601 is ideal for test cell and outdoor environments.
-
Product
NI-9403, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780179-01
-
5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals.
-
Product
Cormon Integrated Monitoring Software
CIMS
-
Cormon Integrated Monitoring Software (CIMS) processes real-time corrosion, erosion, pressure, or temperature data from up to 50 monitoring sensors to provide a complete picture of pipeline and device health. Alarm functions can be configured to ensure that potential issues are identified with ample time for correction, reducing operational risk and unplanned downtime. CIMS is the only industry software that can bring together data from both topside and subsea sensors, giving operators a comprehensive view into the entire asset integrity program.
-
Product
JTAG USB Controller
NetUSB-1149.1/E
-
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
Product
pH/DO/Conductometer
867/856 Modules
-
With the 856 Conductivity Module and 867 pH Module, you can build your own, customized solution – whether you are analyzing large sample loads or multiple parameters, or you want to enjoy full freedom when it comes to method programming and applications.
-
Product
9GS/s 8Bit, 4GS Mem 2CH 8 Markers AWG
P9082D
-
The Proteus P9082D, is a 9GS/s, dual channel arbitrary waveform generator packaged in a 4U, half 19” dedicated chassis, offering technologically advanced options and configurations that integrate the ability to transmit, receive and perform digital signal processing all in a single instrument. The P9082D offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
Product
IP Surveillance Camera
ENVIROMUX-IPCAM
-
View and control the camera from the ENVIROMUX web interface, the camera web interface, included software, or with a compatible cell phone. With the ENVIROMUX-2D/5D/16D, a triggered snapshot can be forwarded in alert e-mails. A snapshot can be triggered by any programmed event (motion detection, door open/close, glass break, smoke, liquid detection, etc.). Image sensor: 1/4" progressive scan CMOS sensor. Video Streaming: simultaneous Motion JPEG and MPEG-4. Frame rate: 30fps at 640x480 (VGA) resolution. Lens: F2.0, 4.0 mm (0.16 in). RJ45 connector. Wireless models: wireless IEEE 802.11 b/g up to 54 Mbps. Regulatory approvals: CE, FCC, RoHS.
-
Product
TMS Test Management Software
LX TMS
-
To diagnose and analyze electronic components and devices, various tests are required in development, production and service. Equipped with all the necessary standard functions, the test sequencer developed by LXinstuments meets all criteria for a successful and smooth test process. The test item ( DUT ) is examined under various operating conditions for its properties, function and usability. Typical areas of application can be found where the usual complexity of test sequences has to be processed. The test sequencer is therefore suitable for small and medium-sized systems where special functions of other sequencers are not required. The free, cross-platform, open source developer platform .NET serves as a starting point. The integrated WPF (Windows Presentation Foundation) framework ensures a user-friendly program interface.
-
Product
Universal Development Board For The PCAN-MicroMod CPU
PCAN MicroMod Evaluation Kit
-
As a plug-in module, the PCAN-MicroMod represents a simple way of providing electronic circuits with I/O functionality and CAN connection. The configuration is carried out with a Windows program that transfers the configuration data to the module via CAN. Several modules can be configured independently of one another on a CAN bus.
-
Product
Test Automation Platform Developer's System
KS8400A
-
The Keysight KS8400A Test Automation Platform (TAP) Developer's System provides powerful, flexible and extensible test sequence and test plan creation with additional capabilities that optimize your test software development and overall performance. Keysight TAP is a modern Microsoft .NET-based application that can be used stand-alone or in combination with higher-level test executive software environments. Leveraging C# and the power of Microsoft Visual Studio, TAP is not just another programming language. It's a platform upon which you can build your test solutions, maximizing your team's productivity by using your existing software development tools and infrastructure.
-
Product
EtherCAT Master Multi-Axis Motion Controllers
DMC-52xx0
-
The DMC-52xx0 EtherCAT Master is Galil Motion Control's first 32 axis motion controller. It is a pure EtherCAT controller capable of controlling up to 32 drives and 2 IO modules on one EtherCAT Network in a small, space efficient package. The DMC-52xx0 makes configuration and programming easy with just a handful of EtherCAT configuration commands and Galil’s intuitive, two-letter programming language. The DMC-52xx0 is offered in 2, 4, 8, 16, and 32 axis formats. Coordinated moves can be done within banks of 8 allowing for minimal changes to Galil’s programming language. Galil supports a variety of EtherCAT drives to accommodate most applications. The DMC-52xx0 operates in Cyclic Synchronous Position mode (CSP). In this mode the servo control loop is closed on the EtherCAT drive while the Galil sends motion profile data at a 1 kHz rate. The DMC-52xx0 features 8 uncommitted opto-isolated inputs and 8 uncommitted opto-isolated high power outputs. It also includes 8 uncommitted analog inputs and 8 uncommitted analog outputs. One 100 Mbps Ethernet port and one USB (serial) port are provided for communication with a host PC or external devices.
