High Voltage
electric power transmission is > 35,000 volts and for safety AC > 1000 and DC > 1,500. Also known as: HV
See Also: High Voltage Switching, High Voltage Meters, High Voltage Detectors, High Voltage Programmable Power Supplies, HV
-
Product
AC/DC High Voltage Dividers
VD-50 - 300
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Digital measurement of AC and DC voltages in one unit. Safe carrying aluminum case for storing and transporting.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-051-HI
Programmable Resistor Module
The 40-230-051-HI (PXI) and 42-230-051-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 2.95MΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Cut Ends, 2m HV, Exit Away From Pin 1
A050DM4-C-HA200
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-140-HI
Programmable Resistor Module
The 40-230-140-HI (PXI) and 42-230-140-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 102kΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High Voltage
-
A comprehensive range of high voltage power sources are available from ETPS. Product families range from programmable high precision laboratory power supplies to HV Cassettes and PCB modules. The flexible high voltage design platforms and responsive management structure enable us to offer an economically viable custom build. High voltage power supplies from ETPS are used in a variety of applications ranging from electron acceleration systems and mass spectrometers to magnetrons, x-ray and nuclear research.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-236-HI
Programmable Resistor Module
The 40-230-236-HI (PXI) and 42-230-236-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 395kΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe High Voltage Multiplexer, Single 48-Channel, 2-Pole
40-321-129-HI
Multiplexer Module
The 40-321-129-HI (PXI) and 42-321-129-HI (PXIe) are single 48-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-022-HI
Programmable Resistor Module
The 40-230-022-HI (PXI) and 42-230-022-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 1.81kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High Voltage Breakdown Tester
Model HV-100B
-
Laxtronics Instruments & Controls Pvt. Ltd
DC Output: 0 to 10 Kilo Volts continuously variable, AC Output: 0 to 5 Kilo Volts continuously Variable, Current Limit: 0 t
-
Product
Micro-Size Power Supplies
-
Advanced Energy’s micro-size, high voltage DC-to-DC converters offer a variety features — arc limits, tight line and load regulation, voltage monitoring, and more. Get the right solution in the perfect size.
-
Product
51-Pin REDEL High Voltage Cable Assembly, Male To Unterminated, Ferrules, 0.25A, 1m
A051KMR-F-HA100
Cable Assembly
This is a 1m long male to unterminated 51-Pin REDEL high voltage cable assembly with ferrules constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips areprovided to secure the connector to associated product.
-
Product
Digital Input Board
VME-1129
Digital Input Board
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
Product
Surge Voltage Generator
SSG 2100
-
Cable fault location with the BAUR SSG 2100. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-144-HI
Programmable Resistor Module
The 40-230-144-HI (PXI) and 42-230-144-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 1.5MΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Impulse Winding Tester
TH2883-1
-
Changzhou Tonghui Electronic Co., Ltd.
TH2883 series products are newly developed impulse winding testers by Tonghui. This product line makes Tonghui as the first provider of impulse winding tester from low voltage of 30V to high voltage of 10kV, single channel to multichannel (Max.:8 channels) in this industry. The instrument adopts popular 32 bit CPU and high density SMD technology, 65k color 7-inch TFT wide display screen, bringing ease for your eyes and convenience to your operation. The minimum impulse voltage of 30V, maximum impulse voltage output of 10kV, winding test of 1uH inductance value, sampling rate of 200Msps, memory depth of 6k bytes makes your test accurately. The usage of standard sample average, application of demagnetized impulse, high bandwidth analog acquisition circuit, technology of high-fidelity corona extraction as well as the opening of non-destructive test reflect the design philosophy “customer-oriented, share the future technology with you” of Tonghui.
-
Product
9-Pin D-Type Male, Solder Bucket, HV
92-960-009-M-HV
-
9-Pin Male D-Type Connector, High Voltage, Solder Bucket - Without Backshell
-
Product
Single Channel High Voltage Linear Amplifier
A600
-
The A600 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of 300V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 3 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
9 Pin D-Type, Male, Straight PCB Mount, HV
40-963-009-SM-HV
-
9-Pin Male D-Type Connector, High Voltage - Straight PCB Mount
-
Product
37 Pin D-type Connectors & Cables
-
These standard voltage and high voltage 37 Pin D-type connectors are used for both PXI & LXI switching and simulation products for medium density applications.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-324-HI
Programmable Resistor Module
The 40-230-324-HI (PXI) and 42-230-324-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 6.97kΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Surge Generators
Hybrid
-
Surge pulses occur due to direct or indirect lightning strikes in a circuit or by switching transients caused by switching inductive loads or short circuits. This leads to currents or electromagnetic fields causing high voltage or current transients. Surge voltages and currents can reach several thousands of volts and thousands of amperes. Our following Surge generators simulate these disturbances for all the necessary level in accordance with IEC / EN 61000-4-5 and IEC / EN 60060.
-
Product
PXI Attenuator Modules
-
Programmable RF Attenuators – accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices.Solid State Programmable RF Attenuators – available in triple or hex formats with bandwidths between 10MHz and 6GHz.High Voltage Attenuators – provide a convenient way of attenuating high voltage low frequency signals to levels that can be captured by other PXI devices without risk of damaging them.
-
Product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m, HV
A009DM5-C-HA050
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
Difference Amplifiers
-
A difference amplifier is a special purpose amplifier designed to measure differential signals, otherwise known as a subtractor. A key feature of a difference amplifier is its ability to remove unwanted common mode signals, known as common mode rejection (CMR). Unlike most types of amplifiers, difference amplifiers are typically able to measure voltages beyond the supply rails, and are used in applications where large dc or ac common-mode voltages are present. They are ideal for current and voltage monitoring. Analog Devices offers a range of difference amplifiers, optimized for low distortion, low power, or high voltage performance.
-
Product
Double IC Optic Node
OX 732
-
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics. Green Technology incorporated - Aluminium Housing for maximum heat dissipation.- Frequency 40 ~ 1000 MHz- Optical Wavelength : 1290 ~ 1600 nm- Flatness ±0.75 dB- LED Bar Display for Optic Signal Level- High C/N, CSO & CTB Characteristics- Inward Extruded Aluminium Channels for Maximum Heat Dissipation- High Voltage Surge Protection- -11 dBm Sensitivity- RF O/P at 0 dBm : 110 dBµV
-
Product
PXI-6233, 16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module
779620-01
Multifunction I/O
16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6233 is a bank-isolated DAQ device designed for voltage I/O. It offers analog I/O, digital input, sinking digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6233 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6233 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
Product
Semiconductor Curve Tracer
CS-3000 Series
-
*Max. Peak Voltage : 3,000V（HV mode）*Max. Peak Current : 1,000A（HC mode）*Equipped all models with LEAKAGE mode (Cursor resolution 1pA）*USB port for display hardcopy, waveform data (CSV format) and measurement setup SAVE/RECALL*LAN interface for Remote Control
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-254-HI
Programmable Resistor Module
The 40-230-254-HI (PXI) and 42-230-254-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 22.05MΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 1m, HV
40-972-037-1m-MU-HV
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
