Filter Results By:
Products
Applications
Manufacturers
Photovoltaic Cell
Convert light to electricity.
See Also: Photovoltaic, PV, Photovoltaic Reference Cells, Solar Simulation
-
product
Photovoltaic
For solar panel installations, problems such as insulation resistance degradation or issues with ground/earth continuity can pose a risk to safety as well as efficient operation. Continuous and predictive maintenance is essential to ensure regulatory compliance as well as the prevention of electrical hazards and fire risks, and enables operators to ensure the optimal performance of PV installations.
-
product
Uncooled InAsSb Photovoltaic Detector
P13894-011MA
Hamamatsu Photonics K.K. has developed an uncooled InAsSb (indium arsenide antimonide) photovoltaic detector that offers high-speed and high-sensitivity detection of infrared light in the 3 to 11 micron wavelength range. This new device (part number: P13894-011MA) extends the upper limit of sensitivity of Hamamatsu’s InAsSb detectors from 8 microns to 11 microns, which will enable users to measure molecules that absorb longer wavelengths of light and thus analyze more compounds with a single device.
-
product
Photovoltaic and Electrical Installation Testers
3108
MI 3108 EurotestPV is a combined photovoltaic tester and electrical installations safety tester. It enables complete testing of electrical installations according to EN 61557 standards and in addition performs all necessary tests required on single-phase photovoltaic (PV) installations. This includes all of the tests as required by EN 62446, but also includes I - U characteristic, Calculation of STC values as required by EN 61829 and power measurements on Inverter’s DC and AC sides.
-
product
Reference Cells
Reference cell is used for measuring and setting the intensity of solar simulators for one sun (or other user desired) intensity condition. They are also used to calibrate the IV Measurement system photo-detector intensity to match the measured ISC to calibrated ISC.
-
product
Load Cells
An array of load cells, including bending beam, tension and compression link, button, low profile, through hole, S type, cannister, tension link, and single point load cells as well as load pins.
-
product
Load Cell
Precise and robust and it has been designed to meet the requirements of a wide range of industrial weighing applications: hoppers, tanks, platforms. Is able to work in severe environmental conditions typical of applications in food, chemical and pharmaceutical industries.
-
product
Voltammetry Cell
VC-4
Capable for measuring of 1 - 3 ml of sample volume using electrodes with 6 mm of the diameter. Furnished holder prevents the vial from spilling.
-
product
Cell Stand
CS-3A
The CS-3A Cell Stand is adopted with CHI series Electrochemical Analyzers and other apparatus directly. The cell is enclosed in a Faraday cage to reduce electrical interference. A built-in gas control allows purging a sample. Gas line is provided to purge next sample, while analyzing the present sample separately, thus increasing productivity. Magnetic stirrer allows for controlling the mixing of the sample for experiments requiring mass transport of electrolyte or analyte to the electrode surface. Cell top positioner with detachable cell cap allows easy removal and replacement of the cell vial as well as the electrodes for rinsing, cleaning, and replacement.
-
-
product
Load Cell Transducer
Unitech Scales And Measurements Pvt. Ltd
Force can be measured by different methods, one of the most effective and accurate method is by using strain gauge based load cells. Four Transducer class strain gauges are bonded on the specimen and are connected in the form of Whetstone Bridge. The specimens are of different types depending on the requirement such as S, column, beam, ring, shear beam, binocular etc. UNITEH’S Load Cells are used for wide applications rite from commercial weighing scale to industrial process controlling, R & D applications and educational institutions. UNITECH’S manufacture load cells from 1Kg to 100Tons for compression or tension or universal (Compression and tension) applications. We also undertake custom built load cells for specific requirement and for OEM users.
-
product
Cell Solar Simulator
QuickSun® 130E
QuickSun 130E exceeds the ordinary Class A criterions of IEC904-9 ed. 2 with clear margin providing enhanced IV characteristics accuracy. The applicable test methods and procedures are inspected by SGS Fimko Ltd in order to guarantee the compliance and traceability not only with the above standard but also with IEC904-1 ed. 2 which specifies the IV measurement conditions.
-
-
product
Cell Isolation & Analysis
Life's complexity originates in cells, spanning cellular structure, genetic diversity, gene expression, and complex tissue formation. Serving as the fundamental unit, cells form the foundation of all biology. Characterization of cells, their processes and interactions can provide insights into areas like medicine, symbiosis, and biological diversity. Bio-Rad supports these inquiries, offering innovative technologies for your cell biology research.
-
product
Test Cell Measurement
Accurate Technologies’ long history in powertrain development provided insight into the day-to-day issues that were occurring during engine testing at a time when electronic devices were being introduced to monitor performance instead of traditional mechanical means. Outside of the harsh physical environments, devices used in these applications need to perform difficult high-voltage signal conditioning and high-speed synchronous pulse processing. ATI developed unique products that satisfy specific test cell or dynamometer challenges. These highly accurate products measure engine timing (IGTM) or speed (SmartTach) in convenient ways to provide information that otherwise may not be available.
-
product
Stimulus Test Cell
HA7200
The HA7200 enables these improvements by providing high-speed, high-accuracy temperature and pressure test for automotive sensor R&D and production. Advantest’s proprietary temperature control technology delivers an optimized test solution for high-spec pressure sensors across a broad range of temperatures, in the automotive industry and beyond.
-
product
Bulk Electrolysis Cell
This cell has been developed in order to perform a complete electrolysis. The carbon working electrode is a reticulaed form that provides with sufficient surface area to gain the rate in electrolysis.
-
-
product
Cell Testing
PEC offers a wide range of cell testers, starting from the 5A desktop test system (ACT0505), to our range of 50A cell testers for more standardized cycling (CT0550) and our advanced cell testers with capabilities up to 4000A (ACT0550). All systems support parallel switching for achieving higher currents.
-
product
Small Cells
5G small cells enable additional capacity and coverage to networks when and where needed – both indoors and outdoors. Our 5G protocol software for small cells supports both sub-6 GHz and mmWave bands and leverages the Small Cell Forum’s FAPI and nFAPI open interfaces to work seamlessly on our partners’ SoC-based small cell platforms.
-
product
load cell
EST-40
Technopark Automation & Control
The EST-40 is an 'S' type load cell suitable for use in tension and compression and is popular on hopper, tank weighing, belts scale and process weighing applications. It is low cost and is available in capacities from 50 kg to 2000 kg.
-
product
Compression Load Cells
A block that is designed to hold a load at one point to measure the compression. While tension load cells measure the pulling force, compression load cells measure a pushing force along a single axis.
-
product
Test Cells (
LaplaCell
LaplaCells provide a facility for the rapid and efficient testing of the EMC compliance of products. These cells offer a calibrated and screened environment in which radiated emissions can be measured and immunity to RF radiation can be tested. They \re calibrated according to the methodology of IEC61000-4-20, thus affording compliant testing to IEC61000-4-3 and pre-compliance testing for radiated emission testing.
-
product
Display of Energy Yielded by Photovoltaic Plants
VisiKid
It enables the direct conversion of sunlight into electrical energy through solar cells - that is why photovoltaics is one of the most popular sources of renewable energy; that is why solar power plants are increasingly being installed on the roofs of nurseries and schools. The aim is both to set an example and teach children about renewable sources of energy.
-
product
Photovoltaic Array Simulator, 15 kW, 1500 VDC
N8900APV Series
The PV simulators are autoranging, programmable DC power sources that simulate the output characteristics of a photovoltaic array under different environmental conditions (temperature, irradiance, age, cell technology, etc.) enabling you to quickly and comprehensively test inverter MPPT algorithms and inverter efficiency. The DG8900 SAS control software creates and downloads solar I-V curves to a single output solution. For multiple outputs choose the DG9000 SAS control software which can be used with up to 12 N8900APV sources.
-
product
Tension Load Cells
These Load monitoring systems are available in telemetry/wireless (RLP), self-indicating (LLP) and cabled non-indicating (WLP) versions. Towcell a 25kN, wireless tension load cell specifically engineered for the emergency services, salvage and 4 x 4 industries. Ruggedly built and highly accurate load link style load cell dynamometers allow for force and load monitoring across a broad range of industries and applications.
-
product
Scanning Droplet Cell
VS-SDC
Scanning Droplet System (SDC) uses a compact peristaltic pump to force electrolyte through a small diameter tube and into a specifically designed head. This PTFE-based SDC head is machined to allow electrolyte to flow past an installed Reference Electrode and then to a port at the base of the head.
-
product
Flow Cell Kit
QCMT
The quartz crystal microbalance (QCM) technique under electrochemical frequency is very useful to determine many compounds such as metal proteins, metal ions and thiol-conjugated oligonucleotides.
-
product
Load Cell Simulators / Testers
A load cell simulator is a handy tool during initial setup, particularly of a batching by weight scale. It replaces the load cell(s) in the system allowing the scale technician to simulate various weights that will trigger the outputs setpoints for activating valves, gates, and mixers. These products are a must for anyone involved in scale installations and repairs.
-
product
Telemetry Shackle Load Cell
TS-3.0
The DLM Telemetry Shackle is a high strength marine grade wireless Load Cell. Manufactured from industry leading Crosby and GN shackles along with a stainless steel load pin, the DLM Telemetry Shackle offers reduction in weighing headroom with the flexibility of 2.4GHz licence free wireless load transmission.
-
product
Shielded Test Cell
With an operating frequency starting at 10kHz, the Standard Test Cell (STC) creates an ideal environment for testing wireless devices for such technologies as GSM, UMTS, CDMA, Bluetooth, DECT, etc. Developed for the R&D, production and quality control environments where space is critical.
