Systems
are interconnected groups of purpose.
See Also: Equipment, Test Systems, System Integrators, System Test
-
Product
Low-leakage Switch Mainframe
E5250A
Mainframe
The Keysight E5250A low-leakage switch mainframe expands a single measurement station, such as the Keysight B1500A, 4155C, or 4156C, to an automated measurement system. Plug-in modules can be configured either as a cross-point matrix for general parametric measurements or as a multiplexer for long-term reliability measurements.
-
Product
Flex-plate Torque Sensing Systems
-
Advanced Telemetrics International
ATi’s FlexPlate Torque Sensing Systems permit in-vehicle Engine Output torque measurements.
-
Product
Antenna Masts
-
Antenna Masts are an integral part of EMC and RF measurement systems. Innco system masts are renowned worldwide as the standard benchmark. Available in manual or automatic, using either pneumatic and or electric driven, the antenna mast design has the capacity to carry antennas of 6kg (MM) and 10kgs (MA) as standard. Higher loads are available upon request.
-
Product
Ultra-High Vacuum Scanning Kelvin Probe
-
Our Ultra-high Vacuum Scanning Kelvin Probes (UHVSKP2020 and UHVSKP5050) give the user full access to work function (Φ) and contact potential difference (CPD) measurements under vacuum with the ability to scan a sample area of 20 x 20mm or 50 x 50mm respectively. Each system comes with the UHV head unit, tip amplifier (located at the mounting port), digital control unit and host PC with dedicated software. The tip can be retracted 100mm from the sample and approaches normal to the sample. The associated digital electronic unit powers the head unit and provides an interface between the head unit and the data acquisition system. The system comes with a complete user manual, which includes an introduction to work function measurements and a detailed description of the system software, including examples. The work function resolution of the Ultra-High Vacuum Scanning Kelvin Probes is 1-3 meV.
-
Product
14-Slot 32-Bit 6U CompactPCI H.110 Bus Backplane
cBP-6014R
Backplane
- PICMG 2.0 CompactPCI Specification R3.0 Compliant- PICMG 2.1 CompactPCI Hot Swap Specification R2.0 Compliant- PICMG 2.5 H.110 Computer Telephony Specification R1.0 Compliant- PICMG 2.7 Dual system Bus specificationR1.0 compliant- One system slot with 13 expansion slots, system on the middle slot of the backplane
-
Product
LCF3 Software
-
Provides system control, data acquisition, real-time graphs, calculation of results, storage of data to disk, and post test graphs and reports in accordance with the relevant sections of ASTM E606-04, BS 7270 (2006), and ISO 12106 (2003).
-
Product
Protocol Test System
USB Explorer 260
-
The Ellisys USB Explorer 260 is a sophisticated protocol test system for USB traffic monitoring, driver and software stack debugging, protocol compliance verification and performance analysis. Analyze USB 1.1 and USB 2.0 links at any speed, including OTG and the new InterChip-USB at all speeds and all voltages; emulate USB hosts and devices; inject pre-defined error patterns for stress and error recovery testing.
-
Product
Semiconductor ATE Systems
-
Our testers allow for the high-volume production of electronics that touch people’s lives in communication, safety, entertainment, and much more.
-
Product
Telephone And Line Analyzer
TALAN™ 3.0
-
The TALAN 3.0 Telephone and Line Analyzer represents advanced capability to detect and locate illicit tampering and security vulnerabilities on digital, analog, and VoIP telephone systems. New hardware provides the ability to test twisted pairs against modern telecommunication threats including shield and ground.
-
Product
Waveform Generators
Waveform Generator
Drive your test systems forward with PXI instruments from Astronics. Small size, power-packed, and cost-effective, these waveform generators provide the perfect upgrade for your test bench.
-
Product
Handling Technology - Board Handling
-
ENGMATEC offers an extensive standard program of efficient and proven handling systems.
-
Product
Bench Multimeters
-
Fluke Calibration meters have the precision and versatility to handle the most demanding measurements, on the bench or in a system. These instruments are easy to use and offer excellent value that makes them an ideal solution for many applications. Standards laboratory meters include: Reference multimeters; precision digital multimeters; bench multimeters
-
Product
TCSPC Lifetime Fluorometer
DeltaFlex
-
The DeltaFlex time correlated single photon counting (TCSPC) system is one of our Delta series of next generation time correlated single photon counting lifetime instrumentation. The DeltaFlex offers the ultimate in flexibility.
-
Product
PXI 8 Slot BRIC 240x8 1-Pole (8 sub-cards)
40-561A-121-240X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
-
Product
Mobile Vehicle Surveillance System
MVSS
-
The MVSS is a rugged, multi-spectral mobile surveillance system that provides rapid deployment and unmatched maneuverability. Multiple sensor packages along with command and control software are integrated into an industry tested vehicle, transforming the cab into the command center. Available in multiple range configurations, MVSS can also network its sensors with other Teledyne FLIR vehicles and command and control nodes. It's the most trusted mobile, long-range perimeter security system available.
-
Product
PXI Test Instrumentation
-
The Yelo Pixi general purpose tester is a PXI based functional test system with in-circuit and continuity capability. Built into a free standing 19” rack is a PXI chassis, mass interconnect fixture interface, PC, flat screen and space for additional user selectable instrumentation.
-
Product
UV Absorption O3 Analyzer
Model T400
-
Teledyne Advanced Pollution Instrumentation
The Model T400 UV Absorption analyzer uses a system based on the Beer-Lambert law for measuring low ranges of ozone in ambient air.A 254 nm UV light signal is passed through the sample cell where it is absorbed in proportion to the amount of ozone present. Periodically, a switching valve alternates measurement between the sample stream and a sample that has been scrubbed of ozone. The result is a true, stable ozone measurement.
-
Product
Voltage Controlled Oscillators
-
Teledyne RF & Microwave offers Voltage Controlled Oscillators (VCOs) utilizing bipolar transistors & silicon varactors over the frequency range of 40 MHz to 18GHz. Many of the VCO designs incorporate internal filtering, regulation & amplifiers to meet total system requirements in a small integrated package. Additionally, our hermetic hybrid designs can be screened to the most demanding military and space applications.
-
Product
Database Performance Analyzer
-
Monitor and optimize multiple database management system (DBMS) platforms for cloud and on-premises environments.
-
Product
Spectroradiometer
-
Designed to have a capability of producing any visible spectral distribution, mimicking various light sources in the visible region by feedback control of the radiant power emitted by individual LEDs. This LED test system will be used as a transfer standard for photometric, colorimetric and radiometric applications.
-
Product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
Laser Board
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
Product
Electricity Meter Test Equipment
-
The Reference Standard RS is precision standard meter in single- and three-phase version for electrical power and energy measurement. It is designed to meet all requirements put on a reference standard in a single- and three-phase electricity meter testing and calibration systems. The Reference Standard can be set to any true or artificial mode of operation in three phase system and is capable to evaluate individual quantities in any phase
-
Product
PACHYMETER
MS 1305
-
This unit is used to measure the distance between Retina and Lens. System has continuous and single mode measurement provision. It also has Lasik Mode and test mode. Up to 8 eye maps can be programmed.
-
Product
LXI High-density 896x4, 2A Matrix
60-553-007
Matrix Switch Module
These high-density single pole LXI matrix modules are capable of switching up to 150VDC/100VAC, or 2A (60W max). The use of high-quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
Product
PXI 8 Slot BRIC 30x32 1-Pole (6 sub-cards)
40-562A-121-30X32
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Bus Digital-Synchro-Resolver
PC104
ITA
Computer Conversions Corporation
The PC104-DS Series are Low Cost, Dual Channel, PC104 Compliant Digital / Synchro / Resolver Output Cards designed to simulate precision AC Synchro and resolver formatted signals for use in navigation and positioning systems or test sets on both industrial and COTS - military type applications.
-
Product
X-ray and CT inspection System
UX20
-
Due to the transformation to electric mobility, foundries are increasingly producing larger and more complex components. With its exceptional inspection envelope and the smart Geminy software, the UX20 facilitates fast and precise inspections of cast parts and helps increase overall production efficiency.
-
Product
Low Cost Solar Simulators
-
Abet Technologies model 10500 is a low cost solar simulator providing an attractive alternative to more fully featured and expensive solar simulators for applications that do not require a large area illuminated field. The optical system of the 10500 produces a collimated 25 mm beam. Focus or defocus it for higher irradiance or larger solar cells. One sun output is achievable up to a 35 mm diameter illuminated field.
-
Product
Qseven® Reference Carrier Board
Q7-BASE
Carrier Board
Qseven is a Computer-on-Module (COM) standard for small sized and highly integrated systems adopted by SGET. The Qseven concept is an off-the-shelf, multi-vendor, Computer-on-Module that integrates all the core components of a common PC and is mounted onto an application specific carrier board. Qseven modules have a standardized form factor of 70 mm x 70 mm or 40 mm x 70 mm and have specified pinouts based on the high-speed MXM connector, regardless of the vendor. The Qseven module provides the functional requirements for an embedded application, which include, but are not limited to, graphics, audio, mass storage, network and multiple USB ports. A single ruggedized 230 pin MXM connector provides the carrier board interface to carry all the I/O signals to and from the Qseven module. This MXM connector is a well-known and proven high-speed signal interface connector that is commonly used for -PCI Express graphics cards in notebooks.
