Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
Product
Optics Test Systems
Contract Measurements And Services
-
Optik Elektronik Gerätetechnik GmbH
Thanks to our very good laboratory equipment, we offer contract measurements for numerous measuring tasks. In the field of optics, measurement and testing technology, these are, for example, the parameters MTF, focal length, radius, contact dimension, focal length, geometric and optical parameters of cylindrical lenses. Others on request.
-
Product
Hand-held Tachometers
-
SHIMPO offers a wide range of hand-held tachometers that measure the total number of revolutions of a shaft or number of pulses of reciprocating equipment. Our models can measure and record last/min/max and up to 10 reading using up to 16 different units of measure. Our tachometers are designed for applications such as Motor Speed/Conveyor Speed/Fan Speed/Length Measurements that measure rpm of motors or shafts, either contact or non-contact with Laser style combination tachometer.
-
Product
RJ45 Port Saver
#21025C
-
Extend the life of your tester by using the RJ45 PortSaver as your sacrificial cable. Eliminates the wear and tear from constantly plugging in and out of the tester port and minimizes the risk of damaging the RJ45 jack if the connector contacts are not crimped completely. Compatible with all Platinum Tool testers with built-in […]
-
Product
Variable Power Supply
VS3
-
The VS-3 power supply is a very convenient portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 3 amps, thus the name VS-3. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-3 is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case. A unique feature of the VS-3 is that it contains “Magnet Packs” on the back of the case. These “Magnet Packs” can support the VS-3 and allow it to “hang” from any magnetic metal surface. The VS-3 can be powered by our UPS system, eliminating the need for an extension cord. The ability to magnetically attach the VS-3 near the source of connection and eliminating the need for an extension cord makes the VS-3 a “must have tool” for technicians.
-
Product
Portable Optical Pickup
OP200x
-
Power Measurement Technologies Inc.
The OP200x is a versatile, lightweight, portable instrument designed to detect watt-hour meter disk rotation, light pulses, LCD segments and contact closure events.
-
Product
Dual 12x4 1-Pole High-Density PXI Matrix Module
40-520-405
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
Testing Services
-
Koehler Instrument Company, Inc.
A complete source for your testing solutions, Koehler offers a wide range of in-house testing services based on selected standard test methods. Our staff is comprised of technical experts and the best instrumentation for fast, accurate and reliable results. We specialize in all tests for which we offer instrumentation as well as additional test methods. You are invited to send us samples for testing and evaluation at any time. Please contact your Koehler representative for additional information.
-
Product
GPIB to Relay Interface Boards
Model 4864 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
Product
Solder Test Pallet
WaveRIDER® NL 2
-
The wave soldering process is one of the most challenging procedures to set up. The ECD WaveRIDER NL 2 greatly simplifies wave solder set up and ensures perfect repeatability, time after time. Board recipe preheat temperatures, conveyor speed, wave height, contact times and parallelism are all measured and monitored using the WaveRIDER NL 2 process pallet.
-
Product
Current Clamp Adapter
-
PeakTech Prüf- und Messtechnik GmbH
It uses a pair of jaw which allow clamping around an electrical conductor to measure the current in a conductor without the need to make physical contact unlike a normal multimeter.
-
Product
PXI Single 16 Channel Switch Simulator
40-485-221
Switch Module
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Syringe Pump Options and Accessories
-
Options and accessories for SyriXus pumps allow you to customize your pump to meet the unique needs of your specific application. Most options are available to be retrofitted on-site, or installed in the factory, if your needs change. Contact the factory for assistance with selection and ordering.
-
Product
Door Contact Sensor
ENVIROMUX-M-DCS
-
Monitors access with a magnetic bridge sensor, which responds to any magnetic material (no special inserts necessary). Can also be used for monitoring side wall and covers. Includes mounting hardware. For normally closed circuit connection. 2-wire interface. Screw terminal. Maximum cable length: 1,000 ft. Wide actuating gap, approximately 1". Dimensions WxDxH (in): 0.5x0.5x2 (Switch), 0.5x0.5x2 (Magnet). Operating temperature: 32 to 158°F (0 to 70°C). Regulatory approvals: RoHS.
-
Product
Contact Resistance Meter
CRM 200B+
-
CRM directly measures micro-ohm values at 200A DC under live EHV switchyard conditions quickly & accurately. It is specially designed to reliably measure micro-ohm contact resistances of Circuit Breakers, Isolators, Busbar joints, earth switch joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards up-to 765 kV. SCOPE’s ability to make electronics work in such environment enables CRM to measure mili-volts signal in the presence of kilo-volts noise.
-
Product
Miniature Instantaneous Relays
CU-D Series
-
Heavy duty miniature power relays for demanding applications, switching of AC&DC voltages, resistive and/or inductive loads. Equippedwith weld no transfer contacts.
-
Product
Non Contact Voltage Detection
-
Our range of Non Contact Voltage Detectors offer a safe and accurate method of checking for voltage present on a conductor. With audible and visual indication, our range offers total confidence when checking cables for live voltages
-
Product
Uniform Light Sources - Unique And Specialist Configurations
-
We ware experts for custom integrating sphere light sources for specialist applications and for use in demanding environmental conditions. Please contact us with your specific request.
-
Product
Complete Probe Station
BD Series
-
Best for DC and RF probing, the platen lift is designed for smooth raise and contact of your probes simultaneously to your device. It is ideal for probing multiple spots on your device, or through multiple devices.
-
Product
Data Acquisition Module for Embedded Systems with IO60 expansion
IO60-M410
Data Acquisition Module
WINSYSTEMS’ IO60-M410 is a reliable data acquisition module for embedded systems with IO60 expansion featuring 24 GPIO (General Purpose Input-Output) tolerant to 30 V DC. Activity LEDs indicate device communication and DAC fault. WINSYSTEMS can provide custom configurations for OEM clients. Please contact a Applications Engineer through our contact page for details.
-
Product
Shock Absorber Tester
-
Maschinenbau Haldenwang GmbH & Co. KG.
Display on LON analog displays with theEvaluation in "Lehr''s damping factor" or damping ratio "D"Fully automatic testAutomatic test start after bilateral plate load of more than 60kgFrequency controlled drive excitation by electric motors to determine the maximum vibration amplitude with subsequent evaluation of the axle dampingrunning underbody as self-supporting frame constructionParallelogram guided test plates, thus no fixed wheel contact requiredgalvanized version
-
Product
TriPaddle Signal
-
TriPaddle signal contacts achieve superior performance using VPC's patented TriPaddle design. Rated up to 20,000 cycles Carries up to 7 amps (22 AWG ) or 10 amps (14 AWG) continuous Resistance is 4 mOhms max
-
Product
48-Channel VME Isolated Digital Input Module
V280
-
The V280 is a single-wide, 6U VME module that includes 48 isolated logic inputs. It is available in versions for nominal 5 volt or 24 volt input levels. The V280 has independently programmable rising and falling edge response times to support contact debounce, glitch catching, and DC or AC inputs.
-
Product
Combinated Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Measure small direct and alternating currents up to 2 A with 1 mA resolution. The device measures the current indirectly via the surrounding magnetic field, so it is measured without contact when the clamp jaws enclose the current-carrying conductor (single wire).
-
Product
Vision Measuring System
-
CNC Vision Measuring System. Supporting non-contact and contact hybridContact measurement of detailed shape is achieved by extra small stylus with minimum diameter of 15um
-
Product
Plugbord
3662-5
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
Product
Mini Coax, Contact, Receiver, Right Angle for PCB Mounting
610104160
Coax Contact
For use with VPC Module 510104319.Primary mating contact 610103136. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination PCB TH SolderInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 1 GHzVSWR 1.445 @ 1 GHzInsertion Loss -0.885 db @ 1 GHzDWV 1500 VDC min.Contact Resistance 5mΩ max.Environmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
-
Product
Ethernet Digital Interface
Model 8063
-
* Provides 48 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes or data strings.* Transparent data transfer mode.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* 1 U high rack mount kit mounts one or two 8063s.* Includes 100-230 VAC Power Adapter with universal plugs.
-
Product
RF Microwave Switching
Keithley S46
-
S46 and S46T Microwave Switch Systems are designed to simplify the automated switching needed to test a wide range of RF and telecommunication products and devices. The S46 can control 32 relay contacts in a package as small as a 2U high (3.5 in) full-rack enclosure. Choose the System 46T if your application requires a terminated configuration. It builds on the design technology of the unterminated System 46. The System 46T accommodates up to eight terminated SPDT coaxial microwave relays and four terminated multi-pole coaxial microwave relays.
-
Product
Replacement Protective Cover, I1, Receiver
310113524
Protective Cover
The receiver protective cover is designed to protect your modules and contacts while the test system is not in use. A protective cover is included with the i1 Receiver.
