Clamps
-
Product
Clamp Earth Tester with Bluetooth Connection
MET-10X
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Next clamp-type grounding resistance tester that can connect to a smartphone via Bluetooth and save data on an our cloud server.
-
Product
Earth Ground Tester
1625-2
-
The Fluke 1625-2 earth ground tester measures earth ground loop resistances using only clamps, only stakes, or one clamp and stakes. With the stakeless test method, the Fluke 1625-2 is able to measure earth ground loop resistances for multi-grounded systems using only current clamps. This technique eliminates the dangerous, and time consuming job of disconnecting parallel grounds, and finding suitable locations for auxiliary ground stakes.
-
Product
Leakage Clamp Meters
-
Precision Mastech Enterprises Co.
Specialized, high-sensitivity electrical testing tools designed to measure low-level AC current (typically in milliamps, to detect ground faults, insulation failures, and potential hazards without disconnecting equipment
-
Product
Enclosure, G10, 3 Cable Clamps, 4" Depth
410114138
Enclosure
Enclosure, G10, 3 Cable Clamps, 4" DepthThis G10 enclosure includes 3 adjustable U-shaped cable clamps that allow a maximum cable bundle of 1.59 sq. inches per clamp. ITA strain relief plates are not needed.Housing: Material = .06" Aluminum, Finish = Powder Coat Black
-
Product
Flexible Clamp Meters
-
TES Electrical Electronic Corp.
Three current ranges. Two output sensitivity measuring instruments. Input protection up to 600V. Suitable for any electrical system. Wide bandwith low phase shift.
-
Product
Portable Three-Phase Energy Standard
PEWM-3C
-
The three-phase energy standard PEWM-3C is used for quick on-site tests of all types of electricity meters – for active, reactive or apparent energy, two-, three- or four-wire connection. Three voltages and three currents are measured at the same time. The current can be measured either via direct connection up to 10A (class 0.1), or with three current clamps (CC) to 120A, 150A or 1000A (class 0.2).
-
Product
Low Current Probe/DMM
687
-
With the capability of measuring down to 1 milliamp (.001A), the #687 is a great tool for all low current applications. Especially for diagnosing parasitic drains! Clamp opening is large enough to fit over most negative battery cables. Applications: fuel injectors, fuel pumps, electric motors, battery drains, charging systems.
-
Product
Multi-Featured Clamp Meters
-
Amprobe’s multi-featured clamp meters cover a broad range of industrial, HVAC and electrical applications.
-
Product
Standard Clamp Meters
-
For extreme temperatures, choose an analog clamp meter that can measure amps and volts without needing batteries.
-
Product
AC/DC Clamp Milliammeter (CE)
M-740
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High sensitive for low range leakage current*Suitable for measurement of 4-20mA DC controlled circuit*DC mV analog signal output*Lowest influence from Magnetization and Terrestrial magnetism*Wide measuring ranges - up to DC 1000mA and AC10A
-
Product
Flex Clamp Meters
-
Flex Clamp Current Probes expand existing meters. Compatible with most meters using universal banana leads. Flexible Coil adds accessibility - easily maneuvering around cables that are in hard to reach areas and large enough to thread around larger conductors.
-
Product
Digital Clamp Tester With 80mm X 74mm CT80mm X 74mm CT, ACA
MCL-800D+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・80mm x 74mm CT window and wide current measurements from 0.01mA to 1000A.・With filtering switch (which cuts currents above 150Hz)・Maximum value hold / Data hold function available・Auto range switch that selects the optimum range according to the measured value・Easy to read large display
-
Product
Sensor Unit for High Precision Current Sensors
CT9557
-
Hioki pull-through current sensors and clamp on current probes are best-in-class current sensing devices for use with power meters, Memory HiCorders and high performance oscilloscopes. The CT9555 is 4-channel sensor unit and power adapter for any of the CT686x series, 9709 and CT684x series current sensors and probes that provides waveform and RMS output.
-
Product
9-Pin D-Type Connector Block
40-965-009-F
Connector Block
Suitable for use on the front of modules this connector block provides a simple method of connecting to 9-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
Product
C/I Clamp Meters
CLAMPMETER,400A AC (CM-330)
-
*AC current measuring capability up to 400 amps*Compact size, fits easily into tool pouch*Data hold and Max hold to capture important readings*2000-Count LCD*Lifetime Limited Warranty*Accessories included: (1) 9V battery, carrying case*Lifetime Limited Warranty
-
Product
Ammeter According to DIN EN 61010-1 (VDE 0411-1)
-
PeakTech Prüf- und Messtechnik GmbH
Is a measuring device for AC and DC currents up to 1000 A using a current clamp for conductor diameters up to 48 mm. Current and voltage measurements are carried out as true RMS (true rms value) measurements, which means that the measured values are displayed correctly even with waveforms that deviate from a sine wave.
-
Product
Rackmount Kit For Infiniium EXR-Series, 8U
EXR2RACK
Mounting Kit
The EXR2RACK rack mount kit includes all parts needed to mount your Infiniium EXR-Series oscilloscope in an 8U open frame rack and includes a Support tray, Trim plates, BNC connectors to be inserted into the bottom trim plate, black rubber stoppers to plug holes in bottom trim plate if the hole is not being used for a BNC connection, Two track rails, Two clamp brackets, both right and left Top clamp brackets, screws, and nuts.
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-140
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of feeder*Compact size*AC 1mA～300A
-
Product
Test Equipment
Digital Clamp Meter
-
Is a large AC current digital multi clamp meter, integrated with 2000 Count, True RMS, auto and manual measurement, air-cored coil sensing technology.
-
Product
Digital Circuit Tester 3-30V
29050
-
The probe is insulated to prevent the possibility of shorting the side of the probe to other components. 47" cord and heavy-duty alligator clamp for secure connections.
-
Product
Clamp Meter 6000counts Ture RMS
VA312 /VA315
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Clamp meter Diode Test Auto Range Continuity Buzzer MAX/MIN Value Measurement.
-
Product
Clamp Meter AC/DC TRUE RMS CLAMP METER
VA316
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Clamp meter 3999 counts DC/AC clamp meter Autorange DC and AC clampmeter up to 1000A ,42 segment.
-
Product
ITA, iCon, Extended Cable Clamp
410123115
ITA
This iCon ITA includes an extended cable clamp to accommodate larger cable bundles. The maximum cable bundle area = 1.97 " sq. or a 1.58"/40.13mm diameter bundle. The clamp may be inverted for smaller cable bundles.Please note: This ITA does not offer an increased bend radius that may occur with a larger cable bundle radius. Larger bend radius is offered by the iCon XL, p/n 410123232.
-
Product
Ultra-Low Frequency Workstation
MK52 Series
-
Providing Ultra-Low Frequency levels, the MK52 Series offers the ultimate low natural frequency performance for a wide range of high resolution instruments, such as analytical balances, cell injection, confocal microscopes, patch clamping, optical microscopes, wafer probing, sensor calibration, atomic force microscopes and other sensitive equipment requiring high isolation efficiency.
-
Product
Sensor Clamps
ULP-CP
-
Use a single clamp for the Sensor with a single #10-ANSI screw for one-hole fixing.
-
Product
Configurable CAN FD Module With A Focus On Analog I/Os
PCAN MicroMod FD Analog 1
-
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The motherboard PCAN-MicroMod FD Analog 1 focuses on analog inputs and outputs, which are provided with the appropriate protective circuit.
-
Product
1000 Amp AC Digital Clamp Meter
DL6401
-
This clamp meter offers many features in addition to basic current testing. The slim design combined with the tear shaped jaw makes it an ideal unit for use in crowded panels and tight spaces.The data hold and peak capture function makes this a versatile and cost effective clamp meter.
-
Product
Enclosure, G18, Hinged Cover, 3 Cable Clamps, 7" Depth
410112664
Enclosure
Enclosure, G18, Hinged Cover, 3 Cable Clamps, 7" DepthIncludes hinged cover, handles and 3 cable clamps- allow a max. cable bundle of 1.59 sq. inches per clamp. ITA strain relief plates. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-340L
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-80H
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High precision clamp type ZCT sensor*Big CT window,φ80mm*AC 0～10A*Least affection from the external magnetic field and residual current
