Clamps
-
Product
Battery Load Tester
MD4260
-
Test capabilities: Battery voltage, battery cranking, battery charging volts and good/bad battery test. Test batteries on and off the car in just 30 seconds. Heavy duty copper-plated clamps. Internal loaded unit with a 100-amp load capacity. Load safety switch to prevent arcing. For 6- and 12-volt batteries.
-
Product
1000A Power Quality Clamp Meter with Temperature
ACD-41PQ
-
The Amprobe ACD-41PQ provides a simple and effective way to verify if the electrical system is affected by harmonics. Add on troubleshooting capabilities with the ACD-40PQ data-logging feature or get complete power analysis with the ACD-41PQ. Increase measuring efficiency with an optional PC interface kit.
-
Product
Heavy-Duty Circuit Tester With Grounding Adapters
30610
-
Heavy-duty circuit tester with multiple options for connecting to a ground source. Long, 12’ cord has a quick coupler to securely connect clamp or power outlet plug. Large, strong clamp connects securely. Power outlet plug can always be used to provide ground in the cabin. For testing circuits up to 12 volts.
-
Product
Mini 80 Amp AC/DC Clamp Meter
DL6506
-
A compact clamp meter for use where access to cables is a problem. This instrument fits neatly in the hand and with a clamp opening of 18 mm it is ideal for those instances where it is hard to reach cables.
-
Product
Inductive Clamp for 41821 and 41822 Digital Meters
-
Spare inductive clamp for 200 and 300 range multi and clamp meters.
-
Product
IEC60068-2-75 Spring Impact Hammer
-
Shenzhen Chuangxin Instruments Co., Ltd.
Adjust the impact severity by rotating the knurled cap until the desired energy- value is displayed. Pull the knob slowly out of the device until it locks in place. If moved too fast, the clamp may skip its arrester and will lock at its way back when the pulling-force declines. Hold the device horizontally at it’s housing tube and press the (black) release cone to the specimens plane of impact. The strike is automatically released when the release force threshold is reached.
-
Product
AC/DC Mini Digital Clamp Tester
M-230+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
23mmφCT window and ultra compact size. Data-hold function. Especially useful when working in dark or hard to get areas. Accurate gearing mechanism for closing of CT. Best tool for automotive service.
-
Product
AC/ DC mA Current Clamp-on Transducer
CA-60
-
This miniature clamp meter features two Hall effect sensors. For use with any multimeter with 200mV or/and 2V ranges for direct readout input impedance of least 1M ohm. High conversion factor for low DC and AC mA measurement. With the small jaw size it can fit into tight space in circuit panel or wire bundle to take the reading.
-
Product
Clamp-on Testers
-
With our 16 models of different clamp-on testers, Yokogawa provides the right tool for the job. Our CL Series consists of AC, AC/DC, and leakage current clamps with various ranges and dimensions. The multiple options include RMS, Mean, Temperature, frequency, and recorder output.
-
Product
37-Pin D-Type Connector Block
92-965-037-F
Connector Block
This connector block provides a simple method of connecting to 37-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
Product
Special Application Digital Clamp Meters
-
Precision Mastech Enterprises Co.
Specialized electrical testing tools designed to measure current and other parameters in specific environments or for unique, non-standard tasks that standard clamp meters cannot handle efficiently.
-
Product
Clamp-on DC Meters
-
The Swain Meter™ Company manufactures portable clamp on DC ammeters that precisely measure the magnitude and direction of DC current flow on any conductor. Used both onshore and offshore, Swain DC clamp on amp meters accurately read current from 5mA to 200 Amps with a resolution of 1mA in the 0-2Amp range.
-
Product
ATEX / FM Approved Grounding Clamps, Cables and Reels
Cen-Stat Static Grounding Clamps
-
Static grounding systems like the Earth-Rite range combine interlock control and visual indication to verified ground connection points and offer the highest levels of protection over electrostatic ignition risks. However, equipment specifiers may select passive grounding devices, like single pole clamps, to ground and bond plant equipment.
-
Product
Electrical Test & Measurement Products
-
Electrical Test & Measuring Products, Including Clamp Meters, Voltage Testers, Multimeters & Test Kits
-
Product
160-Pin DIN41612 Shielded Connector Block, Male
B1604MR-4F-0A
Connector Block
This connector block provides a simple method of connecting to high density DIN41612 connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
Logger with Current Clamp0.15 to 200A
TGP-4810
-
A data logger, housed in a rugged case, supplied with a Chauvin Arnoux Current Clamp . This unit is ideal for mains and power consumption monitoring.
-
Product
Total Nitrogen and Sulfur Analyzer
XPLORER-NS
-
The XPLORER-NS was developed as a total nitrogen/total sulfur combustion analyzer, capable of handling fully automated applications for liquids, solids, and gases (including LPG samples.) Changing from the liquids & gas module to the solids module has never been easier. Just push one button and the liquids module is automatically retracted from the heated zone. No clamps or manual locks required.
-
Product
Residential/Commercial Combustion Analyzer
C165+
-
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C165+ Residential/Commercial Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and differential pressure. Prints to optional printer and wireless App. The new LINK feature connects the included wireless pipe clamp temperature probes and other optional probes to the C165+. Essential information for installing and maintaining furnaces and boilers all in one device.
-
Product
25-Pin D-Type Female Connector Block
92-965-025-F
Connector Block
This connector block provides a simple method of connecting to 25-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross-sectional area and insulation properties.
-
Product
High Insulation Digital Clamp Tester
HCL-3000D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide AC current measurements for 0.001A～20A.*Easy operation, Push to Open and Pull to Disconnect Mechanism.*Safe AC current measurements for high voltage circuit (AC80 to 7000V).
-
Product
Flexible Clamp Meter 10 inch
FLIR CM55
-
The FLIR CM55 is an ergonomic tool designed to simplify difficult current measurements. Made with a narrow, 10-inch (25.4cm) flexible coil clamp, the CM55 lets you easily take measurements in tight or awkward spots— a difficult task with a traditional hard jaw clamp. With Bluetooth® communication for remote viewing and data transfer to iOS® and Android™ devices via the FLIR Tools Mobile app, you can analyze and share data fast right from the jobsite.
-
Product
Wireless Connectivity AC Clamp Meter with 4000 count / NCV / SPT / Max. 400A AC Current
MS-W364
-
This is a external wireless connectivity Digital Clamp Meter with 4000 Count, True RMS, auto and manual measurement.
-
Product
Clamp Meters
-
Amprobe invented the first clamp meter in 1948 and has continued to innovate and evolve. Today Amprobe offers several categories of clamp meters – from the rugged CAT IV rated Navigator Series, to the versatile Swivel clamp meters, to the compact mini-clamps. Whether you work on residential, commercial, or industrial applications you’ll find an Amprobe tool that fits your needs.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-40
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～600A*Current measurements of feeder
-
Product
Digital HVAC Clamp Meter w/ CATIV 300V
DL379B
-
UEi Test & Measurement Instruments
Digital HVAC Clamp meter with dual level NCV and CATIV 300V rating
-
Product
Vertical Measuring Projector
-
Sinowon Innovation Metrology Manufacture Ltd.
The lifting system adopts cross roller rail and precision screw drive, which makes lifting drive more comfortable and stable; Coating process reflector, clearer image and great dustproof; Adjustable contour and surface illumination, to meet with difference workpiece demand; Imported high light and long using life LED illumination ,to ensure precision measurement demand; High resolution optical system with clear image and magnification error is less than 0.08%; Powerful Bi-axial fan cooling system，highly increase using life; Powerful and colorful DRO DP400，realized fast and accurate 2D Measurement; Built-in Mini-printer, can print and save data; With standard 10X objective, optional 5X,20X，50X，100X objective，rotary table, foot switch ,clamp, etc.
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-30
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of feeder*Compact size*AC 1mA～100A
-
Product
Universal Clamp Tester
M-310
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
The unique U type CT enabled to measure the load current of single or three phase cable without separating the cable to the wires. Leakage current measurements with least affection from the external magnetic field. Wide current measurements.(AC0.01mA-300A)
-
Product
Elongation Tester
SC-5
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.3-2008Used to test elongation (ductility) of copper wires covered with φ0.100-3.0 mmenamel, silk or other insulation materials and other metal wires with tensile strength ≤2000N;Application of SCM control allows for fast operation and strong anti-interference capacity;Preset elongation of samples with two-digit toggle switch and, when the preset value is reached during test, motor and counter would automatically stop action and display results;The instrument is capable of measuring elongation while also the tensile force and holding the maximum tensile force value during stretching;Clamps are designed according to characteristics of various wires to prevent samples from breaking at clamp jaws, easy to load samples and, after samples are compressed, enamel can be automatically broken;While sample is broken, movable clamp would automatically stop moving, with error between displayed and actual elongation value less than 1%;
-
Product
CTEK Battery Analyzer
56-925
-
The CTEK BATTERY ANALYZER tests with high accuracy the condition of all types of 12V lead-acid batteries including Wet, Maintenance Free, Ca/Ca, Gel and AGM. Easy to use it provides fast, and easy to understand results. Operating voltage range is 8–15V with a test range of 200–1200EN. Simply connect the clamps to the battery and follow the step by step instructions on the display.
