Cages
-
Product
Fiber Optic Connectors & Cages
-
Pulse Electronics Networking BU supplies high-quality fiber optic connectors and cages to innovative ODMs, OEMs and other manufacturers designing today’s most demanding network products. Our line of 40+ fiber optic connectors include SFP, SFP+, and QSFP connector and cage products.
-
Product
Faraday Cages
-
LBA's EMFaraCage® faraday cages are EMI and RFI shielding boxes and RF test enclosures that bring convenience to device testing. Faraday cages are ideal for isolating critical systems in high field RF environments or wherever RF ingress or egress must be minimized. Security, production testing, biomedical research and semiconductor testing are only a few of the many areas where EMFaraCage® faraday shielded enclosures are employed. EMFaraCage® faraday cage enclosure systems are fully featured to support a wide variety of test missions. The standard faraday cages include effective power, dataline and RF signal isolation in large test volumes. EMFaraCage® faraday cages are much more affordable than shielded room solutions and offer the convenience of portability.
-
Product
CPCI Test Extender 6Ux400mm
117EXT6116-0XXX
-
The cPCI extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged on each 2mm HM connector in P1-P5. Each line in rows A-E can be isolated with the DIP switches.
-
Product
Connector Block, 50-Pin D-Type, Female
40-965A-050-F
-
The 40-965A-050-F connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
9-Pin D-Type Connector Block
40-965-009-F
-
Suitable for use on the front of modules this connector block provides a simple method of connecting to 9-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Type 12R2, 8U, 19" Rackmount, MIL-Rugged, Top Load
12R2-8U-TL
-
The 8U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
Product
Type 12R2, 5U, 19" Rackmount, MIL-Rugged, Horizontal
12R2-5U-H
-
The 5U, 12R2 is designed to meet the harsh environments of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
Product
Type 12R2, 10U, 19" Rackmount, MIL-Rugged, Vertical
12R2-10U-V
-
The 10U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
Product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
-
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Type 12R2, 14U, 19" Rackmount, MIL-Rugged, Vertical
12R2-14U-V
-
The 14U, 12R2 was designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs.Shock isolated versions are designed to attenuate 25G shock to the chassis to less than 10Gs at the card cage and PSU tray.
-
Product
DC Coreless Motor
-
Adamant Namiki Precision Jewel Co Ltd.
There is a structure in the cage shape by only the copper wire turns around a cylindrical permanent magnet placed inside It is a feature. There There is not an anron core, it does not receive the action of the copper basket type rotor is light, the moment of inertia becomes small, so quick response is possible. A Permanent Magnet, There Is No Cogging, That Is, Rotation Is Smooth, And Vibration And Noise Can Be Reduced. - Since Rare Earth Magnets With High Magnetic Properties Are Used And The Rotor Is Formed Only With Coils, The Motor Itself Can Be Made smaller and lighter.
-
Product
200-Pin LFH Connector Block, Female
B200LFR-2F-5B
-
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross sectional area and insulation properties.
-
Product
Connector Block, 78-Pin D-Type, Female
40-965A-078-F
-
The 40-965A-078-F connector block provides a simple method of connecting to 78-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell.
-
Product
9-Pin D-Type Connector Block
92-965-009-F
-
This connector block provides a simple method of connecting to 9-Pin D-Type connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage.
-
Product
160-Pin DIN41612 Connector Block, Female
92-965-160-F
-
This connector block provides a simple method of connecting to high density DIN41612 connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
Product
Highly Dynamic XY Linear Motor Scanning Stage
L-731
-
Physik Instrumente GmbH & Co. KG
The magnetic linear direct drive is designed to provide high velocity and acceleration for inspection and microscopy. With a travel range of 205 mm square and solid velocity to 100 mm/sec, the L-731 is equipped to deliver high accuracy and smooth motion. Precision crossed roller bearings with anti-creep cage assist enable superior guiding accuracy (1.5 m straightness for loads up to 20 kg). An integrated optical reference encoder and limit switch provide further positioning control and accuracy for this compact stage with 5 nm resolution. DC servo motor versions are available on request.
-
Product
Airlock Control System
-
The system is built on the basis of a panel computer with a touch screen, performing the functions of a user interface and recording the measured parameters. The stand is equipped with gate drives and a set of sensors (pressure, flow rate, force). Real-time gate control is implemented on the basis of the R-series board; for input and conversion of analog signals from the sensors, an expansion cage of the cRIO-9151 R-series boards is used.
-
Product
200-Pin LFH Connector Block, Female
B200LFX-2F-5B
-
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross sectional area and insulation properties.
-
Product
6-Slot Backplane Card Cage
IPC-6006
-
Open-frame card cadge for embedded system, Shockproof hold-down clamp design. Support 6-slots full size and half size SBC, Support one PS/2 power supply, one 3.5" HDD and one cooling fan.
-
Product
96-Pin Micro-D Connector Block, Female DIN Rail Mounted
40-966-096-F
-
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
68-Pin VHDCI Connector Block, Female Without Backshell
B068VFX-6F-0A
-
This connector block provides a simple method of connecting to high density 68 Way VHDCI connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
RF Shielding Services
-
LBA offers complete architectural RF shielding capabilities, including RF shielding for communications, medical and other radio frequency interference sensitive facilities. LBA is a major provider of architectural shielding solutions for buildings, laboratories and other spaces. LBA also offers other RF shielding materials, such as paints, fabrics and faraday cages, as well as an integrated line of shielding components to provide a comprehensive shielding system.
-
Product
Impulse Current Measuring Shunts
ICMS
-
The Impulse Current Measuring Shunts ICMS are new designed tubular shunt types with best response behavior to match the high performance of the TR-AS digital recorder for comparative current measurements. A 1st partial response time less than 10ns and a settling times less than 20ns show the advantage of these shunts. They show no initial overshoot peak, no oscillations and do not need compensation box to optimize the transient behavior as known from e.g. cage shunts.
-
Product
96-Pin Micro-D Connector Block, Female With Backshell
44-965-096-F
-
This connector block provides a simple method of connecting to high density 96-Pin SCSI Style Micro-D BRIC connectors. The screw terminals accept wires up to 20 AWG and use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
Rodent Behaviour Measurement System
LABORAS®
-
LABORAS is a high throughput system for automated recognition of a large number of rat and mouse behaviors. LABORAS is completey non-invasive, uses a home cage environment and automatically determines accurate and consistent behavioral data without the need of human observers. In addition LABORAS calculates precise position tracking parameters.
-
Product
68-Pin SCSI Micro-D Conn Block DIN
40-966-068-F
-
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 68-Pin SCSI Style Micro D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
96-Pin Micro-D Connector Block, Male DIN Rail Mounted
40-966-096-M
-
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
200-Pin LFH PCI Connector Block, Male
50-965-200-M
-
Suitable for use on the front of PCI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross sectional area and insulation properties.
-
Product
Die-cast Rotor Tester
AIP868X series
-
Qingdao AIP Intelligent Instruments Co., Ltd
Introducing the international testing technology and developing special sensor according to digital signal processing method, the die-cast rotor tester able to automatically analyze and judge the filling quality of die-cast rotor.This system is applied to all kinds of cast aluminum and copper rotors, such as: cast aluminum rotor of compressor motor, cast aluminum rotor of washing machine motor, cast aluminum rotor of fan motor, cast aluminum rotor of pump motor, rotor of automobile motor and three-phase asynchronous motor, etc. The main detection functions are: broken bar, fullness of the bar (thin bar, hole, bubble and porosity ), leakage between the squirrel cage and lamination, squirrel cage eccentricity, slot deviation.Test items: broken bar, thin bar, maximum amplitude value, minimum amplitude value, comprehensive value.
