Voltage Converters
Changes the voltage of a source.
-
Product
Ethernet To Fiber Optic Converters (Multi-Drop)
-
Our advanced, rugged, industrial-grade, Fast and Gigabit Ethernet to multi-drop fiber optic converters are designed to cover large areas. These converters support up to 255 fiber nodes, and each fiber node can extend the Fast and Gigabit Ethernet data up to 100 miles or 160 km. Depending on the site situation, these multi-drop fiber optic converters can be configured as a daisy-chain or a self-healing redundant ring fiber network. When configured as a ring fiber network, the built-in self-healing feature allows the Ethernet data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same fiber ring, making the entire Ethernet network more robust and reliable. These Fast and Gigabit Ethernet to multi-drop fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
Product
DC/DC Converter 2 W
R2SX-2405/H-R
-
DC/DC converter with 2 W from Recom | input ranges 21.6 - 26.4 VDC | output 5 V | operates in ambient temperature from -40 to +100 °C | high isolation version | tape and reel packaging
-
Product
Voltage Variable Attenuators
-
Voltage variable attenuators (VVAs) that offer up to 60 dB of attenuation across a broad range of frequencies from 400 MHz to 18 GHz. These voltage variable attenuators are frequently used in applications such as electronic warfare, instrumentation, point-to-point and point-to-multipoint radios, fiber optic and broadband telecom, microwave radio and VSAT, military radios, radar, ECM, SATCOM and sensors, and R&D.
-
Product
RF Voltage Probe
P-20 Series
-
The P-20A is a PASSIVE 10:1 RF VOLTAGE PROBE with a 50 Volt DC BLOCK built in. It has been designed to allow users of RF test equipment to use standard signal tracing techniques. The P-20A makes it possible to conveniently and accurately monitor or inject signals up to 3 GHz into RF circuits without significantly loading or detuning them.
-
Product
DC/DC Converter 3.5 W
REM3.5E-0524S/R10/A
-
DC/DC converter with 3.5 W from Recom | input ranges 4.5 - 9 VDC | output 24 V | operates in ambient temperature from -40 to +95 °C | 10 kVDC isolation
-
Product
10-Ch. 0… 5V 400mA Isolated
YAVAP955
Programmable Voltage Source
The YAV board AP955 contents 10 CAN Bus programmable bipolar Isolated precision and low noise 0 to 5VDC voltage sources up to 400mA output, with Tripaddle VPC connector.
-
Product
IMPULSE VOLTAGE GENERATOR
-
International Biological Laboratories
The impulse voltage generated in the electric power transmission and distribution system due to lightning or switching phenomena can be simulated by generation of impulse voltage of particular shape in the laboratory.
-
Product
Impulse Voltage Generator
-
Hilo-Test manufactures Surge generators for surge voltage and safety tests as well as for testing the insulation withstand voltage, the waveform in accordance with IEC 60060. Especially for EMC tests on photovoltaic systems and surge voltage tests, for example, to relay, capacitors, coils.
-
-
Product
High Voltage Amplifier
HA-405
-
* 400Vp-p(±200V DC)* 400mAp-p(±200mA DC)* Bandwidth: ≦1MHz(200Vp-p) *Slew Rate: 500V/us *Gain(AMPL):0~90(10 Turn VR) *DC Offset: ≦0~±200V(10 Turn VR+SW) *Output Resistor: 50Ω *Microprocess Control Protection
-
Product
- RS-232 to RS-422 Interface Converter
Model 263
-
No AC or DC Power; Full Duplex RJ-11 and Screws; Surge Protection. The Model 263 power stealing RS-232 to RS-422 interface converter offers the user the benefits of other Telebyte converters without the problem of supplying power. With only TD, RD and Ground the Model 263 will provide operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
Product
DC/DC Converter 2 W
REM2-1512D
-
DC/DC converter 2 W from Recom | input ranges 13.5 - 16.5 VDC | outputs +/-12 V | operates in ambient temperature from -40 to +95 °C
-
Product
Current, Voltage, Resistance
-
Solutions for the testing and calibration of current, voltage and resistance are used in industry (laboratories, production, workshops), in calibration service companies and in quality assurance. These instruments are portable and mobile and are particularly notable for their low measurement uncertainty and high scope of operation.
-
-
-
Product
Non-Contact Voltage Tester
NCVT-1
-
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
Product
Uniload Voltage Transformer
2J4-4
-
The Type 2J4-4 Knopp Uniload Voltage Transformer Test Set consists of three major parts:
-
Product
Voltage Integrated Sources
VIS
-
The VIS voltage integrated source was designed to be used as a stable alternating voltage source for electricity meter test equipment, and in laboratories. The output voltage is isolated and independent of mains voltage. VIS is available in a variety of configurations depending on the values of output power and output voltage.
-
Product
DC to Synchro and DC to Resolver Converters
-
Computer Conversions Corporation
The LDS 500M Series are high accuracy, drift free, and continuously updating DC-Angle to Synchro or Resolver Converters designed for Military and Industrial simulation and control applications.
-
Product
Voltage Indicators
-
*Measures voltage from 100V to 138kV line‑to‑line.*Can be used individually as voltage indicators or together for phasing operations up to 100 ft (30 m) apart.*Two LED displays are automatically synchronized during phasing operations.*Clear in-phase and out-of-phase indication.*Versatile for overhead and underground applications.*Capacitive Test Point and Peak Hold modes
-
Product
Voltage & Continuity Testers
-
Our range of CombiVolt voltage testers are designed to measure AC/DC voltages and continuity. Most models provide LED indication, an audible tone or a combination of both while others have a digital display to give an exact reading, all testers have a non RCD Trip feature
-
Product
Voltage Meter
МН32СМ
-
The mezzanine module (mezzanine) МН32СМ is designed to measure instantaneous voltage values over thirty two two-wire differential channels.
-
Product
Electrical Tester For Voltage
PDT35
-
Automatically Selects VAC, VDC, or Continuity TestComplies with EN 61010-1 For Use in CATIII 600 V Environments1999 Count LCD DisplayAuto Power On/OffHigh Input Impedance -- 400 kVoltage AC: Max Range 600 V, Accuracy +/- 1.5%Voltage DC: Max Range 600 V, Accuracy +/- 3.0%Continuity TestAccessories Included: Test Leads, 2 'AA' BatteriesDimensions: 8.46' H x 2.83' W x 1.44' DWeight: 8.29 oz.Sold as : Unit
-
Product
Current/Voltage/Frequency Converter
SCMA-VADC-710
-
The SCMA-VADC-710 current/voltage/frequency converter is switched between SensoControl measuring devices and hydraulic installations in order to capture the switching status of these components
-
Product
DC/DC Converter 2 W
REM2-1505D
-
DC/DC converter 2 W from Recom | input ranges 13.5 - 16.5 VDC | outputs +/-5 V | operates in ambient temperature from -40 to +95 °C
-
Product
Photometric Converter
C4000
-
The C4000 converter is a multi channel controller capable of operating all optek photometric sensors. The C4000 converter allows for easy programming and operation, and can supply up to four real time configurable 4-20 mA output values correlated to any units of measure. The C4000 offers configurable relay alarms, can record and download process data, and can operate up to four sensors simultaneously.
-
Product
Compliance Voltage Ohmmeter
ΩhmRanger-LCV
-
ΩhmRanger-LCV is an accurate, 3.5 Digit, Low Compliance Voltage Ohmmeter. It is able to measure from >100M to 10 Ohms, ΩhmRanger-LCV is suitable for professionals and enthusiasts alike.
-
Product
Charge Converter
CH-6130/6140
-
The CH-6130/6140 charge converter is a simplified type of charge amplifier converting charge signal to voltage.It can be connected directly to an input BNC connector of a CCLD applicable equipment such as FFT analyzer or vibration comparator, enabling direct connection of a charge output pickup without suing a box type amplifier.
-
-
Product
CAN + OBD Network Data Converter
NC1
-
Get RPM, Speed, Absolute throttle position and many other vehicle parameters in real-time from your vehicle's standard OBD connector. Works with ANY OBD2 equipped vehicle. Works with ANY data acquisition equipment.
