Voltage Converters
Changes the voltage of a source.
-
Product
Data Converters
-
Omega carries an extensive line of data converters, including RS-232 to USB interface converters, fully isolated RS-232 to RS-485 converters, industrial ethernet to serial device servers, and more.
-
Product
High Voltage Insulating Tester
-
Suitable for preventive maintenance of gapless arresters.By simply clamping around the ground wire of an arrestor with a clamp CT, it detects leak current and leak current resistance components.
-
Product
RS232 to DMX Converter
DS232
-
RS232 to DMX Converter Controller Driver. Connect an RS232 terminal or computer port and drive DMX controlled dimmers and devices. A set of commands and auto fade rates offer power and flexibility for controlling DMX equipment. Use any RS232 terminal application to create command strings to: turn on, off, fade up, and fade down dimmer 256 DMX channels.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-244-HI
Programmable Resistor Module
The 40-230-244-HI (PXI) and 42-230-244-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 1.5MΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
-
Product
Lock-In Voltage Preamplifier
SR552
-
Stanford Research Systems, Inc.
The SR552 Voltage Preamplifier is designed to work with SRS lock-in amplifiers, providing gain where it is needed most?right at the experiment. The preamplifier minimizes noise and pickup in the connecting lines and can reduce measurement time in noise-limited experiments.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-221-HI
Programmable Resistor Module
The 40-230-221-HI (PXI) and 42-230-221-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 925Ω with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Easy Connection Of IEPE Sensors To Voltage Input Measurement Devices
K- IEPE
-
Our K-IEPE module is designed to connect IEPE sensors to a voltage measurement device that normally cannot support IEPE sensors. The powered K-IEPE module simply enables IEPE sensors to be connected via the BNC terminals and will output the signal voltages to an analog measurement device.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-131-HI
Programmable Resistor Module
The 40-230-131-HI (PXI) and 42-230-131-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 13.6kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-032-HI
Programmable Resistor Module
The 40-230-032-HI (PXI) and 42-230-032-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 26.7kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High Voltage Optically Isolated Probe, 700 MHz Bandwidth. Includes soft-carrying case.
DL07-ISO
-
The DL-ISO enables highest confidence in GaN and SiC device characterization with highest accuracy, best signal fidelity, and comprehensive connectivity.
-
Product
High Voltage Divider
-
The High voltage divider type HVT ... RC possess from DC up to their cut-off frequencies in the MHz range uniformly excellent transmission characteristics. The voltage divider consists of a resistive branch, which is constructed of high-grade resistance, and a capacitive branch with series damping.
-
Product
LXI High Voltage Matrix
65-218-121-CC
-
The 65-218-121-CC is a plug-in module is part of a scalable high voltage matrix platform designed to provide a large matrix solution with a switching capacity of 1000V without access to the chassis backplane.
-
Product
HIPOTS (High Voltage Testers) / AC Hand Gloove and Boot Safety Tester
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Compact and rugged BDV testers for AC dielectric withstand / breakdown testing of Safety glooves and boots. Panel mounted controls and indicators with easy to follow legend.
-
Product
Low Voltage Testers
-
Device used to identify opens and shorts in applications that are driven on low voltages.
-
Product
NI-9262, 1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module
785503-02
Voltage Output Module
1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module - The NI-9262 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. The NI-9262 module includes a channel-to-earth ground isolation barrier for safety and noise immunity.
-
Product
High Voltage Diode Assemblies
-
High voltage diode assemblies are built by adding diodes in series to yield a higher peak inverse voltage. For example, if each diode is rated for 1200 peak inverse voltage (PIV), then six diodes in series would have a total peak inverse voltage of 7200 PIV. The detailed circuit is shown below.
-
Product
FaithTech Ultra Low Voltage And High Current DC Load
NZ/N Series
-
Shenzhen FaithTech Technology Co., Ltd.
Ultra low voltage and high current DC electronic load is a high reliability and high performance electronic load product derived from FT conventional electronic load for low voltage and high current test scenarios such as fuel cell test and CPU power supply device test. For different current levels, this product includes two series: NZ and N. The voltage is 0-20V or 40V, in which the NZ series can be loaded with 0V full current, and the N series can be loaded with ultra-low voltage and full current. The load capacity is up to 0V@1200A and 0.2V@5000A . This series of products has high precision and high cost performance, which is your good choice for testing.
-
Product
High Voltage 50 Pin D-Type Cables - Connector to Connector for Pickering
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a high voltage 50-pin D-type connector.
-
Product
High Voltage Isolation Test Systems
HT 9460 and 9464
-
Accurate and non-destructive production testing of ac Isolation Voltage and Partial Discharge. With over 450 systems installed worldwide the 946X series of test systems are the standard and system of choice used by the majority of semiconductor manufacturers that produce optically isolated devices.
-
Product
51-Pin REDEL High Voltage Cable Assembly, Male To Unterminated, Ferrules, 0.25A, 2m
A051KMR-F-HA200
Cable Assembly
This is a 2m long male to unterminated 51-Pin REDEL high voltage cable assembly with ferrules constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips areprovided to secure the connector to associated product.
-
Product
80-250V AC/DC Voltage Tester
1931
-
Peaceful Thriving Enterprise Co Ltd
*Handy pocket clip.*With cETL Approval.*Bright neon indicator.*Insulated housing and test leads.*Check voltage on 80-250V AC/DC.
-
Product
Automatic Voltage Transformer Comparator
KATC-V2
-
Knopp’s KATC-V2 is a highly accurate state-of-the-art voltage transformer comparator that is compatible with all older generation Knopp comparators, and is designed to be a direct, plug-in replacement with additional test set cables to fit in the existing Knopp Voltage Transformer Test Systems.
-
Product
Fuel Flow and Torque Converter
Model 44SM1
-
This self-contained, remotely mountable Second Harmonic Fuel Flow Interface accepts data from a second harmonic fuel flow transmitter then converts this information into a frequency output proportional to fuel flow. In addition, this module will accept signals from a T56 Torque Tranducer and provide a DC voltage proportional to Torque. Typical application is for use with Flight Management and Nav Management Systems. The use of field proven designs and carefully selected components assures high reliability field performance.
-
-
Product
Low Level Voltage Measuring Instruments
-
This instrument has a very wide range of source resistance capability and has an equivalent noise resistance of less than 10 ohms. Sub-nanovolt resolution is possible. The N11 has many applications, including cryogenic measurements.
-
Product
High Voltage Phasing Sticks
9007KB Series
-
Shanghai Beha Electronics Co., Ltd.
*Important applications include checking voltage fuses, testing for correct phase connections, and for absence of high voltage on deenergized lines or apparatus.*measuring ranges from 6.6kV up to 44kV systems*Fiberglass is of hot stick quality and tested to IEC specs (100kV/300mm for 1 min). All front end (resistors) are encapsulated.
-
Product
Converter Signal Amplifier – 4…20 mA – DIN Rail
HD978TR3
-
Configurable converter signal amplifier with 4…20 mA (20…4mA). Input range -10 …+60mVdc.
-
Product
50 Ω High Voltage Pulse Generators
-
High Power Pulse Instruments GmbH
50 Ω High Voltage Pulse Generators by HPPI GmbH
-
Product
DC/DC Converter 12 W
RP12-11012DAR/P
-
DC/DC converter 12 W from Recom | input range 36 - 160 VDC | outputs +/-12 V | operates in ambient temperature from -40 to +85 °C
