Component
Testing of individual hardware or software components or groups of related components.
-
Product
Terminal Test Kit (19 PCS)
3605
-
Peaceful Thriving Enterprise Co Ltd
1. Check high and low voltages (power and ground) on 6, 12 and 24V system.2. 4mm connection for banana plugs.3. LED indicates red for power (high) and green for ground (low).4. High impedance protects sensitive electronic ignition components.5. Connects red lead to power source and black lead to ground source.6. 1.8m long heavy-duty dual leads with battery clips and spring strain relief.7. Facilities the measurement on connectors and components without destroying the insulation or the plug connection.
-
Product
Capacitance Tester
LCR55A
-
The ultimate electronic component verifier measures inductance, capacitance, resistance, transistors, diodes and microwave diodes.
-
Product
Automated Surface Inspection for Glossy Components
-
Flawlessly glossy surfaces are among the most important quality features of many premium products. The smallest surface defects immediately have a degrading effect on the product. The result: disappointed end customers or buyers. At the same time, reflective surfaces are often very sensitive and a challenge for optical metrology. A manual inspection is tedious, expensive, and ultimately always governed by subjective decision criteria. During production, faulty painting or coating processes can cause high scrap rates. Defects that are not detected even during the final inspection can lead to expensive complaints and, in the worst case, to the loss of the customer. Only an efficient, automated surface inspection achieves the highest quality at acceptable costs.
-
Product
Alligator Test Clips
-
Alligator clips are spring loaded clips that are used to temporarily connect wires to components on circuit boards, connector pins, or other terminals.
-
Product
ATE Parts
-
Comware Technical Services, Inc.
We have thousands of parts in stock including hard to find legacy system components. For the best pricing, service and quality look to Comware for replacing your GenRad, Teradyne , Agilent and TRI system parts and modules.
-
Product
Single Channel Error Rate Tester
Basic Bert
-
Already as a single channel BERT the PARALLEX® system offers full functionality for testing high speed components. PRBS and user pattern generation and error detection for 2..13Gbit/s.
-
Product
Plugbord
3677-3
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers. 3-Hole solder pads (0.28” x 0.080”) and buses forinterconnecting multiple component leads.No pattern on reverse side, edge contacts only Row and column legends provided.
-
Product
Basic Pneumatic Trainer
-
Unitech Scales And Measurements Pvt. Ltd
It consists of a basic pneumatics kit components for, FRL unit solenoid valve, cylinder etc. This basic pneumatics kit shall be capable of being used to demonstrate to the design, construction and circuits.
-
Product
Preparative HPLC Systems
Nexera Prep
-
*Easy optimization of preparative parameters and scale up Fractionation simulation for rapid setup of collection logic Column line-up for scale-up from analytical to preparative*Time- and energy-saving by automation of the purification workflow Collection of target components at high purity by automated desalting*Expandable to suit the sample/fraction number and volume Choose from a wide range of options for recovery scale and analytical detection Problems are resolved simply, to accommodate a variety of needs.
-
Product
Modular Infinity Microscope
MIM
-
Applied Scientific Instrumentation
ASI Modular Microscope components consist of tube lenses along with adapters and accessories that either are primarily used in the collimated light space or adapters that are to be used on the image side. Collimated light adapters use the 38mm diameter C60-RING system to connect components. Focus-side adapters attached to lens tubes with either a 30mm diameter coupling to the I.D. of the C60-TUBE, or with a 50mm coupling on the O.D. of the lens tube.
-
Product
Walk InDrive In Chamber
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Walk in/Drive in chambers can make test for large components, finished products like automobile.According to different test requirement and application, walk in chamber could divide into 2 types: Welded walk-in chamber and Modular walk-in chamber.
-
Product
Temperature Chamber
S/SM-Series
-
Thermotron's S/SM-Series temperature-only and temperature-humidity environmental test chambers deliver quality, accuracy, and reliability. The self-contained refrigeration system and diverse compressor size options provide moderate temperature change rates while allowing the climatic chamber to consume less power than comparable test chambers. From prototyping and durability testing to component screening, the S/SM-Series is a cost-effective testing solution.
-
Product
Rubidium Oscillator
IQRB-2
-
The IQRB-2 low noise rubidium oscillator is a sub-miniature atomic oscillator combined with 'active noise filter' technology. This rubidium oscillator has 100 times less drift than OCXOs and with short term stability of 0.002ppb/s at 100s this rubidium oscillator provides significant improvements in performance over other rubidium components.
-
Product
AC source/sink
-
The static AC source contains tried and tested components from our UPS technology., Available with adjustable output frequency and/or output voltage., Clear design, tried and tested components and easy maintenance characterize this AC source.
-
Product
Antenna Switch
SixPak
-
The SixPak has two components: a relay matrix and a control box, there are several options for the controller.The relay matrix allows the selection of any 6 antennas by 2 radios or feedlines. Its lockout circuitry prevents both radios from selecting the same antenna. (The 6x1 type of SixPak is now replaced by our RatPak remote 6 way antenna switch.)The usual set-up has one SixPak dual rotary control box, which is manually operated from the radios positions. The control box for the 6x2 contains two rotary switches and 12 LEDs, so the operator can see which antennas are selected.
-
Product
Tribocorrosion Tester
ASTM G119
-
Tribocorrosion involves studying Wear Evaluation of Protective Coatings. It involves mechanical and electrochemical interactions between components in motion. Rtec Tribocorrosion modules measures inline current, voltage, friction, wear, temperature , down force, ear, acoustic emissions at all times. Currently used by several Fortune 500 firms globally.
-
Product
Electrostatic Discharge Test
-
The electrostatic discharge test is designed to determine the ability of equipment to perform its intended function without permanent degradation of performance as a result of an air discharged electrostatic pulse. Electrostatic discharge is the result of an unbalanced electrical charge. Typically, it is created by insulator surfaces rubbing together or pulling apart. A transfer of electrostatic charge between bodies (materials, components, etc.) at different electrostatic potentials is caused by direct contact.
-
Product
DC Power Supplies
-
Scientech Technologies Pvt. Ltd.
Power Supply is the most indispensable component of any electronic laboratory. A reliable, most accurate, fully specified, guaranteed and an efficient Power Supply Equipment are thus manufactured on a large scale by Scientech Technologies which has robust output protection and fault detection capabilities. DC Power Supplies with Different specifications of Voltage and Current are being manufactured for various Applications. The DC power supply converts the conventional 110 V or 220 V alternating voltage into continuous pulsating DC voltage (+3.3 V, +5 V, +12 V and -12V) used by various electronic components. A DC Power Supply also regulates the voltage to eliminate spikes and surges common in most electrical systems.
-
Product
LCR Meter
Hantek1832C/Hantek1833C
-
Qingdao Hantek Electronic Co., Ltd.
Hantek1832C/Hantek1833C handheld LCR Meter is a portable handheld measuring instrument to measure the parameters of the component such as inductance, capacitance, resistance and so on.small volume, powered by 5V lithium battery, it can meet the requirements of desktop LCR application, and can also be applied to flow measurement and handheld measurement.
-
Product
Thermal Controlled Chucks & Plates
TOP Cool
-
Mechanical Devices newest innovation in thermal testing. Each TP system contains a thermal chuck or thermal plate and a self-contained thermal control unit.The TP chuck and platforms is a breakthrough product that introduced the use of refrigerant for active cooling & heating of wafers and other components with no need of chiller, CDA, or consumable and expensive refrigerants such as liquid nitrogen and liquid carbon dioxide. It can be a perfect replacement system in the industry for uncompromising thermal and mechanical performance with a temperature ranging from -60 to +220°C.
-
Product
Fully Automatic Eddy Current Crack Test System
ROTO-PUSH
-
Foerster Instruments, Incorporated
The ROTO-PUSH test station, which is integrated in production lines, serves to test cylindrical components for cracks in the liner surface. The testing configuration has to be rotated for automatic crack testing. After the test, the test pieces are sorted and separated. The continuous test run ensures a high testing rate, which increases profitability.
-
Product
CAM/GATE Test Kits
Series 45
-
The CG Series 45 CAM/GATE linear over clamp kits utilize the same patented “Z” axis motion as our CAM/TRAC® Series products offering precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The latch assembly engages and disengages when actuating the clamping assembly. The CAM/GATE utilizes a cam roller system for precision guiding and smooth operation and 1.00” push plate movement. The gate assembly is movable to three different positions which allows for the versatility of top side probing, or relocating the frame assembly for PCA’s the have tall components
-
Product
Light Shaping
-
VirtualLab Fusion supports light shaping by freeform surfaces, diffractive beam splitters and pattern generators, diffusers, and general arrays of micro-optical components, including, but not limited to, micro-lens arrays.
-
Product
Photo Optic Sensors
-
From patient monitoring in hospitals, to wearables and home healthcare applications, TE Connectivity (TE) offers photo optic sensors and components for non-invasively measuring blood oxygenation (SpO₂) level. With more than 27 years of proven reliability and expertise, TE has designed SpO2 sensors with best-in-class flexibility to accommodate multiple wavelength options. Our ability to provide both components and complete sensor packages make us the leading choice for pulse oximetry applications that require high degrees of precision, durability and performance.
-
Product
PXI
-
LinkedHope Intelligent Technologies Co.,Ltd.
PXI systems are composed of three basic components — chassis, system controller, and peripheral modules.
-
Product
Data Loggers
-
Identify trends in vibration, noise, temperature, humidity and more that can be indicative of component wear and/or influence machine performance with help from PCE Instruments' data loggers.
-
Product
Measuring Stations
-
The main application is the measurement of the flux density on the surface of multipole magnets or components with magnets. A large amount of measuring stations is built for rotors.
-
Product
Level Sensors
-
*High reliability due to the elimination of mechanical components*Different function principles: Guided wave radar, capacitive and hydrostatic*Devices for limit level detection or continuous level measurement*Clearly visible LED display*Suitable for all common industrial and process fluids
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800B (2RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800B (2RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
Breakout Box
FV-EXT
-
The handy FiberVision devices FV-EXT1 and FV-EXT2 are designed for the easy integration of FiberVision and Vision Component (VC) smart cameras into your production environment.Central interface for all supply- and communication-cables (switch board)Remote control for all VC based smart cameras such as Caminax or PictorTest of digital camera I/Os and the production environment
