Kelvin
-
Product
Banana-Triax Adapter For 2‑Wire (Non-Kelvin) Connection
N1297A
Accessory Kit
The N1297 Series is a collection of banana-triax adapters for the Keysight B2900 Series precision source measure unit (SMU). It consists of both 2-wire as well as 4-wire connection requirements.
-
Product
Medium Kelvin Clip Lead
16089B
Accessory Kit
Measure odd-shaped components that you cannot measure using conventional fixtures
-
Product
Single-Point Kelvin Probe
-
Our Single-Point Kelvin Probe system (KP020) is the introductory system in the KP Technology product family. The off-null signal detection method allows high-quality measurements of the Work Function/Fermi Level of materials.
-
Product
Turret Contactors
-
Design available for all Turret handler models. Leaded and Leadless packages, device pitch down to 0.20mm for Kelvin and Non Kelvin testing on both thermal and ambient environment.
-
Product
Micro-Ohmmeters
-
The Micro-ohmmeter performs reliable low resistance measurements with test currents to 10A and resolution to 1. Uses a four-wire Kelvin bridge method, which eliminates test lead resistance for a measurement accuracy of 0.25%.
-
Product
CableEye 4-Wire Calibration Verification Board | Cable & Harness Testers
CB52
-
The CB52 is intended for periodic calibration verification of the Kelvin 4-wire resistance measurement module – an optional, add-on module that may be purchased with any new hipot system, or added to an existing high voltage tester as an upgrade.
-
Product
Connector Test
-
A connector test system which provides expansion of up to 160 Kelvin pair connections. The system incorporates high voltage AC and DC power supplies with a maximum output of +/- 2100 Volts peak for Hi Pot, Insulation resistance measurement. LCR bridge control is provided with 4 terminal multiplexing in order to add precision capacitance, inductance and resistance measurement capability. An integral H.V. capacitor bias option permits capacitance measurement to be made at up to 2.1kV.
-
Product
Ultra-High Vacuum Kelvin Probe
-
Our Ultra-high Vacuum Kelvin Probes give the user full access to work function and contact potential difference (CPD) measurements under vacuum. Each system comes with a high-quality, manual, or motorized translator that enables reliable and accurate tip-to-sample positioning, and the unrivalled tracking system always holds the tip separation constant during the measurement. Even under vacuum, the work function resolution is 1 - 3 meV.
-
Product
Ultra-High Vacuum Scanning Kelvin Probe
-
Our Ultra-high Vacuum Scanning Kelvin Probes (UHVSKP2020 and UHVSKP5050) give the user full access to work function (Φ) and contact potential difference (CPD) measurements under vacuum with the ability to scan a sample area of 20 x 20mm or 50 x 50mm respectively. Each system comes with the UHV head unit, tip amplifier (located at the mounting port), digital control unit and host PC with dedicated software. The tip can be retracted 100mm from the sample and approaches normal to the sample. The associated digital electronic unit powers the head unit and provides an interface between the head unit and the data acquisition system. The system comes with a complete user manual, which includes an introduction to work function measurements and a detailed description of the system software, including examples. The work function resolution of the Ultra-High Vacuum Scanning Kelvin Probes is 1-3 meV.
-
Product
Short Circuit Locator for Power Cables
A910
-
The A910 is a short circuit locator designed for fault location in power cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A910 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total resistance greater than 5mohm (approximately 90 m of 300 sqmm cable) and less than 30 kohms. The distance to fault is measured as a percentage of the total length of cable and is displayed on a large LCD display.
-
Product
Cable Length Meters
CLM-1000E
-
*Measures these metric wiresizes: 0.75, 1, 1.5, 2.5, 4, 6, 10, 16, 25, 35, 50, 70, 95,120, 150, 185, 240, 300, 400,500 mm2*Eight user-programmable settings for other sizes*Powered by (6) 1.5V AA batteries*Replacement calibration rods (pair) available as CLM-ROD, UPC 02721*Replacement Kelvin clips (pair) available as CLM-CLIPS, UPC 02722*Meters
-
Product
Kelvin Probe Set
11059A
Accessory Kit
Reduce ground-related errors and contact resistance through gold-plated flat tweezers and special gripping surfaces
-
Product
Precision Micro Ohmmeter
BS407
-
High basic accuracy of 0.1%Wide range of 1 µΩ to 20 kΩCurrent reversal switch for detecting thermal EMF effectsCurrent diversion switch for easy zeroingFour terminal measurement using Kelvin clip leads (supplied)Battery operation with built-in charger20mV clamp for "dry circuit" testing
-
Product
Cable Length Meters
CLM-1000
-
*Measures these AWG wire gages: 18, 16, 14, 12, 10, 8, 6,4, 2 , 1/0, 2/0, 3/0, 4/0*Measures these kcmil wire sizes: 250, 350, 400, 500, 600, 750, 1000*Eight user-programmable settings for other gages*Powered by (6) 1.5V AA batteries*Replacement calibration rods (pair) available as CLM-ROD, UPC 02721*Replacement Kelvin clips (pair) available as CLM-CLIPS, UPC 02722*Feet
-
Product
Ultra-High Vacuum Ф4 Scanning Kelvin Probe
-
The Ф4 Ultra-high Vacuum Scanning Kelvin Probe system gives the user full access to work function measurements under vacuum with the ability to alter the temperature from 77 K to 860 K. The Kelvin Probe measurement has resolution of 1 - 3 meV for a 2 mm tip on a conducting sample. The sample is mounted on a plate that is located on a motorized (x, y, z) translator attached to a stainless-steel vacuum chamber. Phi 4 also comes with a photoemission spectroscopy system with a tuneable source (3.4 - 7.0 eV). The deep ultra-violet (DUV) light spot measures approximately 3 x 4 mm. Absolute work function measurements can be obtained with this system in the range of 4.0 - 6.5 eV with an accuracy of 0.05 - 0.1 eV.
-
Product
Scanning Kelvin Probe Microscope
VS-SKP
-
The Kelvin Probe experiment uses a nondestructive method to determine the relative work function difference between the probe and the sample. Work function describes the energy required to liberate an electron from the surface of a conductor; electrochemists often interpret this as the difference from an electrode’s Fermi Level, average energy of electrons, and that of vacuum.
-
Product
Contact Probes
-
Rika Denshi Group Contact Probes - specialty probes including fine pitch testing, high frequency testing, high temperature testing, kelvin test, and high current test, as well as standard probes for 0.4mm-, 0.5mm-, 0.65mm-, 0.8mm-, and 1.0mm pitch.
-
Product
Kelvin Test Leads
-
Kelvin Test Probes, Kelvin Test Leads, based on the Parrot™ Clip Invention provide reliable contacts and connections for the Sense and for the Current leads .
-
Product
Temperature Meters
-
PCE Instruments’ temperature meter products are precise, portable, handheld devices ideal for professional, industrial, commercial and residential use. From contact temperature meter devices with probes to noncontact temperature meter devices using infrared or laser technology to measure temperature from a distance, PCE Instruments offers a wide range of accurate, reliable temperature meter products at an affordable price.Temperature is measured and recorded in many different applications. For example, HVAC technicians measure temperature to identify and address issues in heating or cooling systems, while quality control professionals in the food sector measure temperature to ensure the proper storage and preparation of everything from meat and produce to cheese and frozen foods. PCE Instruments carries a variety of temperature meter products, including temperature meter devices to measure different temperature ranges between -200 and 1767ºC / -328 ... 3212ºF; temperature meter devices that can indicate temperature in °C (Celsius), °K (Kelvin) and °F (Fahrenheit); and temperature meter devices that are water resistant. In addition, a number of thermal elements and type-K sensors are available for different temperature meter products.Each temperature meter comes factory calibrated to ensure accurate measurement. ISO-certified calibration, performed by one of our first-class calibration laboratory partners, may be obtained on most temperature meter models for an additional fee.A temperature meter is an instrument used to measure the temperature of beings or things. The most widely recognized temperature meter is a mercury thermometer used to measure the temperature of people. These thermometers consist of a graduated glass capillary with a pool of mercury in one end. However, there are many different types of temperature meters, such as digital thermometers that take temperature measurements on contact with an object or infrared temperature meters that take measurements at distance, without contact.
-
Product
Test Fixture, Axial And Radial
16047A
Test Fixture
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
Product
High Power Precision Current Sensing Resistors
HPCR4T
-
High Power Precision Current Sensing Resistors of HPCR4T designed with four terminals, are distinguished by excellent long term stability & TCR. The Kelvin connections of this device allow for high precision measurements even with low resistance values. HPCR 4T has a non-inductive copper manganin element inserted into the ceramic case and finally sealed with a cement molding.
-
Product
Cryogenics Testing Lab
-
DPACI Cryogenics Test Laboratory has been operational for over a decade providing test data, temperature cycling, simulation, and analysis for our customer’s rigid deep space component qualification requirements. Our firm provides our customers with most accurate test data taken at temperatures ranging from 10°Kelvin to 400°Kelvin.
