Monitoring
-
Product
Total Hydrocarbon THC/VOC Monitoring System
ML661
-
The Teledyne ML®661 is a complete engineered CEMS designed to measure total hydrocarbons (THC/VOC) as required in environmental regulatory compliance and process control applications. Please consult our factory for more information on this product.
-
Product
Portable heat flux sensor, with read-out unit
HF03 / LI19
-
Hukseflux Thermal Sensors B.V.
The HF03 is a heat flux sensor that can be used in mobile applications. It is combined with LI19, a high accuracy hand-held read-out unit that can be used both for mobile measurements and as an amplifier directly connected to a PC. The combination HF03 / LI19 is typically used to study heat flux levels around flares and fires, and to calibrate flare radiation monitors / flare heat flux sensors.
-
Product
CO, Alcohol and VOC Gas Sensor Breakout
MiCS5524
-
Give your next sensor project a nose for gasses with the Adafruit MiCS-5524 Gas Sensor Breakout. This breakout makes it easy to use this nice sensor from SGX Sensortech. The MiCS-5524 is a robust MEMS sensor for indoor carbon monoxide and natural gas leakage detection, it''s suitable also for indoor air quality monitoring; breath checker and early fire detection.
-
Product
SolarWinds SQL Sentry
-
Monitor, Diagnose, and Optimize With SolarWinds SQL Sentry Start a free, 14 day trial of SolarWinds SQL Sentry.
-
Product
Gas Analyzers
-
Omega's Handheld Gas Analyzers are ideal for monitoring VOC levels in petrochemical plants, power plants, mining facilities and restaurants. Models available to measure CH4, CO, O2, and H2S
-
Product
MIL-STD-1553 A / B Test And Simulation XMC Module
XMC-1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Hall-Sensor Board with analog output
041-970
-
The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Battery Capacity Tester
BLU-T Series
-
Battery load bank BLU-T is a powerful and lightweight solution designed for condition assessment of telecommunication and radio equipment backup supply. This instrument can perform the battery capacity test on battery strings such as Pb, Li-ion, Ni-Cd, and others. It tests battery strings with voltages in the range of 0,9 – 70,5 V DC. As a special feature, the BLU110T model enables capacity testing of single PB, Ni-based as well as Li cells (with current up to 100 A).The capacity test is conducted in an accurate, user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU-T battery load bank enables setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, the BLU-T units can be connected in parallel, or BXL-T additional load units can be linked.The instrument offers a high power-to-weight ratio. BLU-T series has models starting from 12,8 kg / 28.2 lbs and up to 19,2 kW of power.A user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Discharge parameters can be monitored in real-time during the capacity test. A 4,3-inch touch screen shows overall battery voltage, discharge current, discharge test time and capacity during the entire test. Also, the capacity tester is compatible with DV-B Win software. A user can view a detailed numerical and graphical presentation of key parameters, and create reports in various formats.Testing can be carried out without disconnecting the battery from the service.
-
Product
PCIe Color Industrial Camera
CMOSIS CMV4000
-
2K camera Applications: In-situ optical inspection camera, fast process capturing, e.g. Golf club swings, Intelligent Transportation Systems (ITS), Open road tolling and Traffic monitoring, Industrial Automation, Machine Vision, Facial Recognition, Motion Capture, Automotive crash testing, OCR/ OCV, 3D scanning, Robotic Arms, Material and Life science Microscopy, Ophthalmology and Retinal imaging, Medical Imaging, Flat panel inspection, Dental, Kiosks, Security, Biometrics
-
Product
ISDN-Testers
-
Is an ISDN Tester for use in the installation and maintenance of BRI S/T/U and POTS accesses – including BRI S/T NT and monitor modes.
-
Product
Gyro Pressure
-
Used to monitor the vacuum developed in the system that actuates the air driven gyroscopic flight instruments.
-
Product
TD Guard
-
TD Guard Intelligent Sensor is an on-line CONTINUOUS Capacitance and tan-δ monitoring system for transformer bushings. TD Guard Intelligent Sensor is the first and only instrument on the market providing absolute Tan-δ measurement in on-line permanent monitoring of transformer bushings, granting the best level of diagnostic leverage and reliability. Sensitivity better than 10-4.
-
Product
4 Station Endurance Test Setup for Thermostat of Iron
-
SCR ELEKTRONIKS have developed 4 STATIONS ENDURANCE TEST SETUP FOR THERMOSTAT OF IRONwhich is used for carrying out endurance test for thermostat of iron for the required amount of time It is very useful and handy in line testing on Mass production line as well as type Testing. It consists of Voltmeter, Wattmeter, Programmable Logic Controller( PLC ). The equipment continuously monitors faults like Contact weld and Contact Open. The other important feature is we can operate the panel in Auto Mode or Manual mode. User friendly operations make the equipment to be handled easier for any operator. This manual contains information about operating instructions and maintenance of the equipment.
-
Product
IDevice Calibrated Measurement Microphone
IMM-6
-
The Dayton Audio IMM-6 is a professional-quality measurement and recording microphone that is designed to work with the entire suite of Apple “iDevices” – iPad, iPhone, and iPod. The rugged construction and compact size make it the perfect companion for audio professionals who must work on-location performing acoustic analysis, monitoring audio levels, or recording. Each IMM-6 is individually hand-calibrated using a laboratory-standard measurement microphone, for consistent, repeatable measurements that match the level of precision previously offered only by expensive stand-alone microphones.
-
Product
Receiver Systems for Monitoring, Surveillance and Logging
-
We produce complete turn-key radio monitoring systems ranging from portable single-channel applications for field tests and drive-by coverage measurements, to large scale computerized multi-channel surveillance systems capable of monitoring thousands of channels simultaneously.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Multi Circuit Leakage Current Monitor
MCM-8000
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●The leakage current of max.8 circuits at the same time.●Easy for data management (storage by CSV formula)●Cost performance, high-speed sampling with high-frequency cut function.
-
Product
Zero Bias Schottky Detectors
-
KRYTAR Zero Bias Schottky Detectors are specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications.
-
Product
5L Oxygen Concentrator
OxyTec-5S
-
The Oxytech 5S is an advanced oxygen therapy solution that provides its users with a higher standard of care. -Emphasis on Safety, High/Low Flow, High/Low Pressure, Low Oxygen, Power Failure alarms. Advanced, optional Monitoring Capabilities. -Ease of maintenance, convenient access or filter cleaning: due to its unique design, awarded with a Certificate of Design Patent. -Optimum patient comfort, due to its easy to use design, features and operation. -Lightweight (only 15.9 kg), quiet (less than 45dB), reliable (94% AVG oxygen purity).-User friendly, capable of operating 24 hours continuously.-Easy-to-read electronic control panel – with LCD display including an audio and visual alarm system indicating low oxygen concentration, power off, pressure circulation fault and compressor fault.-Minimal power consumption.-Controlled oxygen output – from 0.1 to 5.0 LP
-
Product
E1/Datacom Transmission Analyzer
DTA-BERT
-
DTA-BERT E1/Datacom Transmission Analyzer can perform E1 transmission performance test (BERT) and status monitoring on data link (V.35, V.24/RS232, RS449, RS530, X.21). Model T can also perform G.703-64K bit error test, PCM31/30 test and Jitter test. Featuring comprehensive functions, easy operation and compact design, DTA-BERT provides total solutions for E1 line analysis and maintenance.
-
Product
Scalable Studio Monitor System
Amie Systems
-
The compact, self-powered Amie Precision Studio Monitor is engineered to excel in critical audio workflows requiring accurate mix translation to a variety of environments. Amie flawlessly reproduces source material at any volume level, and exhibits a remarkable power-to- size ratio as well as true phase linearity for ultra-precise spatial imaging.
-
Product
Torque Meter
TorqueMate® PTT-Series
-
The PTT torque meter makes ISO 9001 documentation faster and easier. As an advanced torque controlling, monitoring and documentation solution, the torque analyzer enables operators and engineers to ensure product quality, safety and reliability promptly in a variety of manufacturing environments. The portable torque meters are designed for measuring torque, torque calibration, joint testing, auditing or force and load measurement.
-
Product
USB Tester 2.0
TLS-0050
-
The USB Tester will make it a snap to monitor voltage levels and current usage without having to re-wire your breadboard. Just connect to your oscilloscope or DMM test leads, and you're good to go! The USB Tester has both banana clip sized drills and standard 0.1" headers. When you are not testing current you can add a jumper for normal operation. The USB D+/D- pins are also broken out so you can monitor those on an oscilloscope, or for USB sniffing.
-
Product
Particle Counters
-
Testing and monitoring airborne particles in critical environments is incredibly important. That’s why Kanomax has dedicated itself to developing the best particle counting and monitoring instruments on the market. Perfect for cleanroom monitoring, mining environments, and engineering sites, our particle counters provide flexibility, and most importantly accuracy.
-
Product
Low Speed Daq & Industrial Recorders
-
Advanced software packages can be used with Yokogawa recorders, data acquisition instruments, and other measuring equipment to build an integrated PC-based data acquisition system. Ethernet communication interfaces support fast and easy connection to LAN environments, enabling remote monitoring applications and centralized back up services. Standard software for the configuration of measurement devices and applications offer easy set-up and minimizes preparation time. Yokogawa offers the right tools to simplify your applications.
-
Product
Lightning Warning Sensors
-
Lightning warning sensors measure the local, atmospheric electric field at the earths’ surface and the fluctuations in field strength. By monitoring the field strength, the potential for cloud-to-ground (CG) lightning discharges can be detected, and advance warning can be made when conditions are becoming favorable for lightning.
-
Product
IP Surveillance
-
In response to the enterprises’ crucial demand for security monitoring, PLANET IP Surveillance features H.265, H.265+ High Efficiency Video Coding (HEVC), AI face detection and recognition, along with AI-powered Video Analytics such as intrusion detection, cross line detection, loitering detection and more. Moreover, with PLANET’s user-friendly website management, NVR, Apps and free DDNS services, customers are able to monitor all devices remotely and easily.
-
Product
Advanced Thermal Imaging Camera
FLIR E54
-
The FLIR E54 is your entry into the Exx-Series, offering the resolution and sensitivity you need for basic condition monitoring, electrical/mechanical inspection, and building inspection. The 320 × 240 pixel thermal detector accurately measures temperatures up to 650°C (1202°F) and produces crisp, vibrant imagery that can be enhanced with patented FLIR MSX® technology for added detail and perspective. The onboard FLIR Inspection Route runs pre-planned routes to help you stay organized when surveying large or multiple locations. FLIR Ignite provides automatic uploading of E54 images directly from the camera to the cloud for easy, secure storage and sharing.
-
Product
Bench Digital Multimeter, Calibrated, 1 kV, 10 A, 3.8 Digit
72-1015 CAL
-
The 72-1015 CAL from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
Product
Advanced Voice Quality Assurance System
AVQA
-
R&S®AVQA is a non-intrusive voice assurance system that provides many integrated monitoring functions for ATC communications systems. These functions include:Quality assurance reports to CAAType acceptance of new IP systemsLive information about disturbance to ACC adminVoice quality report on ANSP interconnection (e.g. NewPENS)Network quality reporting
