Gel Cell Battery
-
Product
Battery Crush Nail Penetration Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL battery crush nail penetration tester is used to simulate the use, transportation, storage and disposal of various types of batteries under certain temperature conditions, when the battery is crushed (such as compacted garbage) or nail penetration, and to judge the battery safety performance. The battery is qualified as no disintegration, no rupture, and no fire.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Intelligent Battery Charger-Analyzer for Large Battery Systems
SuperMasterCharger
-
The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions.Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
Servo Computer Battery Crush Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Servo Computer Battery Crush Tester simulates the situation in which various types of lithium batteries are squeezed during use. Artificially present different conditions that may occur when the battery is squeezed.
-
Product
CP-2XX-6 Battery Probes
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 69Full Travel (mm): 1.75Recommended Travel (mil): 59Recommended Travel (mm): 1.50Overall Length (mil): 236Overall Length (mm): 6.00Overall Length Remark: Overall length does not include tail.Recommended Drill Size: #53 or 1.51 mmRec. Mounting Hole Size (mil): 61Rec. Mounting Hole Size (mm): 1.55
-
Product
CTEK US 0.8 Battery Charger
56-865
-
US 0.8 is CTEK’s smallest 12 V charger. It offers state of the art technology and is perfect for charging smaller 12 V batteries that can be found in motorcycles, jet skis, ATVs and lawnmowers. It is also suitable for maintenance charging “normal- sized” batteries such as car batteries.The unique display allows the user to follow the entire charging process. The US 0.8 is a compact and fully automatic 6-step charger for 12 V batteries from 1.2–32 Ah and is suitable for maintenance charging up to 100 Ah. The US 0.8 is splash and dust proof, delivers 0.8 A and is designed to protect vehicle electronics. It is non-sparking, reverse polarity protected and shortcircuit proof. The US 0.8 is delivered with 5-year warranty.
-
Product
Automotive Battery Production Line Tester
-
The Production Line Tester (PLT) is typically installed at the end of battery production lines (finishing). An electrical load test after formation charging is essential to assure performance and quality. The energy discharged during this test must be minimized to eliminate the need for recharging after testing.
-
Product
Winmeter Battery Analysis Software
-
Explorer Technology Group (ETG)
The Winmeter Battery Analysis Software enables the user download and integrate data from the DMA-35n-BATT, DSG-30 or DLV-30 products and produce text and graphical battery analysis reports. With these reports, the user can quickly identify batteries that are likely to require preventative maintenance.
-
Product
Battery Load Bank
-
Foresight Electronics Co., Ltd.
Utility is used for battery systems range from 21-30V, if higher current is needed, two or more FST-24V units can be linked together. Discharge to Battery string voltage as 24V, Cell voltage as 1.2V/2V/6V/12V adjustable stop points and multiple alarm designs to control the discharge process intelligently 7inch LCD touch screen for easy operation and showing various parameters real time Support RS232 real time monitoring by PC or SD Card download data after discharge
-
Product
Bi-axial Dynacell Load Cells
2527 Series
-
During tests carried out on servohydraulic machines, elements of the system are subject to acceleration. As a result, in addition to the force applied to the specimen, the load cell also reads forces resulting from its own movement and the mass of the grips and fixtures attached to it. Dynacell is the world's first truly dynamic load cell, designed from the outset for measuring dynamic loads. Dynacell introduces the following advantages:*Reduces dynamic load errors which can be a significant percentage of reading *Increases productivity by allowing higher frequency operation while maintaining test validity *Improvements such as doubling the frequency are common
-
Product
Battery Monitoring System
S5
-
BTECH's benchmark product designed for a wide variety of applications (UPS/Telco/Switchgear), the S5 can collect data from any battery type including cells with the highest amp hour rating (4000+), and the S5 systems will record all battery parameters.
-
Product
Large Telemetry Compressive Load Cell
TC-3.0-LG
-
DLM’s Telemetry Compressive Load Cells can be used independently or in combination as part of weighing platforms.They range from 100t to 300t and manufactured using high grade stainless steel, making these load cells particularly suited to rugged environments and the hire industry. Bespoke size compressive load cells can be designed upon request. Some applications include: tank weighing, hydraulic lifting operations, vessel weighing and certification.
-
Product
PXI Mixed Configuration Relay Module - 10 Cells Populated
40-138-AA-BB-CC-DD (10 CELL)
Relay
The 40-138 2A Relay Module with 10 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
In-Line Light I-V Testing for Solar Cells
FCT-750
-
In-line, light I-V and Suns-Voc measurements in a single flash at 2400 units per hour. Capability to accurately measure high-efficiency conventional or backside-contact solar cells.
-
Product
Fuel Cell Hardware
-
The TP series cells are designed primarily for researchers who are providing their own MEAs, but they can be provided with MEAs as well. They can be offered as stand-alone cells, or as integrated equipment with our turn-key testing stations.
-
Product
Automatic Battery
BATLV360
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
Battery Testers
-
Traceable®Battery Tester checks alkaline, carbon, silver-oxide, mercury, nickel-cadmium, and other batteries. Tests battery voltages from 1.35 to 12 volts on 13 ranges. Accuracy is ±5%
-
Product
Battery Crush Test Equipment(Horizontal)
-
Guangdong Bell Experiment Equipment Co.,Ltd
Battery Crush Test Equipment(Horizontal)Application: Battery Module / Battery Pack / Battery System crush test, penetration test.Drive Mode: Electro-hydraulic ServoCrush Tool: Semi-cylinder, hemisphere (According to test standard)
-
Product
Battery Powered, Multi-Range, Analogue Portable Instrument
Tester SA9083
-
The Tester SA9083 is a battery powered, multi-range, analogue portable instrument. It is primarily intended for use by faultsmen for maintenance testing of telecommunication lines and equipment, subscriber installations connected to exchanges where faultsmen do not have access to a test desk, or where the testing equipment at the local exchange is not staffed during normal working hours. It has three input terminals, a range selector switch and a dual purpose push-button reversing switch (B-A changeover/test cell).
-
Product
Load Cells
-
A load cell is a sensor which transforms the load or force applied to it into an electrical signal. Load cell sensors are based on the strain-gauge principle i.e. a sensor whose resistance varies with applied force. They are the most widely used as load transducers in all areas of weight measurement from retail scales, the process industry and medical applications.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel
41-752A-001
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Your Automated Microscope For Live Cell Imaging
ZEISS Celldiscoverer 7
-
Combine the ease of use of an automated microscope with the image quality and flexibility of a research microscope. Whether working with 2D or 3D cell cultures, tissue or small model organisms, you will acquire better data in shorter times with this automated live cell imaging platform. Add LSM 900 with Airyscan 2 to gently image dynamic processes with highest framerates in superresolution.
-
Product
Flow Cell Kit
EQCMT
-
The two blocks of the EQCMT Flow cell are constructed using PEEK. It gives a high resistivity for chemical compounds.As well as QCM, these cell is reversible. With a inverted position of the blocks, it is possible to change from flow to static measurement.
-
Product
8-Channel VME Strain Gauge/Load Cell Module
V385
-
The V385 is a VME/VXI compatible eight-channel strain-gauge signal conditioner applicable to generic bridge-type transducer applications. The V385 adds individual remote-sensed excitation supplies to each channel, increasing its precision over the V380's single excitation supply.
-
Product
Battery Backup IC
-
Analog Devices offers a range of supervisory circuits that offer a complete single chip solution for power supply monitoring and battery control functions in microprocessor systems. Functions include microprocessor reset, backup battery switchover, watchdog timers, CMOS RAM write protection, and power failure warning.
-
Product
Digital 125 Amp Battery Load Tester
6033
-
• Heavy load enables the 6033 to detect bad batteries missed by other electronic testers• Automatically computes the CCA of the battery under load• Kelvin connected digital meter displays the following values:• Current Battery Voltage• Maximum Voltage reading• Minimum Voltage reading• Automatic load cycle• PATENTED• Made in USA of US and Global Components
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF1200
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralizedcompensation of power factor in low voltage instalations
-
Product
Power Bank Battery Testing System
BTS4000
-
Shenzen Neware Electronic Co LTD
Battery testing system for power banks(BTS-4000-6V4A-CCDC-USB) is based on Neware BTS4000, it shares all the main feature of BTS4000, such as 0.05%FS accuracy, 10Hz data acquisition frequency, based on Ethernet communication, etc.
-
Product
Permeability Cells
Flexible Wall Permeameter
-
The Permeability Cells - Flexible Wall Permeameter for Soil Samples performs permeability tests on normal and contaminated soil samples. The permeability cells are available either in brass for normal use or in stainless steel for contaminated materials. Top caps and pedestals are available for normal or contaminated materials.
-
Product
Unsealed Jacketed Electrochemical Cell – Temperature-Controlled
DL-1
-
DL-1 Unsealed Jacketed Electrochemical Cell – Temperature-Controlled is an electrochemical cell for laboratory research, designed for three-electrode testing, sealed or unsealed experiments, photocatalysis, corrosion studies, optical observation, or customized electrochemical workflows depending on the selected model. The cell can be matched with working electrodes, reference electrodes, counter electrodes, gas ports, quartz windows, PTFE covers, jackets, and custom fittings according to the experimental setup. Please confirm the required volume, sealing method, electrode ports, and application conditions before ordering.
