Impedance Meters
measure the rate of voltage to current in a circuit at a specified frequency.
See Also: LCR Meters
-
Product
FC Impedance Meters
-
designed for testing of the fuel cell with the small current (5 A or less), and not only the current-voltage characteristic test, the KFM2005 can easily measure for the impedance of a fuel cell using the AC impedance method, and the Cole-Cole plot. Using the measurement data of the Cole-cole plot, it is possible to calculate the circuit constant of the approximate equivalent circuit of the fuel cell. The built-in DC load (60W) is capable to operate from 0 V, and it can perform the test for the fuel cell up to 20V and 5A.
-
Product
Audio Generator & Impedance Meter
MR-PRO/MR2
-
The Minirator MR-PRO provides a full set of analog audio signals including sine wave, pink noise, white noise, delay test signal, polarity test signal, stepped sweep and continuous sine sweep. Further, a set of wav-files, useful for system optimization, is stored in the internal flash memory. Add your own personal favorites to this set.
-
Product
Vector Network Analyzers
-
RF VNA to a Broadband VNA, from a Premium VNA with the highest performance and no compromises to a Value VNA that offers solid performance with suitable measurement speeds for an R&D environment. No matter what your application, Anritsu has your VNA needs covered. Choose with confidence from the pioneers in VNA measurements, introducing the Wiltron 310 Impedance Meter in 1965, and introducing the first broadband VNA, spanning 40 MHz to 65 GHz, in 1999. The first to cover a span from 40 kHz to 125 GHz from a single coaxial connector.
-
Product
Impedance Meter, Audio, 200Ω, 2KΩ and 20KΩ scales
72-6948
-
Active device is essential for reliable installation of background music and paging systems in residences, offices buildings and public areas. Avoid costly service calls and amplifier damage by verifying actual speaker system impedance prior to operation. Unlike conventional volt/ohm meters, which measure DC resistance, this unit utilizes an internal 1KHz oscillator to measure true impedance. Accurately measure speaker lines that utilize impedance matching volume controls, switchers, transformers and passive crossovers. Because this unit accurately measures up to 20Kohm, it may also be utilized with 25V, 50V, 70V, and 100V speaker line transformers in commercial installations.
-
Product
Short Circuit Loop Impedance Meter
AMZC-305
-
Loop impedance measurement with resolution 0,01Ω ; Loop impedance measurement without tripping the circuit breaker > 30mA with resolution 0,01Ω (100...440V) ; Measurements possible in installations 110/190V, 115/200V, 127/220V, 220/380V, 230/400V, 240/415V, 290/500V and 400/690V (range 100...750V)
-
Product
Impedance Meter
ZM-100
-
Monacor International GmbH & Co.
Impedance meter for measuring the impedance (Z) of individual loudspeakers and loudspeaker lines.
-
Product
Short Circuit Loop Impedance Meter
AMZC-304
-
Short circuit loop impedance measurement in networks with nominal voltage: 220/380V, 230/400V, 240/415V, with frequency 45…65Hz ; Short circuit loop impedance measurement with 15mA current, without triggering RCD. ; Detection of the replacement L and N in the socket and automatic swap in the meter
-
Product
Precision Impedance Meter
1689
-
The GenRad 1689 Precision Impedance Meter gives you the best performance for your most demanding applications whether they be production test, incoming inspection, component design and evaluation, process monitoring or dielectric measurement. It is a versatile, full function microprocessor-based passive component tester that's available in a rack mountable, (1689M) model.
-
Product
Short Circuit Loop Impedance Meter
AMZC-306
-
Voltage measurement up to 750V and up to 250V with resolution 0,1V ; Measurements using Uni-Schuko adapter or test wires 1,2; 5; 10 and 20m ; Loop impedance measurement with resolution 0,01Ω and much more
-
Product
Battery Impedance Meter
-
Operation is fast and simple. Just press the spring-loaded probes onto the two poles of the battery. After 1.5 seconds, the unit beeps (indicating good contact) and displays the battery voltage and either the number of siemens or milliohms, depending on the knob setting. The display continues to show these numbers after the probes are removed; it resets only when the probes are pressed onto the next battery. The impedance and voltage of any battery between 1.2 and 60 volts can be read. Because of the wide range of voltages, even single low-voltage cells, such as NiMH, can be measured. The manufacturers of some batteries specify impedance in milliohms while other specify in siemens (one divided by the resistance in ohms). This meter will display both types of impedance for any given battery. Accuracy is +/- 2% of the value.
-
Product
Vector Network Analyzer
Bode 100
-
With the multifunctional Bode 100 you get an exact picture of your electronic circuits and components in a frequency range from 1 Hz to 40 MHz. The Bode 100 is not only a state of the art Vector Network Analyzer, it also works as: Frequency Response Analyzer, Impedance Meter, Gain Phase Meter, Sine Wave Generator.
-
Product
High Current Short Circuit Loop Impedance Meter
AMZC-310S
-
Measurement of very small short-circuit loop impedances (with resolution of 0,1mΩ) using the current of 150A under 230V, maximum 280A under 440V, or measurement using the current of 23A under 230V, maximum 42A under 440V
-
Product
Impedance Analyzer, 20 Hz to 10/20/30/50/120 MHz
E4990A
Impedance Analyzer
The E4990A Impedance Analyzer has a frequency range of 20 Hz to 120 MHz. The E4990A provides an industry best 0.045% (typical) basic accuracy over a wide impedance range, with a 40 V built-in DC bias source. The equivalent circuit analysis function supports seven different multi-parameter models and helps you to simulate your own equivalent parameter values of components.
-
Product
Analog Optical Power Meter - MATRIQ
1500 Series
Power Meter
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
Product
Capacitance Standard Set, 0.01uF To 10uF
16380C
Capacitance Meter
The 16380C is a standard capacitor set consisting of three precision capacitors - 0.01uF (16385A), 0.1uF (16386A), 1uF (16387A),and an optional 10uF (16388A). These capacitors are primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using these standards.
-
Product
Wavelength Tracker
10717A
Wavelength Meter
The Keysight 10717A Wavelength Tracker tracks changes in the air's index of refraction to optically compensate for environmental changes. It uses one axis of a laser measurement system to report wavelength of light changes, not changes in position. It is used to correct displacement values reported by other measurement axes in the system, hence improving measurement accuracy. It provides a higher degree of accuracy than environmental sensors such as the 10751C and 10751D Air Sensors.
-
Product
VDI Erickson PM5B MM–Wave Power Meter with W-Band Sensor, Optional Tapers to 1.5 THz
N1913PM5B
Power Meter
N1913PM5B is a Virginia Diodes, Inc./Erickson PM5B calorimetric mm-wave power meter, with a W-Band sensor for power measurement over a frequency range of 75-110 GHz.
-
Product
EPM Series Dual-Channel Power Meter
N1914B
Power Meter
The N1914B EPM series dual-channel average power meter provides repeatable and reliable results for bench/rack and field applications.
-
Product
100Hz/120Hz/1kHz/10kHz Handheld LCR Meter
U1732C
LCR Meter
20,000 counts resolution0.2% accuracy Wide LCR ranges with 4 selectable test frequencies (100Hz, 120Hz and 1kHz and 10kHz)Auto identification(Ai) which automatically determines and displays component type and measurements Detailed component analysis with ESR, Z, D, Q, functions Battery life of 16 hours/Ac-powered IR-to-USB connectivity for data logging to PC
-
Product
Analog Optical Power Meter - PXI
Power 1500 Series
Power Meter
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
Product
Multi-Wavelength Meter
86122C
Wavelength Meter
With an absolute wavelength accuracy of 0.2 ppm and 0.15 ppm differential accuracy, the new Keysight 86122C Multi-Wavelength Meter belongs in the top class of wavelength meters available for optical communication testing. Its wavelength range of 1270 to 1650 nm covers all fiber-to-the-home, metro and long-haul transmission systems. The instrument can measure the spectra of up to 1,000 laser lines at once, which is more than sufficient for fully populated dense-wavelength-division multiplexed systems (DWDM).
-
Product
Capacitance Meter
E4981A
Capacitance Meter
The E4981A capacitance meter offers a high-speed with reliable measurements for ceramic capacitor testing in the production lines. The E4981A realizes the measurement capabilities of capacitance from small to large values with accurate measurements. The E4981A capacitance meter contributes improvements of the test throughput, while attaining excellent component quality for ceramic capacitor testing.
-
Product
Digital Power Meter
Power Meter
Digital Power Meter is designed for single-phase measurements of AC power signals and related parameters common to most electronic products. Instead of traditional analog measurement circuits, the 66200 uses state-of-the-art DSP digitizing technology.
-
Product
P-Series Dual Channel Power Meter
N1912A
Power Meter
30 MHz video bandwidth Single shot real time capture at 100 M sample/s per second Key Measurements: - peak, average, peak-to-average ratio, rise time, fall time and pulse width22 Predefined formats: WiMAX, DME, HSDPA, etc. One screen view for pulse measurement analysis: Auto Scale, Auto Gate, Rise/Fall Time, Duty Cycle, etc. Internal Zeroing and Calibration while connecting to the DUT Bench Vue software enabled
-
Product
AC/DC Single Phase Digital Power Meter 100 kHz
T3PM1100
Power Meter
AC/DC Single Phase Digital Power Meter 100 kHz.
-
Product
EPM-P Series Dual-Channel Power Meter
E4417A
Power Meter
20 M sample/s per second sampling rate for reliable continuous and single shot measurements on wide bandwidth signals Time-gated and free run power measurements Free Analyzer Software software for complete pulse and statistical analysis, software is located In the Library8 pre-defined wireless configurations (GSM, EDGE, NADC, iDEN, Bluetooth, IS-95 CDMA, W-CDMA and cdma 2000)
-
Product
Optical Power Meter - MATRIQ
1400 Series
Power Meter
The Power 1400 Series optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 750 to 1700 nm. With a logarithmic amplifier, it avoids gain-jumps faced by multi-stage linear amplifier power meters.
-
Product
LCR Meter 10Hz - 100 kHz High Precision
T3LCR1100
LCR Meter
LCR Meter 10Hz - 100 kHz High Precision.
-
Product
Digital Power Meter
66205
Power Meter
The 66205 is the 2nd generation of the 66200 series power meter designed specifically for single channel measurement. Its state of art design is capable of providing highly accurate power measurements to meet the requirements of IEC 62301/EN50564 standards. Functionality improvements of the 66205 increase power measurement capabilities to a wider range of applications. The Smart Range function is one of the most important new features added to the 66205 power meter. Smart Range allows the power integration mode to perform active power measurements with the measurement range in auto mode. Chroma’s proprietary design automatically selects the appropriate range, based on changes in sensed voltage and current, ensures the best accuracy when integrating the measurements over time. The 66205 provides 10 selectable current measurement ranges from 5mA up to 30A. External sensor options A662017~A662020 are available to increase the current measurement range. Six selectable voltage ranges are available up to 600V.
-
Product
EPM Series Dual-Channel Power Meter
N1914A
Power Meter
Frequency range of 9 kHz to 110 GHz (sensor dependent)Wide dynamic range of -70 to +44 dBm (sensor dependent)Speed improvement by 2X for E-Series sensors: up to 400 readings/secGo beyond GPIB with LAN LXI-C and USB connectivity Code-compatible with E4418B, E4419B power meters*Code-compatible with 436A, 437B and 438A power meters (option 200)Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hosts Automated frequency/power sweep measurements with the optional external trigger in/out feature
