-
Product
Indoor Air Quality Monitoring
Si-AQ Expert
-
The Si-AQ Expert is the ideal tool for testing indoor air quality in warehouses and office buildings. It can measure concentrations of multiple different hazardous of gases and compounds that can affect air quality and worker safety.
-
Product
Monitoring Solar Panel Strings, DC 30A, Φ10mm
CTF-30-10DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Compact, Space-saving, Low Cost DC Current Sensors.・Split-core type, easy to apply to existing circuit.・Easy to use by unipolar +5V power supply.・High speed responsibility – less than 10μsec. 0 rated primary current.・Suitable for monitoring solar panel strings.
-
Product
Voice Monitoring
VOIP Echo
-
*The Voice Band Analyzer (VBA) is an analysis tool for monitoring the quality of voice band traffic (including hybrid echo) over VoIP, TDM and wireless networks*VBA works in conjunction with GL's TDM, Packet, and Wireless non-intrusive capture products, such as T1 and E1 Call Capture and Analysis, VoIP PacketScan&trade, and GSM, CDMA, and 3G Call Capture Products. VBA instantly detects voice file captures and with appropriately installed analysis modules, monitors speech levels, noise levels, and hybrid echo. Other analysis modules such as ITU-T P.561, P.562, P.563, fax and modem analysis, and many others can be hosted as plug-ins.*The VBA application can also operate on pre-captured files. It supports A-Law, µ-Law, 16-bit PCM (Intel), 16-bit PCM (Motorola) and MS Wave file formats.*Required software PKV100 and VBA032 at each probe location and PKV170 PacketScanWEB - Network Surveillance Software*Required hardware - 1U rack PC with sufficient hard disk for capturing over 10,000 calls (80 GB HD) for each VBA colocated with a probe*Additional hardware - PC for PKV100 PacketScan™ Software
-
Product
Dust and Opacity Compliance Monitors
-
LAND has a range of opacity, dust, smoke and particulates monitors which are the most advanced available, using patented measurement technology to give high accuracy. The analysers (which comprise a transmitter and a reflector) are mounted across the stack, the optical measurement technique uses no moving parts, giving the highest possible reliability with very low maintenance.
-
Product
Endpoint / Chamber Health Monitor based on Optical Emission Spectroscopy and MWL Interferometry
EV 2.0 Series
-
To address new requirements in Semiconductor, lighting devices, automotive components, flat panels, MEMS sensors, memory chips, and logic electronics processed in the industry using dry etch, cleaning and (PE)CVD, HORIBA has introduced a unique generation of sensor dedicated to Advanced Endpoint Control, Fault Detection and Chamber Health Monitoring.
-
Product
TDR Structural Health Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
Product
Monitors
-
The Gentec-EO monitors come in various sizes and types to cover all applications. We have monitors with or without display (PC-based) and for power or energy readings, or both. We also offer the fastest digital needle display on the market.
-
Product
HF / HCl Concentration Monitor
HF-960H
-
The HF-960H accurately measures concentrations of hydrofluoric and hydrochloric acid used in semiconductor manufacturing and other processes. The dedicated FES-510 series sensor is made from materials that are highly resistant to chemicals, making this unit ideal for the management of hydrofluoric and hydrochloric acid, even in high concentrations.
-
Product
Fume Hood Monitor
FHM10
-
Fume hoods are a primary source or protection in laboratories. Face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust hazardous chemicals. By accurately measuring face velocity and alarming on unsafe conditions, TSI’s FHM10 Fume Hood Monitors provide a high level of fume hood safety. And, the FHM10 helps users comply with standards and regulations set forth by OSHA, NFPA, ANSI Z9.5, and SEFA, calling for monitors to be installed on fume hoods.
-
Product
Kafka Monitoring With RTView®
-
RTView Enterprise provides turnkey Kafka monitoring with pre-built dashboards. With over 30 pre-defined alerts and over 15 pre-built monitoring dashboards, users can deploy quickly without the time, skill and expense necessary to build or configure their own monitoring applications or dashboards.
-
Product
Gas Monitor
ULTIMA® X5000
-
The ULTIMA® X5000 Gas Monitor is the future of gas detection for oxygen, toxic and combustible gases. MSA XCell® gas sensors with TruCal® technology offer calibration cycles up to 24 months (local calibration respected).
-
Product
Permanent Noise Monitoring System
831-NMS
-
The Model 831-NMS permanent noise monitoring system is designed for long term monitoring around airports, industrial facilities, motorsport complexes, wind farms, mining operations, and within the general community. Many required accessories are integrated through the INT docking station. Two way remote communication is available for monitoring and control from a central station. Larson Davis provides the hardware, software and open interface to allow this system to be customized for any application or purpose.
-
Product
Solution for Industrial Monitoring
PDScope
-
Techimp PDSCope is a brand new product of the PDCheck family particularly designed to suit all the requisites of the Techimp TiSCADA systems for on-line monitoring of diagnostic quantities in electrical assets.Techimp PDSCope is a powerful PD analyzer based on Techimp TF Map technology (patented) allowing preliminary noise rejection and automatic calculation of statistical parameters relevant to Partial Discharges.
-
Product
Portable 4-Gas Monitor
PS200
-
Teledyne Gas & Flame Detection
The PS200 Series combines quality, ruggedness and advanced technology in a user friendly, portable gas monitor. It is compact, lightweight, water resistant, extremely robust, and is certified to multiple international and regional standards.The PS200 can measure any combination of LEL, O2, CO and H2S making it suitable for a wide range of personal monitoring and confined space applications.In addition to extensive datalogging capabilities, the PS200 is available with an optional internal pump and an extensive range of accessories to meet a wide variety of user applications.Importantly, the PS200 has been designed to enable easier user maintenance which includes a fully automatic calibration station to simplify product compliance.
-
Product
DC Insulation Monitor
ISM-200
-
Kongter Test & Measurement Co., Limited
ISM-200 Insulation monitoring system is a high accurate and secure online monitoring equipment for DC system insulation. It is designed for the measurement of different types of ground fault, insulation decreasing, AC signal interruption, DC signal interruption and so on.
-
Product
Stand-Alone Type Chemical Concentration Monitor
CS-100 Series
-
The CS-100 Series offers a complete lineup of high precision chemical solution concentration monitors for various solutions in cleaning and etching processes during semiconductor manufacturing. In addition to the high-speed response and compact design, measurement of each component concentration is conducted in real-time and the timing of chemical solution changes and automatic supply is warned with an alarm. The ability to perform short measurement cycles allows for accurate monitoring of concentration changes.
-
Product
Snap-on RF Current Monitoring Probe
TBCP2-250
-
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
Product
Real-Time Content Monitoring System
ORION
-
Interra Systems' ORION is a real-time content monitoring system that enables service providers to deliver error-free, superior quality video. ORION provides real-time monitoring of IP-based infrastructures that looks at all aspects of video streams such as QoS, QoE, closed captions, ad-insertion verification, reporting and troubleshooting. ORION performs critical monitoring functions on hundreds of services simultaneously from a single platform, providing an operator with a single point of visibility and access to important information such as, status, alerts, alarms, visible impairments, error reports, triggered captures and more. ORION effortlessly monitors streaming content scaling single to multiple monitoring units/ sites across different geographical locations.
-
Product
Continuous Surface Current Mapping & Wave Monitoring System
SeaSonde
-
The SeaSonde HF radar system by CODAR Ocean Sensors is your solution for making continuous, wide-area ocean observations. The SeaSonde will provide you with years of real-time data over large coverage areas, with ranges up to 200 km — This is not possible with any other technology!
-
Product
Ground Fault Monitors
IFT
-
In most industrial settings, ground faults can cause significant damage. Since these leaks are unavoidable in almost all industrial environments, our ground fault monitors allow you to quickly and easily find the source of the leak before a major problem occurs and damages your equipment. The IFT-120 is designed to help you rapidly locate ground faults.
-
Product
Collapsible 6 Inch Charge Plate Monitor Assembly
CPM-760A
-
- 6" x 6" (15 cm x 15 cm) conductive plate- Total system capacitance of 20 pF ± 2 pF- Meets the requirements of ANSI/ESD STM3.1 and ANSI/ESD SP3.3- Designed to perform audits on overhead ionizers and room ionization systems- Flexible to also evaluate and balance bench top ionizers- Completely collapsible for compact storage- Designed to be used with the PFM-711A and PFM-711B
-
Product
Phase Monitors
-
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
Product
Intelligent Application and Service monitoring
Datadog
-
With turn-key integrations, Datadog seamlessly aggregates metrics and events across the full devops stack.*SaaS and Cloud providers*Automation tools*Monitoring and instrumentation*Source control and bug tracking*Databases and common server components*All listed integrations are supported by Datadog
-
Product
Monitoring System
TriGas X5000
-
The TriGas X5000 Monitoring System is an integrated gas detection solution that helps plant operators comply with NFPA 820. The system monitors for combustible gases, hydrogen sulfide and oxygen with on-board alarming and communication interface to plant and remote location control stations.
-
Product
Mobile Network Monitoring
NetMobility®
-
The next generation of mobile network monitoring is here. With NIKSUN NetMobility® you gain unparalleled insights into subscriber behavior, carrier services, network health, cyber threats, and application performance to meet a wide range of service provider needs - Performance, Security, Operations, Management, and Planning.
-
Product
Gamma Air Monitor
Quant Air
-
QuantAir is a solution for measuring radioactive contamination in the air, it provides high-performance detection capabilities with accurate in-field quantification.
-
Product
Condition Monitoring
Bearing Defender
-
The patented, wireless Bearing Defender provides instantaneous feedback on bearing health. It is user-friendly, can be used on just about any industrial machine, and detects bearing faults quickly and accurately.
-
Product
Spectrum Monitoring and Interference Systems
-
Automate wide area, close-proximity signal monitoring, interference detection, identification, location, reportingIncrease flexibility; set up rugged, portable-RF sensors in fixed, temporary or mobile platforms in any environment for extended periods of timeRemotely deploy a single sensor or a network of sensors synchronously country or city-wide, or in a roomCustomize for your application with software for spectrum monitoring, emitter location, signal intercept, capture/analysis
-
Product
VoIP Infrastructure Monitoring and Maintenance
NetVoice®
-
NIKSUN NetVoice® is the essential tool to monitor and maintain optimal network operation of your VoIP infrastructure. The NIKSUN solution monitors the network and alerts the administrator when abnormal network behavior or deterioration occurs, providing essential management and trending reports (periodic or on-demand) to plan for future network needs.
-
Product
15T Standard Running Line Monitor
RLM15T-3.0-S
-
The DLM 15T Running Line Monitor measures the tension on a rope passing through its three wheels. Typically used in cable laying and winch operations to measure and record line tension the robust design has become an industry standard. The monitor can be supplied as a separate item for integration with customers existing PLC’s or with a DLM digital display/HMI touch screen display.
