Loop Indicators
See Also: Indicators, Angle Position Indicators, Fault Indicators, Voltage Indicators
-
Product
Dial Indicators
-
1. Always select the dial test indicator that best fits the application.2. Care should be taken while using a dial test indicator, try not to jolt the indicator, should you be unfortunate and drop a dial test indicator, get it re-calibrated/repaired before reusing it.3. Replace worn contact points only with those of a similar length from the centre of the ball stylus to the abutment shoulder.4. Always clean dial test indicators after use with a lint free paper or cloth and store the indicator in its box or in a dust free area.5. When using a dial test indicator, always position the dial test indicator in a horizontal plane to the surface media.6. Always use a rigid stand for mounting the dial test indicator.7. When measuring a rotating object, either between centres or in a vee block, ensure that the object is rotating in the correct direction. Never rotate the workpiece towards the contact point.8. When measuring a sliding object, only take readings when the object is moving directly towards the contact point, never away from the contact point or in a sideways manner.9. Avoid parallax errors by reading the dial directly from the front and square on to the dial.10. Never oil a dial test indicator as this attracts contamination, should the movement become erratic then the dial test indicator should be submitted to a reputable repair agent.11. Try not to expose dial test indicators to direct sunlight or in a high humidity environment.12. Never use a dial test indicator that has not been calibrated, if in doubt consult an appropriate authority.
-
Product
Gas Accumulation Indicator
Qualitrol 038
-
Mechanical measurement of gas accumulation within a conservator style transformer. Alarm functions warn when level hits maximum limit and remains on until sufficient gas is removed. Sampling port allows your personnel to draw-off of gas for laboratory analysis.
-
Product
Load Cell Indicator
-
Morehouse Instrument Company Inc.
This indicator can read mV/V and use free, custom Morehouse software to convert the mV/V units to engineering units with coefficient files from ASTM E74 or ISO 376 reports. This meter is often the choice for accredited calibration service providers that want high accuracy and convenience but do not want to break the bank.
-
Product
RS485 Remote Display Indicator
CS1-8
-
CS1-8 has been designed for remote display by RS485 (Modbus RTU Mode) interface.
-
Product
Navigational Control Indicator
58LD1-01
-
- 3Ø AC input- 1 DC output plus AC lighting output- 100 Watt output- Operation up to 70,000 feet
-
Product
Loop Calibrator
6500 LC
-
Standard Electric Works Co., Ltd
● 4-20mA (1kΩ load, 24V Loop Supply).● 0.025% Basic Accuracy.● Simple Operation Interface.● Auto Ramp and Step Functions.● 0-20mA, 0-24mA selectable.● Incremental percentage setting : 0-100%.● Warning beeper when output is open.● 0-24V output.● The minimum load of 20kΩ on voltage mode.
-
Product
Vertical Speed Indicators
-
Is an instrument which indicates the rate of climb or descent of an aircraft.
-
Product
Phase Locked Loop (PLL) Synthesizer & Translation Loop
-
ADI’s industry leading phase locked loop (PLL) synthesizer family features a variety of high performance, low jitter clock generation and distribution devices. The extensive, ever growing family includes over 100 products, optimized for high data rate, low jitter clocking applications. The portfolio features PLLs, PLL/VCOs, and distribution chips, designed for clocking applications where synchronization, clock distribution, and phase noise performance are all vitally important.
-
Product
Bidirectional Weight Indicator
480
-
Large 0.8 in LED 6-digit Display• 100,000 displayed graduations• 523,000 internal counts• Powers up to 10 Load Cells• Tension/Compression operation• NEMA 4X stainless steel enclosure• Measurement Rate up to 40Hz• Selectable filter settings• 0.1uV/graduation signal sensitivity
-
Product
Indicators
-
Watlow Electric Manufacturing Company
Watlow''s temperature and process indicators are ideal for displaying measurements of temperature and other process variables; such as flow, pressure and relative humidity. They are moisture resistant and include bright, four-character LED displays, user-selectable temperature units, sensor break protection, agency approvals including UL®, CE, RoHS compliance and multiple mounting options such as DIN-rail or panel mount configurations.
-
Product
Temperature Loop Control Setup
ULP-27
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Temperature Control Loop Setup is basically a PC based PID controller setup used for closed loop and open loop analysis of temperature process system. The setup comprises of RTD temperature Sensor. The water flows through the Rotameter and Process tank to which a heating coil is fitted. The heater is controlled by a Thirstier drive. The Thirstier drive is connected to PID controller. The manual control valve can control the water flow. The system is mounted on a tabletop model with all necessary Piping. Water at approx. 100 LPH has to be supplied to a system externally. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
-
Product
Humidity Indicators
-
A humidity detector, also referred to as a humidity meter or humidity gauge, is a device with a humidity sensor that measures the relative humidity in the air. PCE Instruments offers a number of humidity detector products including handheld humidity detector, data recording or data logging humidity detector, and combination or multifunction humidity detector devices that also measure parameters such as room or ambient temperature and atmospheric or barometric pressure. A humidity detector can measure relative humidity (RH) as a percentage (%) from 0 to 100 % RH, depending on the humidity measurement range of the specific model.Humidity is a key factor in everything from library and museum archival to agriculture, construction, manufacturing, transportation, warehousing, and heating, ventilation, air conditioning and refrigeration (HVACR). A relative humidity meter also is helpful in evaluating workers' heat stress risk on production floors and job sites. In addition, humidity plays an important role in the residential sector. If the humidity is too high in a private household, mold can grow. Mold creates a health hazard for anyone breathing the air in the home.
-
-
Product
Digital Phase Locked Loop (PLL)
A6-CPS
-
The A6-CPS digital phase locked loop (PLL) can be customised to a specific application and shipped ready for use in production.
-
Product
Current Loop Expansion Kit
OP-SB85C
-
This expansion kit supports current loop communications.The kit incorporates a communications circuit with photo-coupler isolation and constant-current power supply of insulated type, thus realizing not only monitoring but also easy communications testing with passive or active current loop devices.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 16 Channel
43-765-001
Analog Output Module
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
-
Product
Dynamic Scale Deposition Loop System
-
Dynamic Scale Deposition Loop fully automated systems includes hardware and software to measure and evaluate the performance of scale inhibitors under high pressure and high temperature conditions.
-
Product
mA Loop Calibrators
-
Loop Calibrators are indispensable tools for process calibration professionals and we have just one you need. Choose from three different models depending on your need for accuracy and intrinsic safety. Each one is feature-rich and simple to operate and read.
-
Product
Square Root - Gauge Line Error Indicators
-
Parker PGI's SRE6 and GLE6 Indicators are designed to quantify Square Root and Gauge Line Errors in natural gas orifice flow measurement. They identify inaccuracies caused by compressor-induced pulsation and differential pressure discrepancies.
-
Product
Digital Closed Loop Control Thermal and Mechanical Testing System
3800 System
-
The Gleeble 3800 is a fully integrated digital closed loop control thermal and mechanical testing system. Easy-to-use Windows based computer software, combined with an array of powerful processors, provides an extremely user-friendly interface to create, run and analyze data from thermal-mechanical tests and physical simulation programs.The result is a system unequaled for physical simulation and thermal-mechanical materials testing.
-
Product
Freeze Temperature Indicator
TICT iS0°Tag®
-
The TICT iS0°Tag® can be used to monitor the temperature of any freeze-sensitive product such as vaccine, food, or specialty chemicals for up to 3 years.
-
Product
Magnetic Pole Indicator
-
identification of the field-direction of a magnet (north - south). It simply ascertains, fast and reliably the polarity of permanent magnets and electromagnets. This reliable device is simply to be served. It is indispensable for all industrial areas and fields of investigation which deal with magnetic applications.
-
Product
Remote Indicator System
LineTroll R110CQ
-
The fault indicator use a 2.4GHz ISM band short-range radio to communicate with the collector mounted on the pole. The collector communicates with up to 9 fault indicators. Both the indicators and the collector are powered by long-life lithium batteries for long and maintenance free operation.
-
Product
Line Loop Tester
8455
-
Simpson?s Model 8455 Line Loop tester detects line shorts, opens and multiple ringers, DC voltages and loop resistance. It can measure DC voltage up to 100 volts and loop resistance to 2 megohms. A front panel ?reverse polarity? switch allows changing polarity positions quicker and easier than manually switching test leads when making line checks.
-
Product
Antenna, Loop
EM-6879 | 10 KHz – 30 MHz
-
The EM-6879 Loop Antenna is used for magnetic field measurements over the frequency range of 10 kHz to 30 MHz. The EM-6879 is designed for use with any 50 ohm Receiver System. The antenna has a balanced Faraday shield that reduces its response to electric fields to a vanishingly small amount so that it can produce a practically pure magnetic field response.
-
Product
Indicators - Dial
-
Used for precise comparisons or measurements of workpiece surfaces, machine, equipment, part tolerances, alignment.
-
Product
Indicators
-
A device providing specific information on the state or condition of something, in particular.
-
Product
Trip Indicator Relays
TIR
-
The TIR relays are designed for event recording circuit applications, where high speed event monitoring is required. The TIR relay contacts are used to record breaker functions, relay, communication and control system operations. The TIR contacts are also used to activate alarm and/or annunciator contacts.
