Current Loops
See Also: Loop, HIL, Loop Testers
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
Three Loop Antenna
VVLA-30M
-
The three loop antenna VVLA-30M is a standard measurement antenna according to CISPR15-2005/GB17743-2007 standard
, it can work with LISUN EMI-9KA / EMI- 9KB EMI Receiver System for EUT magnetic field radiation measurement between X, Y and Z planes. The antenna measurement is accurate, switch conveniently and it can completely replace imported products. -
Product
DC BIAS CURRENT UNIT
3265B SERIES
-
To evaluate components at currents up to 125 A the 3265B DC Bias Units are used with either the Wayne Kerr 3255B series of Inductance Analyzers or the 3260B Precision Magnetics Analyzer. When one 3265B/25A or 3265BQ/25A DC Bias Unit is connected to an instrument up to 25 A of DC bias current can be set in steps of 25 mA with one unit. Additional DC Bias Units can be added such that with five units connected in parallel it is possible to set DC bias currents up to a maximum of 125 A DC.
-
Product
Modular Breakout System for Hardware-In-Loop Simulation
-
Designed in partnership with OPAL-RT Technologies, this Modular Breakout System combines a BoB feature set with the added flexibility of an FIU. By mating the FIU chassis directly to the BoB using our plug-in modules, cabling is minimized, creating a more compact reliable design and improving signal integrity.
-
Product
Current Transducer
IN 1000-S
-
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. 1000 A nominal, 3 ppm linearity over the temp. range, Very low offset drift 19.5 ppm, low noise 34 ppm peak-peak, -40 to +85°C, one compact package.
-
-
Product
Loop and Line Powered Level Switch
Safety IntelliPoint
-
The Safety IntelliPoint level switch provides a capacitance probe level switch with either a current output or relay contacts and “On-Board” self-diagnostics to ensure reliability. This SIL Intellipoint conforms to SIL 2 specifications providing the ultimate in level switch integrity and level sensing elements for a wide variety of temperatures, pressures, and materials.
-
Product
Short Circuit Loop Impedance Meter
AMZC-305
-
Loop impedance measurement with resolution 0,01Ω ; Loop impedance measurement without tripping the circuit breaker > 30mA with resolution 0,01Ω (100...440V) ; Measurements possible in installations 110/190V, 115/200V, 127/220V, 220/380V, 230/400V, 240/415V, 290/500V and 400/690V (range 100...750V)
-
Product
Pulsed Eddy Current (PEC)
Lyft®
-
Lyft is a high-performance solution reinventing pulsed eddy current (PEC). The patent-pending Eddyfi® solution features:
-
Product
Model QLS 4-20 mA Loop Splitter / Retransmitter
-
Generates up to four individually grounded and individually adjustable 4-20 mA loops from a single 4-20 mA or 0-10V input. Overcomes problems which occur when the same 4-20 mA signal is applied to multiple loads in series. Allows outputs to have different grounds, and allows individual loops to be opened without affecting signal to other loads.
-
-
Product
High Current Probe/DMM
655
-
Another great tool for all around electrical troubleshooting. The #655 is ideal for all high current applications, especially starting and charging diagnostics. The #655 can measure up to 1000 Amps AC or DC. Unit features built-in degrees F and C temperature readings.
-
Product
Current Injection
-
K&S Engineering and Scientific Ltd
The outputs are continuously variable from zero and are all isolated. The current outputs can be used at twice their continuous rated current on a 25% duty cycle with a maximum ON time of 5 minutes.
-
Product
Voltage, Continuity, and Current Tester
FLIR VT8-Series
-
The FLIR VT8-Series are high-quality voltage, continuity, and current testers. They feature an optimized, open-jaw design that can fit into tight spaces and reliably measure large-diameter cables. The VT8-600 carries a CAT III-600 V/CAT IV-300 V safety rating and a 100 A/600 V measuring range, while the VT8-1000 carries a CAT III-1000 V/CAT IV-600 V safety rating and a 200 A/1000 V measuring range. Extensive measurement features make the VT8-Series versatile tools – just one meter can get the job done.
-
Product
Current Probe For Non-Intrusive Measurement Of AC, DC, And Waveform Currents
CP 305
-
The CP 305 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.Using advanced Hall Effect technology the CP 305 can measure currents accurately up to 450A peak over the frequency range of DC to 20 kHz.
-
Product
Digital Current Integrator
-
The ORTEC Model 439 Digital Current Integrator was designed to accurately measure DC currents or the average value of pulse currents such as produced by accelerator beams. It digitizes the input current by producing an output pulse for specific values of input charge. A front-panel switch permit the selection of three different amounts of charge (10–10, 10–8 or 10–6 coulomb) required to produce an output pulse. The instrument has a digitizing rate from 0 to 10 kHz to provide wide dynamic range on each setting and high-resolution readout without meter interpolation.
-
Product
Single Loop Controller
1800+
-
The 1800+ controller is an evolved product from the West N8100. The product benefits from having more versatile features and user-friendly functionalities such as remote setpoint inputs, digital inputs, plug-in output modules, a customisable operator/HMI menu, jumperless and auto-hardware configuration, and 24VDC transmitter power supply.
-
Product
Zero Phase Current Transformer
MZL-65
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Split-core type for measuring zero phase current
-
Product
Multiparameter Current Meters
MIDAS ECM
-
The MIDAS ECM is one of only a few multiparameter current meters that allow real-time operations over several thousand metres of cable, as well as autonomous deployment.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-340L
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
Product
DC Leakage Current Monitor
MDLA-100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
This DC Leakage Current Monitor constantly observes leakage current of DC circuit like as PV generation system, etc. and lights up the warning lamp with signal output, when the leakage current exceeds the setting value.
-
Product
Precision Multirange Current Transformer
P-5000
-
The P-5000 transformer is a laboratory standard. The unit’s excellent accuracy and the Knopp One-to-One calibrating feature make this precision transformer well-suited as a standard for calibration work. This transformer can provide a very accurate determination of the ratio and phase angle characteristics of current instrument transformers having ratios from 5 to 5,000 amperes. This transformer also can accurately extend the range of a 5 ampere ammeter or wattmeter to cover all current values up to 5,000 amperes.
-
Product
Zero Phase Current Transformer
MZL-45
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Split-core type for measuring zero phase current
-
Product
Split type Pulse Current Sensor
CTF-05
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
High accurate AC pulse current sensor for power demand meter.
-
Product
DC Bias Current Source
FD1772B
-
• Constant DC output 0-6A• Auto or manual current sweep output• 5 current range output• Output voltage range: 0-11.5V• Current accuracy ± (1%reading + 2digit)
-
Product
Current Integrated Sources
CIS
-
The CIS current integrated source was designed to provide a stable alternating current source for the electricity meter test equipment, and in laboratories. The output current is isolated and independent from the mains voltage. Different CIS versions are available depending upon the values of output power and output current required.
-
Product
Bluetooth Recording Current Meter
RCM Blue
-
A self-recording dedicated current meter with Bluetooth for communications and data retrieval - now with the possibility to integrate a pressure sensor!The RCM Blue is a self-recording Current Meter which also measures water temperature in salt or fresh water, and a battery container with battery capacity up to 70Ah. .The Doppler Current Sensor is an upgraded version of the proven SeaGuard ZPulse sensor. The RCM Blue instrument configuration and data retrieval is done via Bluetooth which eliminates the need to open the pressure case for repeated deployments.RCM Blue has now been upgraded with the possibility to integrate a pressure sensor with a 0,01% accuracy. This simplifies your work significantly as you will know exactly where you are in the water column.
-
Product
Field Current Regulator
-
We are counted amongst the leading names in the industry, offering wide range of Field Current Regulator. Our entire product line ensures easy operations and is performance based. Field Current Regulator are quality tested and are delivered in standard configurations. Our entire product range has high strength and is delivered at most affordable rates.
-
Product
Current Sources
-
Innovar Current Sources are the standard in the circuit breaker industry. Our Current Sources supply regulated current from 1 amp to 100,000 amps with incredible accuracy, along with providing a full set of features that is unmatched by any other Current Source in the market.
-
Product
High Current Discharge Testing System
DTV
-
Cold Crank Testing to industry standards: IEC, SAE, BCIDischarge capacity performance testing to thousands of amperes
