VMEbus
VERSAmodule Eurocard bus
-
Product
VMEbus Repeater Link
VME-REPEAT-A-L
-
The VME-REPEAT-A-L is a two-board set which allows VMEbus slave I/O boards residing in one VMEbus chassis to be controlled by a VMEbus master residing in another chassis. The VMEbus chassis in which VMEbus masters reside is referred to as a master chassis, while the VMEbus slave boards reside in a slave chassis.
-
Product
VMEbus
-
VMEbus (Versa Module Europa bus) is a computer bus standard widely used for many applications and standardized by the IEC as ANSI/IEEE 1014-1987. First developed in 1981 and continues to see widespread use today.
-
Product
6U Form Factor PMC/PrPMC Carrier-VMEbus
i4400
-
The i4400 is a low-cost 6U form factor PMC / PrPMC carrier for the VMEbus and forms the basis of a flexible I/O system. It offers the user a means of integrating two single PMC modules or one double PMC module in a VMEbus system. The current version of the i4400 supports PMC modules and also supports Processor PMC modules on one PMC-site. The VME-to-PCI bridge is implemented in an FPGA for flexible VME-to-PCI mapping and to allow future updates and upgrades.
-
Product
RTD Measurement for VMEbus
VME390
-
The VME390 features 24 two, three or four wire high-accuracy PT100 measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued.
-
Product
CANbus Controller for VMEbus
VME360
-
The VME360 CANbus controler is a 6U VMEbus board based on four SJA1000 CANbus controllers. Each SJA1000 provides an interface to the popular CANbus that supports both standard (11-bit) and extended (29-bit) identifier fields. Front panel LEDs provide diagnostical network information. The VME360 provides four CANbus interfaces. The CAN network is a serial communication protocol which efficiently supports distributed control with a high level of reliability.
-
Product
M-Module Carrier for VMEbus (6U)
i4000
-
The i4000 is a 6U form factor M-module carrier for the VMEbus and forms the basis of a flexible I/O system. It offers the user a means of integrating a mix of M-modules in a VMEbus system. Four M-module mounting sockets are provided by this carrier.The interrupt controller on the i4000 has an interrupt vector register for each M-module interface.
-
Product
Stepper Motor Controller for VMEbus
VME321
-
The VME321 Intelligent Stepper Motor Controller with Amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications.This VMEbus board has a 6U form and is also available as 3U VMEbus board.
-
Product
VME-Bus Synchro - Resolver LVDT I/O Cards
VB Series
-
Computer Conversions Corporation
The "VB Series" product lines contains VME compatible synchro/resolver converters and absolute encoder systems. These particular cards are ideal for any rotary motion and related process, control, or simulator type application with any VME compatible system.
-
Product
VME Modules
-
VME is a high speed and high performance bus system with powerful interrupt management and multiprocessor capability. It was created by combining VERSA-bus electrical specifications (1979) with the Euro-card format resulting in the VME-bus Revision A - 1981 specification.
-
Product
VME 3U
129-130-30-31
-
Hartmann Electronic is an industry leader in the designing, manufacturing and production of backplane technology, including VME and VME64x. Over the evolution of its near 40 years of existence, VME-bus has become a worldwide standard and is still used in a wide variety of applications across many different markets.
-
Product
Universal Timer/Counter for VMEbus
VME385
-
The VME385 Universal/Timer Controller VMEbus board is an ideal solution for automated test and measurement applications. The VME385 features eight timer/counter inputs, all inputs have an coaxial connector for the input range of +/- 10 V and high-voltage pins for the input range of +/- 300 V. The coupling of the inputs is either AC or DC. The VME385 provides 6 measurement functions: frequency, high-time, low-time, period, counter and phase measurements.
-
Product
16/8 Channel 14 bit 500 MS/s Digitizer
VX1730 / VX1730S
-
The VX1730S comes in a VME64X form factor, with 16/8 input channels. The communication to and from the board is provided through the VMEBus and Optical Link interfaces. The VX1730S (previously VX1730) has also been upgraded, introducing a larger FPGA to accommodate more complex DPP algorithms and a new A/D converter for better stability which does not require temperature-related calibration.
-
Product
Serial Controller
PMC522
Controller
The PMC522 provides a uniquely effective solution for integrating serial I/O requirements into a VMEbus or CompactPCI system. Implemented on a single PMC card, the PMC522 is fully compatible with the current generation of VMEbus and CPCI single board computers, as well as any special purpose processor that includes a PMC connector.
-
Product
ME-4C ARINC-429 Controller VMEbus
IIB-429-VME-4C
-
The IIB-429-VME-4C provides 16 ARINC-429 compatible channels (8 receive and 8 transmit) at any rate between 12.5 and 100 kbps. Because the IIB-429-VME-4C is built upon a flexible platform, user functions can be implemented almostwithout restriction, making this product flexible and user-friendly.This VMEbus board has a 6U form factor.This VME unit is also available in a 3U form factor, as IIB-429-VME.
-
Product
64 Channel ADC for VMEbus
VME392
-
The VME392 features 64 self-contained ADC channels with a resolution of either 12 or 16-bit (see ordering information). This product is ideally suited for mass acquisition with high accuracy for reasonable cost. The 64 channels are grouped into four sections of 16 channels each. Each section behaves completely independent from the other sections.
-
Product
Powered VME Crates
-
VME is a high speed and high performance bus system with powerful interrupt management and multiprocessor capability. It was created by combining VERSAbus electrical specifications (1979) with the Eurocard format resulting in the VMEbus Revision A - 1981 specification. The VMEbus specification has since then been refined through revisons B (1982), C, C.1, IEC 821 & IEC297 and IEEE 1014-1987.
-
Product
VME-VME64 6U 162
-
Hartmann Electronic is an industry leader in the designing, manufacturing and production of backplane technology, including VME and VME64x. Over the evolution of its near 40 years of existence, VME-bus has become a worldwide standard and is still used in a wide variety of applications across many different markets.
-
Product
2 Channel 10 bit 4GS/s Digitizer
VX1761
-
The VX1761 comes in a VME64X form factor with 2 input channels. The communication to and from the board is provided through VMEBus and Optical Link interfaces.
-
Product
64 Ch Peak Sensing ADC
V1741
-
The V1741 is provided with drivers for the supported communication interfaces, C libraries, demo software for an easy board understanding. Firmware upgrade can be performed via optical link or VMEbus by the user.
-
Product
Interface
RMAC-VME
Interface
Designed for laboratory simulation and production test applications, the Modular Avionics Controller (RMAC) is an intelligent, high performance 6U VME product supporting ARINC protocols and other serial communications. As an evolutionary follow-on product to the successful VME-AIC product line, the RMAC-VME provides a single integrated interface to multiple avionics protocols on VMEbus platforms.
-
Product
8 Channel 14 bit 100 MS/s Digitizer
VX1724
-
The VX1724 comes in a VME64X form factor with 8 input channels. The communication to and from the board is provided through the VMEBus and Optical Link interfaces. The VX1724 is a digitizer able to record waveforms along with performing advanced algorithms for online digital pulse processing (DPP) of pulse height analysis and dynamic acquisition window.
-
Product
VME / VME64x Backplanes
-
Hartmann Electronic is an industry leader in the designing, manufacturing and production of backplane technology, including VME and VME64x. Over the evolution of its near 40 years of existence, VME-bus has become a worldwide standard and is still used in a wide variety of applications across many different markets. Hartmann’s innovation in cost effective design benefits customers in diverse industries including military, transportation, medical imaging, telecom, industrial controls, and aerospace.
-
Product
VME64x Form Factor Extender, 6U x 60mm
116FFE6006-012X
-
The VME64x form factor extender 6U 60 mm allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
-
Product
PMC/XMC Expansion Card
EXP238
-
The EXP238 is a 6U VMEbus form factor expansion card offering three XMC/PMC expansion sites. When ordered as an option for the XVB603 VMEbus single board computer, the 3-slot solution greatly expands system flexibility.
-
Product
Serial Controller
PMC522/FP
Controller
The PMC522/FP provides a uniquely effective solution for integrating serial I/O requirements into a VMEbus or CompactPCI system. Implemented on a single PMC card, the PMC522/FP is fully compatible with the current generation of VMEbus and CPCI single board computers, as well as any special purpose processor that includes a PMC connector.
-
Product
VP F6x/msd, 6U VME processor board
VP F6x/msd
-
VP F6x/msd is a 6U VME processor board designed to extend the life for VMEbus deployments by using the tried and tested Universe-II VME bridge. It is based on a 4-core Intel® Xeon® E3-1505L v6 processor.
-
Product
VME Power Supply
-
VME is a high speed and high performance bus system with powerful interrupt management and multiprocessor capability. It was created by combining VERSA-bus electrical specifications (1979) with the Euro card format resulting in the VME-bus Revision A - 1981 specification. The VME-bus specification has since then been refined through revisions B (1982), C, C.1, IEC 821 & IEC297 and IEEE 1014-1987. VME represents one of today's most used industry bus .
-
Product
Expansion Card
PMC238
-
The PMC238 is a 6U form factor card that expands a single PMC site on a VMEbus processor board to two PMC sites and one PCMCIA/CardBus socket or to three PMC sites. Compatible with many VMEbus single board computers, it provides an extension of PCI and PCMCIA capacity within the VMEbus form factor. The PMC238 has the option for the PCMCIA/CardBus cards to be mounted outside the chassis using an 18-inch cable.
-
Product
Digital Input Board
VME-1128
Digital Input Board
VME-1128 is a 128-bit High-Voltage Digital Input Board with Built-in-Test. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297) with the following mnemonics: A24:A16:D32/D16/D08 (EO): Slave: 39/3D:29/2D Form factor: 6U
-
Product
4/8 Channel 10 bit 2/1 GS/s Digitizer
VX1751
-
The VX1751 comes in a VME64X form factor with 4/8 input channels (4 channels in case of DES mode*). The communication to and from the board is provided through the VMEBus and Optical Link interfaces.
