CompactPCI Chassis
A metal frame that serves as the structural support for a CompactPCI bus. (sbc.webopedia.com)
-
Product
6 Slot PXIe Based Chassis with Embedded Controller
PXE6410
Chassis
The PXE6410 is a PXIe based 6 based slot Gen 3 x4 chassis, that supports the Tabor Proteus Family of AWG’s and the TE330x family of PXIe RF amplifiers. The Chassis allows you to purchase any Proteus PXIe module and later add or up-grade to more channels, higher sample rates or higher output power.
-
Product
PXIe-1090, Thunderbolt™, 2-Slot (1 Hybrid Slot), Up to 2 GB/s PXI Chassis
787040-01
Chassis
PXIe, Thunderbolt™, 2-Slot (1 Hybrid Slot), Up to 2 GB/s PXI Chassis - The PXIe‑1090 features a high-bandwidth backplane to meet high-performance test and measurement application needs. This PXI chassis features one hybrid connector, 58 W power and cooling, and an integrated. Thunderbolt 3 MXI-Express controller. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the US and/or other countries.
-
Product
Chassis 8 Slot
PXIe 4U/ 42HP
Chassis
As PXI has evolved into high-speed serial fabric technology, so has the Hartmann Electronic product line with the addition of its PXIe solutions. More power, more bandwidth, more functionality.
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
781496-01
Chassis
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
Chassis - Control Relays Greater than 8x1 or Control Multiple Relays in Series Forming Larger Switches than Normally Possible Such as 16x1 to 32x1 Sections.
CXM/256-MF
Chassis
These Chassis are typically used to control relays greater than 8x1 or control multiple relays in series forming larger switches than normally possible such as 16x1 to 32x1 sections. Or control mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 256 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
-
Product
4U Rackmount Chassis For Full-Size SHB/SBC Or ATX/MicroATX Motherboard With 4 Hot Swap Drive Trays
ACP-4340
Chassis
Supports a PICMG backplane with up to 14 slots or an ATX/Micro-ATX motherboardShock-resistant disk drive bay holds four hot-swap 3.5" and 2.5" SATA disk trays, one slim optical disk drive, and one 2.5" internal driveDual front USB 3.0 portsFront-accessible system fan without opening top cover for easy maintenanceLED indicators and alarm notification for system fault detectionBuilt-in Intelligent System Module enabling whole system fan control and remote manageability
-
Product
Mainframe or -E Expansion Chassis - Preconfigured Single or Two Pole Matrix Systems
LXB/128-MF
Chassis
These Chassis are preconfigured single or two pole matix systems. A single chassis can be a 16x8 matrix, two 16x4 matrices, a single 32x4 or a single 64x2 configuration. Chassis is modular so you may start with a smaller size and increase the configuration as your needs grow.
-
Product
6U CompactPCI
-
Advantech offer 6U CompactPCI CPU boards, rear transition modules, peripheral boards, and support for PMC or XMC module.
-
Product
CompactPCI 4 Slot 2U
-
2U, 19″ Rackmount system with up to two hot removable CPCI 3U Power Supplies, three Powerful Fans and CompactPCI Backplane. The system support 6U cards Front and Rear. Additional three fans are available for optimal Front and RTM cooling solution. The Backplane is compliant with PICMG 2.0 R3.0 with 64bit 66MHz and supports boards with hot swap capability PICMG 2.1 R2.0. All five CompactPCI connectors (J1-J5) are available on the backplane. The system slot is located on the lower-slot. A backplane supporting PICMG 2.16 & H.110 are available on request.
-
Product
CompactPCI
cPCI4IP
-
The cPCI [CompactPCI] compatible cPCI4IP design adds 4 Industrypack compatible slots to your cPCI host. The cPCI4IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI4IP is a 6U 4HP cPCI design with 4 IP slots.
-
Product
CompactPCI PICMG 2.16 Backplanes
-
Comtel Electronics offers a large variety of CompactPCI 2.16 Backplanes, 8 – 14 slots 64 bit 33Mhz,Fully compliancy with PICMG 2.0 Rev 3.0 Specs & 2.16 Spec. Hot Swap compliant per PICMG 2.1 R2.0 Spec.
-
Product
CompactPCI Interface Card
CPCIC-1553/PXI
Interface Card
The CPCIC-1553/PXI Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Our Card and Software Packages are Designed for Fast, Portable Integrations. The CPCIC-1553 is the Only Commercial Off the Shelf (COTS) Card that Passes and Executes the SAE AS4111/4112 Protocol Tests.
-
Product
Stepper Motor Controller for CompactPCI
CPCI321
-
The CPCI321 Intelligent Stepper Motor Controller with amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead.
-
Product
CompactPCI 14+2 Slot
-
The CompactPCI® 14 CPCI slot + 2 PSU slot backplane uses CPCI bridging to enable 2 PCI segments.
-
Product
Desktop/Wallmount Chassis
IPC-7130L
-
Desktop/Wallmount Chassis for ATX/MicroATX Motherboard with Dual Hot-Swap 3.5" Drive Bays. Shockproof drive bays - One 5.25", one internal 3.5", and two hot-swap 3.5" trays for IPC-7130 / two 3.5" HDD device trays for IPC-7130L. Lockable front door prevents unauthorized access, LED indicators for system fault detection.
-
Product
NI-9145, 8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis
784756-01
Chassis
8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis - The NI‑9145 is a rugged EtherCAT slave chassis for adding deterministic, distributed I/O to any CompactRIO, PXI, or industrial controller with two Ethernet ports. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. You can daisy chain multiple NI‑9145 slave chassis from the master controller to expand time-critical applications to higher channel counts while maintaining hard determinism with minimal processor resources.
-
Product
8-Slot ShoeBox Chassis
AX60552
-
*Two 5.25 and one 3.5 HDD drive bays*Desktop or wallmount industrial computer chassis*Equipped with PS/2 type power supply
-
Product
VPX / OpenVPX Chassis
-
VPX is a broadly defined technology utilizing the latest in a variety of switch fabric technologies in 3U and 6U format blades. Open VPX is the architecture framework that defines system level VPX interoperability for multi-vendor, multi-module, integrated system environments.
-
Product
PXIe-1062Q, 8-Slot, Quiet, Up to 3 GB/s PXI Chassis
779633-01
Chassis
8-Slot, Quiet, Up to 3 GB/s PXI Chassis—The PXIe‑1062Q is designed for a wide range of test and measurement applications and provides a high-bandwidth backplane. The NI PXIe‑1062Q has four PXI peripheral slots, one PXI Express slot with system timing capabilities, and two PXI Express hybrid slots that accept both PXI and PXI Express peripheral modules.
-
Product
6-slot Chassis
CH-06 AXIe-0
-
The 6-slot chassis in AXIe-0 format is intended for use in modular measurement information systems based on the AXIe standard.
-
Product
3U Chassis
-
3U chassis supports comes in 3U 16 Bay and wide selection of single and redundant power supply. 3U chassis provides surveillance storage and short-depth design that saves spaces and can be stored in tower, rackmount and wallmount.
-
Product
Industrial Chassis
-
Axiomtek's industrial chassis are flexible, easily managed, and feature solid designs. Axiomtek also provides a customized ID program in a short amount of time. Axiomtek satisfies various customers' need by supplying the right type of chassis designed for the right applications.
-
Product
Chassis
-
Infrastructure housing for instrument cards typically containing a power supply, cooling fans and emi shielding.
-
Product
8-Slot 64-Bit 6U CompactPCI Backplane
cBP-6408R
Backplane
- PICMG 2.0 CompactPCI Specification R3.0 Compliant- PICMG 2.1 CompactPCI Hot Swap Specification R2.0 Compliant- PICMG 2.5 H.110 Computer Telephony Specification R1.0 Compliant- Design for 64-bit/33MHz CompactPCI computer system application- One system slot with seven expansion slots, system on right hand side
-
Product
Chassis and Safety ICs
-
ST is a world-class supplier of IC smart power solutions for all the Chassis and Safety applications, ranging from passive safety, braking, vehicle dynamics and steering systems. Type of devices in ST portfolio are analog and mixed-signal ICs, integrating different functions such as supply modules, drivers for loads and actuators, diagnostic functions, system monitoring and communication interfaces.
-
Product
1U Chassis
-
The 1U chassis support multiple configurations include SATA hard drives, rackmount chassis and redundant power supply that fulfill server-grade IPC standard. The 1U chassis series with the cooling fans design to deliver non-stop operation.
-
Product
Chassis Dynanometer for Motorcycle
-
•Adopted FAMS-R5 system for motorcycle chassis dynamometer•Gas emission test, durability test, performance test, and environmental test are applicable to various vehicles (motorcycle, tricycle,ATV).•Newly designed measurement unit in a test room makes measurement easier.•Reduction of initial cost, space saving, and less maintenance items by lineup of electric inertia type chassis dynamometer that can be used for small to large vehicles.•Components necessary for emission test are included, such as front wheel holding unit, engine cooling fan, drivers display.•Application software necessary for emission test is installed, such as road resistance setting software, drivers aid,gas emission data processing software, rear axle output data processing software.
-
Product
MIL-STD-1553 CompactPCI Interface Card
CPCIC3/6-1553-PXI
Interface Card
The CPCIC-1553/PXI Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Our Card and Software Packages are Designed for Fast, Portable Integrations. The CPCIC-1553 is the Only Commercial Off the Shelf (COTS) Card that Passes and Executes the SAE AS4111/4112 Protocol Tests.
-
Product
Chassis and Controllers Accessories
-
Keysight offers high-performance chassis and controller accessories to synchronize multiple Keysight USB modular products to accelerate your test system integration and development.
