Polarization Mode Dispersion
Polarization Mode Dispersion
-
Product
Polarization Controller and Scrambler - PXIe
Pol 1000 Series
Controller
The Pol 1000 Series PXIe module enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands. Pol 1000 Series can be used with our wide range of optical and electrical PXIe test modules, and can be used to build complete mixed-signal test platforms.
-
Product
RS422 Mode SI-module With Optical Isolation And RTS/CTS
MX422-PEP
-
RS422 mode SI-module with optical isolation and RTS/CTS
-
Product
Polarity Indicator Circuit Tester
CT8007
-
No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance electronic circuitry. Negligible current draw ( 1 microampere) is 30,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 6 and 28 Volt DC in battery powered systems
-
Product
PXI Dual 2 x 2 Fibre Optic (M Mode) SC M62.5
40-860-222-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
LXI 8:1 Optical MUX FC/APC Single Mode
60-850-011
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI Single 2 Channel (M Mode) SC 62.5 Cons
40-855-212-M62.5
Switch Module
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
Product
PXI Single 2 Channel (M Mode) SC 50 Cons
40-855-212-M50
Switch Module
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
Product
Energy Dispersive Spectroscopy (EDS) Detector Technology
EDS
-
The Element SDD is a solutions based detector, which excels at basic analysis. Focused primarily on serving the needs of the industrial market segment, it provides application specific software and analysis that can quickly provide answers in the industrial environment.
-
Product
PXI Dual 2 x 2 Fibre Optic (M Mode) ST M50
40-860-522-M50
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI Single 2 Channel (M Mode) ST 62.5 Cons
40-855-512-M62.5
Switch Module
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
Product
EBIRST Slave Mode Connection Cable
93-970-301
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Single Mode Multimode Test Inspect Kit
KI-TK072A
-
1310/1550/1625 nm & 850/1300 nm source & Autotest power meter + acceptance reporting software, inspection microscope, cleaning materials. Interchangeable SC/APC & LC/APC connectors
-
Product
Single Mode & Multimode Test Kit
KI-TK037
-
1310/1550 nm & 850/1300 nm source & power meter, inspection microscope & cleaning materials with Interchangeable SC & LC connectors
-
Product
Hardened Media Converter, 100Mbps, Single Mode 1310nm, 30km, SC
EKI-2541SI
-
Provides 1 x 10/100 Mbps Ethernet port with RJ45 connectorProvides 1 x 100 Mbps Single-mode SC type fiber portProvides internal jumper for Link Fault Pass-through (LFP) settingSupports full/half duplex flow controlSupports store and forward transmissionSupports auto-negotiationSupports MDI/MDI-X auto crossoverSupports redundant 12-48 VDC power inputProvides flexible mounting: DIN-rail and Panel mountSupports wide operating temperatures from -40 to 75°C
-
Product
Polarization Management
-
Control and manage polarization in your optical system with our lossless, fiber-squeezer-based, multifunctional polarization controllers to achieve the highest performance. Emulate all polarization impairment parameters including SOP, PMD, and PDL, with our complete industry-standard line of emulation products for network and system characterization.
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Firmware for High-speed HDLC Mode
OP-FW10G
-
OP-FW10G is an expansion firmware to upgrade LE-3500 measuring Bit-Synch (HDLC/SDLC/X.25/CC-Link) and SPI communications up to 10Mbps. Hardware processing by FPGA built in the analyzer makes it possible to capture data with time stamp at micro second. It is useful to analyze SPI communications and High-speed HDLC communications such as RS-485 multi-drop CC-LINK and TTL signal level on the printed-circuit board.
-
Product
RS232 Mode SI-module With Optical Isolation
MX232-G
-
RS232 mode SI-module with optical isolation
-
Product
Polarization Maintaining Band Pass Filter
-
Zhongke Rayzer Optical Technology Co.,Ltd
Selects the thin film filter withgood performance to ensure the high quality opticalperformance, stability and reliability. It is uses to shieldnoise signal in EDFA and fiber laser system. It has thecharacteristics of high isolation, low insertion loss, highreturn loss and high power.
-
Product
Polarisation Mode Field Diameter
MA500
-
MA500 is our polarisation mode field diameter (MFD) and effective area (Aeff) measurement system, specially designed to measure large effective area and high NA single mode fibers with its enhanced dynamic range and high-resolution scanning optics.
-
-
Product
Energy Dispersive X-ray Fluorescence Analyzer
X-5000
-
HORIBA continues it's innovation in the petroleum market by proudly teaming with Olympus Innov-X to promote the X-5000 Mobile XRF Analyzer. The X-5000 is a rugged, fully integrated closed beam portable EDXRF system that offers the power and performance of a traditional benchtop XRF, but is designed for transportable operation.
-
Product
4 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTC
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
PXIe Very High Density Multiplexer, 2A, 79-Channel, 2-Pole, Single Channel Mode
42-611B-002
Multiplexer Module
The 40-611B-002 (PXI) and 42-611B-002 (PXIe) modules are 79-Channel 2-Pole multiplexers. A 158-Channel 1-Pole configuration is also available.They use high quality electro-mechanical signal relays allowing switching up to 2 A and voltage up to 300 VDC/240 VAC. They are suitable for signal routing in high channel count ATE and data acquisition systems. Connections are made via a front panel 160-pin DIN 41612 connector.
-
Product
Mixed Mode Testing
-
The Mixed Mode add-on modules for the Random Vibration Control Software allow tests to run with sine tones and/or narrowband random signals superimposed on a random background. Mixed mode testing is a complex control task, and m+p VibControl supports three modes: Sine-on-Random (SoR), Random-on-Random (RoR) and Sine-on-Random-on-Random (SoRoR). Gunfire burst control can also be superimposed in each case.
-
Product
Polarization Extinction Ratio Measurement
-
Rapid & Accurate measurement for PER, Angle, and Power. The most suitable light source for PER measurement.
-
Product
Time Domain Induced Polarization /Resistivity Receiver
IPR-12
-
This allows you to troubleshoot and monitor data quality for the most efficient IP survey possible. With an IPR-12 you will have an excellent tool to get the best possible IP data from your survey.
-
Product
PXI Dual 2 Channel (M Mode) ST 50 Cons
40-855-522-M50
Switch Module
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode) SC M50
40-860-212-M50
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI Dual 2 Channel (M Mode) SC 50 Cons
40-855-222-M50
Switch Module
The fiber optic switches connect the common to a channelby redirecting the optical signal into a selected output fiber.This is achieved using Micro-Mechanical Mirrors driven bya highly precise mechanism and activated via an electricalcontrol signal.
