Time
is an illusion of duration.
See Also: Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Timing, Counter / Timers, Atomic Clocks, Phase
-
Product
Kestrel /QX
0149-QX
-
Quad+ speed Windows/NT Kestrel Co-Processor for four times the speed of the Kestrel /SX. Occupies one PCI slot. A writable control store, FPGA implementation of the HP1000 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes compatible hardware floating point. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. PCI bus speeds increase disk throughput by at least a factor of ten. HP1000 Bus support logic for non-emulated devices is provided on-board with connector to wide bandwidth fibrechannel adapter. Operates only under Windows/NT. WNT Support license included.
-
Product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
-
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
Product
Networking Solutions
Thread
-
Thread is an IPv6-based mesh networking protocol designed as a reliable, low-power, secure, and scalable networking solution for connecting Things to the IoT. As a founding board member of the Thread Group, Silicon Labs helps accelerate time to market with proven mesh networking hardware and software solutions.
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
781496-01
Chassis
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
GPS Modules
-
A GPS module is a receiver that uses signals from satellites to determine location and time, while a GPS modem is a more complete device that combines a GPS receiver with a modem (like a GSM or cellular modem) to send that location data over a network.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 2 Channels (Single Ended) or 2 Channels (Differential)
M2P.5921-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Programmable DC Electronic Loads
SDL1000X/X-E Series
-
SDL1000X/SDL1000X-E series Programmable DC Electronic Load has a 3.5 inch TFT-LCD display, a user-friendly interface and superb performance specifications. The SDL1020X/SDL1020X-E models feature an input range of 150 V/30 A 200 W while the SDL1030X/SDL1030X-E have an input range of 150 V/30 A 300 W. The SDL1000X series leads with measurement resolution of 0.1 mV/0.1 mA and the base SDL1000X-E series resolution is 1 mV/1 mA and adjustable current rise times from 0.001 A/μs~2.5 A/μs. For remote communication and control, the SDL series includes RS232/USB/LAN interface types. The SDL1000X series delivers stability over a wide range of applications and can meet all kinds of testing requirements. including: Power, battery/handheld device design, industry, LED lighting, automotive electronics, and aerospace.
-
Product
Software Solutions
ZAP MULTIRUN
-
The ZAP MULTIRUN allows parallel or sequential execution of the same script on multiple work stations and mobile devices. Using ZAP MULTIRUN test automation teams expedite time to execution multiplied by number of devices per given test runs.
-
Product
RF One Power Meter
-
The RF One Power Meter is a very versatile instrument covering both analog and digital carriers in an extremely wide frequency range from 30MHz to 6GHz. The RF One is capable of measuring forward and reflected power in the range of a few milliwatts up to 500 Watts. The internal operating system controls measurement, display and the I/Os allowing serial communication to PC, USB to memory stick and USB Serial communication. The I/O options are used to write plots to either memory sticks or to a connected PC, the I/Os can also be used to operate the instrument, giving commands and receiving data. For documentation reference the instrument has a real time clock. Multilayer menus are used to setup and control the operation of parameters. The RF One instrument is small, handy and light weight battery operated with more than 3 hours of continuous operation on the internal NiMh cells. Feature with XML data handling and application viewer is included. Accessory kit with soft carrying bag, car charger and coax adapters for standard types.
-
Product
Impulse Generators
-
HYPERLABS triggerable impulse generators create precise high-speed pulses with 50 to 100 ps rise time. They can be triggered by input from antennas and other signal generator systems.
-
Product
Automatic Transformer Observation System
ATOS
-
Raytech – The World leader in design and manufacturing of high-quality precision measuring instruments and systems, offering flexibility and versatility. Our modular Automatic Transformer Observation System (ATOS) allow you to create a unique and custom solution for any application. ATOS is designed to drastically reduce measuring time and increase test performance, without losing accuracy compared to individual test instruments. With the choice of up to three Multiplexers (primary, secondary, and tertiary), three Winding Resistance Meters, each with three maximum current range options (up to 15A, 50A, or 100A), Turns Ratio, and Integrated power security and safety panel (ISU R), Raytech can create a system with your needs and budget in mind.
-
Product
High Temperature Testing Mobile Conversion Unit
-
Used for applications that require high temperatures (1800C-2000C) for extended periods of time, the High Temperature Mobile Conversion Unit offers enhanced capabilities to accommodate more damanding requirements.The unit is based on the General Purpose MCU which allows for the use of standard specimen grips and accesories.
-
Product
FPGA Boards
-
Take advantage of FPGA cards built on open standards and with a high degree of configurability in order to address a wide range of applications - without the expense and extensive development time of custom in-house developments.
-
Product
Multi-Channel Interface Module
PC104P-MA4
Interface Module
Alta Data Technologies’ PC104P-MA interface module is a multi-channel, multi-protocol 1553 and ARINC PC104-Plus interface card supported by the latest software technologies. The PC104P-MA4 card is based in the industry’s most advanced 32-bit protocol engine, AltaCore, and by a feature rich application programming interface, AltaAPI, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. The hardware and software package provides increased performance and reduces intergration time.
-
Product
Ex-Interface / Multiplexer
PXT0
-
Passive Ex separation interface for Ex-proof connection of transit time sensors
-
Product
PXI 30A Fault Insertion Switch 6-chan 2-bus
40-191-012
Fault Insertion Unit
The 40-191-012 is a PXI fault insertion switch using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
Ground Resistance Testers
-
IP67 protected top in the industry Test all ground types from Class A to Class D with a single meter Wide 0 to 2000 measurement range Minimize cabling time with innovative earthing rods and cable winder
-
Product
8-port LAN Module With Intel® I210-AT Ethernet Controller
AX93326
-
The AX93326 LAN module is built with an Intel® I210-AT GbE Ethernet controller, incorporating Jumbo Frames and Intel® DPDK technologies to optimize the processing of network data traffic. It also provides an optional LAN bypass function to ensure smooth network connectivity at all times, making it an ideal solution for users seeking better protection of their essential business communications in the event of a power outage, system shutdown or crash.
-
Product
PXIe-1062Q, 8-Slot, Quiet, Up to 3 GB/s PXI Chassis
779633-01
Chassis
8-Slot, Quiet, Up to 3 GB/s PXI Chassis—The PXIe‑1062Q is designed for a wide range of test and measurement applications and provides a high-bandwidth backplane. The NI PXIe‑1062Q has four PXI peripheral slots, one PXI Express slot with system timing capabilities, and two PXI Express hybrid slots that accept both PXI and PXI Express peripheral modules.
-
Product
CAN Bus & ARINC-825 (825CAN)
-
The 825CAN module is an intelligent multichannel ARINC 825 (CAN bus) interface module for the multiprotocol Excalibur 4000 & 8000 family of carrier boards. The module supports up to ten ARINC-825 channels. In receive mode, the module stores all or selected messages with status and Time Tag information appended to each message. In transmit mode, the module operates via a transmit Bandwidth Frame which allows scheduling of data transmissions and reduces the need for host computer intervention.
-
Product
Fibre Channel XMC Interface Module
XMC-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
EEE Component Testing and Screening Services
-
DPACI performs 100% screening as well as qualification testing on electronic parts supplied to the high reliability commercial, industrial, space, and U.S. military sectors. We generate software and hardware to test microcircuits, discrete semiconductors, hybrids, PEMS, and other EEE electronic components to exact customer and military specifications. Our engineering experience in electronic parts screening, qualification, and in-house test fixture fabrication allows us to provide value added components in a timely manner.
-
Product
Power Supply Series
NGM200
Power Supply
Thanks to their high accuracy and fast load recovery time, the R&S®NGM200 power supplies are perfect for challenging applications. Their two-quadrant architecture allows them to function both as a source and a sink to simulate batteries and loads. Their short recovery times enable them to handle fast load changes that occur, for example, when mobile communications devices switch from sleep mode to transmit mode. High-speed data acquisition and convenient battery simulation widen the range of applications.
-
Product
Time Node
OSA 5225B
-
The OSA 5225B Time Node is a precise time center featuring two configurable synchronization inputs for redundancy and several outputs. The OSA 5225B can be configured as a secure and redundant NTP Time Server as well as a time distributor of many other time protocols and formats (IRIG-B, PPS, ...).
-
Product
Portable Analyzers
-
The key to the operation of Alpha Moisture Systems' Portable Analysers is the unique Desiccant Dry-Down Chamber. By keeping the sensor dry between tests, the special assembly of the head ensures that the instrument is always ready for immediate use. The head assembly consists of two chambers which have a telescopic action. When the head assembly is in the 'closed' or 'Dry-Down' position, the sensor is completely surrounded by desiccant, which absorbs the remaining water moisture from the sensor and hence it is dry and ready for use. The small space at the bottom of the test chamber enables the sample pipe to be purged before the test commences without wetting the sensor. By placing a finger over the outlet of the head, the sample pressure is able to open the test chamber automatically, exposing the sensor to the gas being tested and enabling accurate reading of moisture content in the sample gas. After each test the head assembly is closed by depressing the inner section so that the sensor will again be dried by the desiccant, leaving the sensor ready for use time and time again. The desiccant is kept in the inner chamber and is not exposed to ambient room air or the sample gas, therefore there is no need for frequent regeneration or replacement of the desiccant.
-
Product
Automatic Software Testing
-
Conformiq offers a next generation solution for automatic software testing. Our products fit the needs of Agile software development by adapting quickly to new product requirements and eliminating the time required for laborious test execution script maintenance during short sprints. Instead of using test cases, Conformiq users have a model, which describes the System Under Test, or the product you want to test.
-
Product
Surface Contamination Monitor
IMI Inspector Alert™ V2
-
The IMI Inspector Alert™ V2 measures alpha, beta, gamma and x-radiation using a 2-inch “pancake” GM detector with high sensitivity to common beta and alpha sources. The easy-to-read digital display shows readings in your choice of µSv/hr, mR/hr, CPM, or CPS. The Total/Timer feature allows timed readings from one minute to 40 hours for precise measurement of low level contamination. An audible alert sounds when the radiation reaches a user-adjustable level.
-
Product
General Purpose Low-side MOSFET Drivers
-
Renesas' family of low-side FET drivers are very high-speed matched dual-drivers capable of delivering peak currents of 2.0 amps into highly capacitive loads and excellent at driving large capacitive loads with minimal delay and switching times. The high-speed performance is achieved by means of a proprietary "Turbo-Driver" circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. These matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10 fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with non-overlapped drive techniques.
-
Product
Microscope
-
An optical instrument used for viewing very small objects, such as mineral samples or animal or plant cells, typically magnified several hundred times.
