Backplanes
An interconnection structure allowing multiple printed circuit boards to coexist using a single bus.
-
Product
PXI Prototyping Module, 1-Slot, 20-Pin GMCT
40-225A-801
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
VME64X 6U 21 Slot with P0
101V64XC21-1621
-
6U VME64x Backplane 21-slot with P0, compliant with ANSI/VITA 1.1-1997, VME extension standard. Includes termination passive inboard, daisy chain automatic active, and power bugs on top and bottom of slots.
-
Product
VME
-
VME remains a strong solution for a wide variety of tech refresh programs. Applications range from command and control systems to high performance signal-processing radar, sonar and intelligence, surveillance, and reconnaissance (ISR) applications. Keeping VME relevant for these applications requires ongoing advancements to achieve processor migration, extending I/O capabilities on the backplane, and supporting higher bandwidth applications.
-
Product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - 3U VPX
Model 5953
-
- Supports Xilinx Zynq UltraScale+ RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2 and 3) interface up to x8- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- Optional VITA-66.4 optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA-46, VITA-48, VITA-66.4, VITA-57.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Model 8257 1-Slot 3U VPX Development Chassis for Quartz Products- Model 4801 Carrier Design Kit for designing custom carrier for the Model 6003 QuartzXM- Model 6003 unique QuartzXM eXpress module enables migration to other form factorsPentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products VideoLive Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boardsPipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoCSynchronize up to eight modules with Model 5903 High-Speed System Synchronization and Distribution Amplifier - 3U VPXPlease refer to the product datasheet for Installed FPGA IP Module details
-
Product
8-Slot 64-Bit 6U CompactPCI Backplane
cBP-6408R
Backplane
- PICMG 2.0 CompactPCI Specification R3.0 Compliant- PICMG 2.1 CompactPCI Hot Swap Specification R2.0 Compliant- PICMG 2.5 H.110 Computer Telephony Specification R1.0 Compliant- Design for 64-bit/33MHz CompactPCI computer system application- One system slot with seven expansion slots, system on right hand side
-
Product
ATCA 5U 14 Slot Mesh w uTCA connector for SHMM
1900001778-0000R
-
The 14-slot mesh backplanes have standard 1X full mesh topologies. Elma Electronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
Product
Extrusion Rail
1404-0016-84
-
VECTOR Electronics and Technology, Inc.
Fits into extrusion rails to attach front panels or backplanes.HP pitch pattern of holes for precise installation offront panels or backplane.
-
Product
Ultra-Performance Motherboard Module
ProDAQ 3180
-
The ProDAQ 3180 ultra-performance motherboard is a register-based VXIbus device supporting single-word transfer and block transfer of 16-bit and 32-bit words. It can be configured for both the A16 and A32 address space. The improved VXIbus interface of the ProDAQ 3180 is compatible to the VXI-1 Rev 4.0 standard and supports the 2eVME and 2eSST protocols, which allow for backplane transfers at data rates of up to 320 MB/s (theoretically). Depending on the slot-0 controller used, the ProDAQ 3180 can sustain data transfers up to 240 MB/s.
-
Product
2U 4 Slot VME64X Mini Crate
VME8004X
-
The Model VME8004X is a 4 slot VME crate, suitable for 6U x 160mm boards, with VME64x compliant backplane. The Unit is powered by 100 – 240 Vac (50 – 60 Hz). The power distribution is 25A@+5V, 10A@+12V, 10A@-12V, 25A @3.3V. The VME8004X provides automatic daisy chain and supports CBLT data cycles.
-
Product
VME 32X 5 Slot 6U
-
ANSI/VITAV 1-1994 VME32 Backplane, 6U 5 Slot Including J1 & J2.Benefits:• Standard VME backplanes are available also in other slot count configurations• Surface Mount Technology – Excellent high frequency performance, high reliability and reduced cost due to SMT
-
Product
ATCA CO14N AC 14 Slot 14U
-
The AdvancedTCA® CO14N 14-slot chassis, AC version suits most of the applications in the field. Its proven cooling and power architecture has been aided by a split backplane technology that allows to upgrade the signal backplane to the latest generation without any effort.
-
Product
VME J1J2 Monolithic 1 slot
101VMEM101-0000
-
VME J1J2 Monolithic backplane 1 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VXS Backplanes
-
VXS (VME Switched Serial) represents an extension of the VME family according to VITA 41.0. This system is downward-compatible, so that assemblies with VME 96-pin connectors can still be used, while adopting the use of serial signals such as Gigabit Ethernet, PCI Express, Serial RapidI/O, and other fabrics.
-
Product
9U Blade Server for 12 Blades with Dual Fabric Switch Slots
cPCIS-3300BLS
Blade Server
- PICMG® 2.16 Packet Switching Backplane architecture- Dual PICMG® 2.16 fabric slots for high availability- 21 slots, including 12 node slots, two fabric slots, three redundant 6U CompactPCI® power modules and one CMM slot- Hot swappable 800 W + 400 W redundant CompactPCI® power supply with universal AC input
-
Product
AdvancedTCA, Type 11A, 4U 19" Horizontal, DC
11A05GJA48Y3HMXX
-
Elma's ATCA, DC, 4U horizontal enclosure with backplane, and shelf mgmt. options. Pluggable and redundant fans, PEMs and shelf managers for availability (99.999%). Optimized via backplane signal integrity studies and chassis thermal simulation.
-
Product
Analog Backplanes
MSXB 030
-
Analog Backplanes provide expansion slots to accommodate compatible analog external boards. Analog Backplanes are passive, and connect all signals in each of the expansion slots in parallel. All expansion slots are identical
-
Product
CompactPCI Chassis 2 Slots
Chassis
Hartmann CompactPCI 1U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model provides a 2 slot 5V I/O 6U cPCI backplane for horizontal mounting of boards. This system is designed with enhanced EMC features.
-
Product
Programmable Multifrequency Clock Synthesizer - 6U VPX
Model 5891
-
- Simultaneous synthesis of up to 10 different clocks- 16 SMC clock outputs- Typical phase noise: -105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 to 100 MHz- Eight programmable VCXOs with 32-bit tuning resolution- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status over the VPX backplane
-
Product
VME64X 7U 16 slot with P0
101V64XM16-0621R
-
7U VME64x Backplane 16-slot with P0, compliant with ANSI/VITA 1.1-1997, VME extension, and VITA 1.7 Increased Current. The extra 1U provides room for extra power bugs or busbars. Includes termination passive inboard and daisy chain automatic active.
-
Product
Five-Site Dual-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier
6567
-
Our Five-Site Dual-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier 32-Bit/66 MHz (6567) adapts five single-wide PMCs to a cPCI slot. At the heart of the carrier is a 6150 PCI-to-PCI bridge that connects the carrier's internal PCI bus to the cPCI backplane.
-
Product
JadeFX FlexorSet 4-Ch. 250 MHz A/D w/DDCs, 2-Ch. 800 MHz D/A w/DUC, Int - 3U VPX
Model 5983-313
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family BrochureVITA-57.4 HSFC FMC+ site offers access to a wide range of possible I/O- Supports Xilinx Kintex UltraScale FPGAs- Four 250 MHz 16-bit A/Ds- Four multiband DDCs- One digital upconverter- Two 800 MHz 16-bit D/As- Extended Interpolation- Sample clock synchronization to an external system referencePCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical interface for backplane gigabit serial interboard communication- LVDS connections to the Kintex UltraScale FPGA for custom I/O and synchronization- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions availablePlease refer to the product datasheet for Installed FPGA IP Module details
-
-
Product
VME J1J2 Monolithic 19 slot
101VMEM119-0500
-
VME J1J2 Monolithic backplane 19 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
Rackmount IPC
-
Industrial Computer Chassis series offer motherboards, backplanes and single board computers, such as IPC chassis, ATX chassis, IPC enclosure for Servers, Server Boards, Server Chassis, and Server Systems. The IPC chassis series build an essential bloc for performance demanding applications.
-
Product
15-Slot 32-Bit 3U I/O with 6U System CompactPCI Backplane
cBP-6515R
Backplane
- PICMG:2.0 R3.0, 2.1 R2.0, 2.7 R1.0- Dimension:202.5 x 262.05 (mm, WxH, vertical insertion view)- Segment:One- cPCI Bus:32-bit/33MHz- System Slot:Right-hand side- System Slot Rear I/O:P3, P4 and P5 rear I/O with AB-type shroud- Peripheral Slot:14 (Bus A: 7 slots, Bus B: 7 *slots)Note- Peripheral Slot Rear I/O:P2 rear I/O with AB-type shroud
-
Product
3U VPX 4 Slot Power & Ground With 3x VITA 67.3C Apertures In P2/J2
101V304P12-9X13
-
The only assigned pins on these backplanes are for 3.3V, 5V and 12V power, and both ground and utility planes are defined. The remaining pins are all user-defined. The rear connectors are all fully populated.
-
Product
cPCI 3U RD
-
Hartmann Electronic’s board design is based on the HIGH-SPEED DESIGN concept. Low reflection is achieved by means of uniform signal surge impedance. The backplane design features an energy buffering feature which works across the entire frequency range.
-
Product
3U CompactPCI 32-Bit 13-Slot Backplane with Rear I/O
cBP-3213PR
Backplane
- PICMG 2.0 CompactPCI Specification Rev. 3.0 compliant- One system slot and twelve peripheral slots via cBP-*R3213 bridge boar- 10-layer PCB for accurate impedance control and electronic noise immunity- Two ATX sockets with DC screw terminals
-
Product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - SOSA Aligned 3U VPX
Model 5553
-
- Supports Xilinx® Zynq® UltraScale+™ RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- 10 GigE Interface- 40 GigE Interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA 49, VITA 46, VITA 48, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Model 8256 3U VPX SOSA Aligned Development Chassis- Model 6003 unique QuartzXM eXpress module enables migration to other form factors- Video: Model 8256 3U VPX SOSA Aligned Development Chassis- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Synchronize up to eight modules with Model 5903 High-Speed System Synchronization and Distribution Amplifier - 3U VPX- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
Power Interface Board 6U, 1 PSU connector with AC pins
106PIBM601-9001R
-
The PIB 6U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
