Backplanes
An interconnection structure allowing multiple printed circuit boards to coexist using a single bus.
-
Product
PC System Electronics
-
Keysight PC electronics provide state of the art laser interferometer performance in the convenient PC backplane format. Axis, servo-axis and compensation boards are available.
-
Product
Gigabit Ethernet Switch
VPX6-688
-
Curtiss-Wright Defense Solutions
The Curtiss-Wright VPX6-688 Gigabit Ethernet switch was designed to provide a complete networking solution for VPX systems. Suitable for a wide range of embedded computing and vehicle network applications, the VPX6-688 provides 24 ports of IEEE 802.3 compliant 1000BASE-T Gigabit Ethernet to the backplane. Optional optical interfaces provide four 1000BASE-SX Gigabit links.
-
Product
Serial Bus Buffers, Extenders, and Accelerators
-
The Analog Devices family of I2C solutions support hot swappable, 2-wire bidirectional bus buffers to allow I/O card insertion into a live backplane without corruption of the data and clock busses. Additional supported 2-wire buses include SMBus, PMBus, the ATCA intelligent platform management bus (IPMB), and the HDMI DDC bus. I2C/SMBus Accelerators improve bus transitions to allows multiple device connections or a longer, more capacitive interconnect, without compromising slew rates or bus performance. ADI's software-programmable and pin-selectable I2C multiplexers help resolve I2C address limitations, increase fan-in or fan-out, and integrate bus buffers and rise time accelerators for an all-in-one solution. Resistor configurable I2C address translators can be configured with over 100 unique slave addresses to allow multiple slave devices with the same address to coexist on the same bus.
-
Product
PCI Express, PCI, Multi-Interface Test Backplanes
-
Amfeltec PCI Express, PCI, Multi-Interface Test Backplanes
-
Product
Rack Mount Osprey Chassis 5.25" Qbus
97106-Q
-
5.25" high by 19" wide by 20" deep (134 x 483 x 508 mm), this chassis is FCC/CE certifiable**. A quad-height Qbus backplane, cooling fans, and slides are provided, diskette and hard drives (two visible 5.25" and two hidden 3.5" bays), and up to four quad-height Qbus compatible cards.
-
Product
VXS 21 Slot
-
The Comtel VXS Backplane 21 slots match performance and cost-effectiveness by realising a fully optimised signal and power distribution environment. Design techniques ensure uniform impedance controlled signaling environment and ground guarding minimises line-to-line crosstalkThe VXS provides the high-speed switched serial performance of VITA 41, hybrid design includes VXS payload slots, VXS switch slots and conventional VME64x slots, The 21 slot VXS backplanes supports data rates well beyond 3.125Gb/s per link. As a dual-star design, it can be operated with two switch boards, allowing addressing of both link ports on payload cards.
-
Product
OpenVPX Cable Solutions
OPENVPX-CABLE
-
Compliant to VITA 46 and 65, the cabling assemblies are ideal for development. They can be used for I/O to bulkhead connectors and slot-to-slot connections. Front-plug versions allow testing across the backplane or full interconnect path.
-
Product
Open Test Platform for High Performance Automotive Applications
TSVP
Test Platform
The R&S®TSVP family of products is an open test platform from Rohde & Schwarz ideal for high performance automated test equipment (ATE) applications. The chassis contains a mechanical frame, digital backplane, analog backplane, mains switching and filtering, power supply and diagnostic extensions. A highlight is the analog bus for routing measurement signals between different slots without additional external wiring.
-
Product
3U VPX Development Kit
Software Development Kit
This development kit enables efficient 3U VPX backplane design and software verification.- 3U VPX architecture- One CPU blade, one GPU blade (optional), SOSA-aligned- 1TB NVMe pre-installed in CPU blade- Rear transition module(s) included- Test Frame with backplane pre-installed
-
Product
Pulse Pattern Generator, 3.35 GHz, dual-channel
81134A
Pulse Generator
When timing and performance requirements are critical, for example in high-speed serial bus applications like PCI Express or Serial ATA, its fast rise times and low intrinsic jitter allow the precise and in-depth characterization of devices, e.g. receivers or backplanes. On top of that, it allows to generate application-specific signal levels like pre- and de-emphasis (PCI Express) or squelch (Serial ATA). The Keysight 81134A lets you test your DUT instead of the pulse or data source!
-
Product
VME64X 7U 8 slot no P0
101V64XM08-0620R
-
7U VME64x Backplane 8-slot w/o P0, compliant with ANSI/VITA 1.1-1997, VME extension, and VITA 1.7 Increased Current. The extra 1U provides room for extra power bugs or busbars. Includes termination passive inboard and daisy chain automatic active.
-
Product
VPX, Type 12V, 19" Rackmount Family
12V-VPX
-
Elma's Type 12V, high performance VPX chassis platform, fully compliant to VITA 46 & 65 standards. Consisting of alodined aluminum enclosures, VPX backplane, power supply, cooling system and AC/DC power components.
-
Product
3U / 6U PXIe Chassis
Chassis
The GX7100e Series are 14-slot combination PXIe chassis that accommodate a 3U PXIe embedded controller or a MXI express controller as well as 3U & 6U PXI / PXIe insruments in 4U of rack space. The GX7100e’s unique format includes seven 6U slots and seven 3U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI / PXIe applications and requirements. The backplane architecture supports Gen 2, 4x4 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7100e offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
Product
PCIe X8 And X1 Bridge Card
-
The Guzik PCI Express Host Interface Bridge Card was designed to expand the x8 PCI Express Gen 2 (PCIe) slot in a host PC to an AXIe or a Guzik GSA 6000 chassis via a x8 PCI Express Gen 2 and a x1 PCI Express Gen 1 high speed PCI-SIG specified data cables. This allows the end node to connect to the host bus at speeds up to 3.2GByte/sec user data rate. The Bridge Card installs in a x8 or x16 slot of a PCIe backplane or a PCIe motherboard, provides additional board-based retention and reinforced front panel.
-
Product
Backplane Test System
402HV
-
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
Product
Power Interface Board 3 HE, 1PSU-Steckverbinder mit AC-Pins
106PIBM301-9001R
-
The PIB 3U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
LXI High Voltage Matrix - 400V 50x4 Matrix Plugin Module
65-218-101
Matrix Switch Module
The 65-218-101 plug-in module is part of a scalable high voltage matrix platform designed to provide a large matrix solution with a switching capacity of 400V. This version of plug-in includes access to the chassis backplane.
-
Product
VME64X 7U 15 slot no P0
101V64XM15-0620R
-
7U VME64x Backplane 15-slot w/o P0, compliant with ANSI/VITA 1.1-1997, VME extension, and VITA 1.7 Increased Current. The extra 1U provides room for extra power bugs or busbars. Includes termination passive inboard and daisy chain automatic active.
-
Product
VME Backplane
VME J1
-
VECTOR Electronics and Technology, Inc.
Vector offers wide range of VME backplanes from 3 to 21 slots wide in J1 and J2 are 3U backplanes. All VME backplane boards are constructed from FR4 epoxy glass material and are assembled and tested. Press fit connectors are used throughout on all sizes.
-
Product
VXS Backplanes
-
VXS (VME Switched Serial) represents an extension of the VME family according to VITA 41.0. This system is downward-compatible, so that assemblies with VME 96-pin connectors can still be used, while adopting the use of serial signals such as Gigabit Ethernet, PCI Express, Serial RapidI/O, and other fabrics.
-
Product
VPX / Open VPX Backplanes
-
VPX is a broadly defined technology utilizing the latest in a variety of switch fabric technologies in 3U and 6U format blades. Open VPX is the architecture framework that defines system level VPX interoperability for multi-vendor, multi-module, integrated system environments.
-
Product
14-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB118
-
The FAB118 offers one PCIe x16 slot, five PCIe x4 slots and six 32bit/33MHz PCI slots as well as the PICMG 1.3 slot for the SHB (system host board). The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB118 is designed for the 14-slot industrial chassis, such as Axiomtek's AX61460, AX6145, AX61400, AX6156E/LE/LLE, and AX61491.
-
Product
ATCA 5U 2 Slot Mesh w uTCA connector for SHMM
109ATCA502-9020R
-
The 5U 2-slot ATCA backplane is a switchless 2X Replicated Mesh with point-to-point links between the slots. However, a 1X Mesh can also be implemented on the 2-slot.
-
Product
ATCA 5U 5 Slot Mesh w uTCA connector for SHMM
109ATCA505-9020R
-
The 5U 5-slot ATCA backplane is a 3X Replicated Mesh. However, Dual Star, 1X and 2X Meshes can all be implemented across the 5-slot backplane.
-
Product
PCI To CPCI Or PXI Extender Board
MS 1720
-
PCI to CPCI Extender card is used for extending the standard desktop PCI bus to compatible CPCI bus. This will help to test all the CPCI and PXI cards without having a CPCI or PXI backplane. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the CPCI and PXI boards.
-
Product
PXI Prototyping Module, 1-Slot, 9-Pin D-Type
40-225A-701
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
VME J2 21 slot
101VMEJ221-0900
-
VME J2 backplane 21 slot, compliant with ANSI/VITA 1-1994. The A+C rows are bussed in all slots. Also, row B has onboard, inboard termination.
-
Product
3U 12-slot VPX Backplane Aligned To SOSA 1.0
1OVX312AFQ-xxxx
-
3U 12-slot backplane with profiles aligned SOSA. It is designed to meet the U.S. Army’s C5ISR Modular Open Suite of Standards (CMOSS), and supports high-speed signals on all data paths and VITA 67.3 and VITA 66.5 connectors.
-
Product
VME J1J2 Monolithic 2 slot
101VMEM102-0500R
-
VME J1J2 Monolithic backplane 2 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
PXIe-1071, 4-Slot, Up to 3 GB/s PXI Chassis
781368-01
Chassis
PXIe, 4-Slot, Up to 3 GB/s PXI Chassis—The PXIe‑1071 is designed for a wide range of test and measurement applications and provides a high-bandwidth backplane. Its compact and lightweight form factor is ideal for minimizing the footprint of your installation, making it ideal for desktop or portable use cases. The PXIe‑1071 accepts PXI Express modules or standard PXI hybrid-compatible modules in every peripheral slot.
