Power Sensors
-
Product
REM-11100, 2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O
784748-01
Voltage Input Module
2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O - The REM‑11100 is a voltage input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11100 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. This module features 2‑, 3‑, and 4‑wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling.
-
Product
Power Cell Power Transducers for Wide Ranging AC/DC Loads
PH-3A and PH-1000
-
You can know the load on an electric motor by measuring the electric current going to the motor (Amps). But, this is not the best way to do it since a lightly-loaded motor doesn't use the electricity very efficiently. (In technical terms, the power factor is low.)A better way to know the load is to measure the motor power. (Power is measured in Horsepower or Watts.) Motor power gives you a straight line so it works well even when the motor is lightly loaded.The Power Sensors that we make measure the motor load (Horsepower or Watts) and send a signal to meters or computers. The operator can see what the status is on the meter or, the computer can make decisions.
-
Product
50 MHz to 18 GHz USB Peak and Average Power Sensor
U2021XA
Power Sensor
The U2020 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming.
-
Product
Software-controlled Generator
IPTN16
-
*The module provides output of constant stabilized voltage through 16 independent channels in 2 ranges ± 2 V and ± 10 V with a step of 5 mV, as well as a stabilized current of ± 10 mA with a step of 5 μA.The IPTN16 module is intended for use in information measuring VXI systems and can be used to power resistive temperature sensors or strain gauges with voltage or current with an accurate and stable value.*The IPTN16 module can also be used to simulate voltage or current sensors when checking measuring instruments and channels of measuring systems.
-
Product
Fiber Photodiode Power Sensors
-
These interfaces provide communication between an attached sensor and a PC or other external control unit. They are designed to be controlled via an external device or operated autonomously using the analog output; there are no controls or display screens.
-
Product
sbRIO-9218, Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module
783362-02
Analog Input Module
Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module - The sbRIO‑9218 helps you perform multipurpose testing. With the sbRIO‑9218, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors. You also can use the sbRIO‑9218 to perform quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. You can individually select and perform a different measurement type on each channel. Additionally, the sbRIO‑9218 features 60 VDC analog input isolation. Non-enclosed modules are designed for OEM applications.
-
Product
NI-9218, 51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module
783367-01
Analog Input Module
51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module - The NI‑9218 is designed for multipurpose measurements. It offers built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. Each channel is individually selectable, so you can perform different measurements on each channel. The NI‑9218 is ideal for creating universal test systems for automotive, off-highway, and data-logging systems.
-
Product
DC/10 MHz – 18 GHz USB Thermocouple Power Sensor
U8481A
Power Sensor
The U8480 series is the fastest USB thermocouple sensor in the world without compromising the best in class linearity of the legacy 8480/N8480 series thermocouple sensors, all in a compact USB based form factor
-
Product
Diode Power Sensor
8487D
Power Sensor
Excellent SWR for reducing mismatch uncertainty Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 50 MHz to 50 GHzDiode power sensing element
-
Product
USB Power Sensor, 50 MHz to 24 GHz
U2002H
Power Sensor
Measure average power over the frequency range 50 MHz to 24 GHz and power range -50 dBm to +30 dBm.
-
Product
Diode Power Sensor
8481D
Power Sensor
The 8481D diode power sensor measures average power over the frequency range 10 MHz to 18 GHz and power range -70 to -20 dBm (50 dB dynamic range).
-
Product
RF Power Sensors
-
Providing the highest video bandwidth and fastest rise times, RTP5000 peak power sensors with Boonton’s Real-Time Power ProcessingTM deliver 100,000 measurements per second, no gaps in signal acquisition and zero measurement latency.
-
Product
10 MHz To 50/53 GHz LAN Wide Dynamic Range Average Power Sensor
L2055XA
Power Sensor
The Keysight L2055XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz LAN average power sensor.
-
Product
Pulse
-
*MODBUS Master RS485 / RS232*Up to 10 slaves or 15 registers per slave*Monitoring and supply of power to the sensor*Local and remote configuration
-
Product
Saluki S87234 Series USB Peak and Average Power Sensor (max. 67GHz)
-
S87234D/E/F/L USB peak and average power sensor is a diode-detection broadband power measurement instrument based on the USB 2.0 interface, which can realize accurate average power measurement, pulse power measurement with large dynamic range and CCDF statistical measurement analysis. The frequency range covers 50MHz to 67GHz, the highest power accuracy can reach 0.2dB, the video bandwidth is ≥30MHz, and the rise/fall time is ≤13ns.S87234 series can flexibly expand the power measurement function of electronic measuring instruments and test systems, and is mainly used for field testing, production line testing and system integration.
-
Product
Garmin LIDAR-Lite V4 LED
Distance Measurement Sensor (Qwiic)
-
The LIDAR-Lite v4 Qwiic from GARMIN is a high-performance, wireless optical distance measurement sensor that doesn't require any soldering to get started. This is the ideal solution for drone, robot, IoT, or unmanned vehicle operations when space is tight and power is limited. This sensor has up to a 10 meter range, 1cm resolution, and requires 85mA during data acquisition. The user can read and write to the LIDAR-Lite v4 using the I2C protocol; this is where the addition of the SparkFun Qwiic system really shines. The LIDAR sensor requires 5V to operate but runs on 3V3 logic. With a 5V boost circuit and an easy-to-use Qwiic connector you can power the sensor and get distance measurements over Qwiic all with a single piece of hardware.
-
Product
USB Power Sensor Module For Measuring Receiver
U5532C
Power Sensor
The U5532C USB power sensor module is specially design for the N5531X measuring receiver. Based on the Keysight USB power sensor and a power splitter, the U5532C provides the N5531X measuring receiver user with a single RF input device covering up to 50 GHz. Using of the U5532C USB power sensor module eliminates the requirement of an external power meter, simplifying the setup process and saving lab space. The measurement integrity and accuracy are guaranteed by the fully defined specification sets. The traceability of measurement uncertainties is also ensured.
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 18 GHz
N9937A
Spectrum Analyzer
100 kHz to 18 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 6.6 lb. (3.0 kg)
-
Product
USB Power Sensor - 100 MHz to 20 GHz, Average, Peak (Pulse), Pulse Profile
GT-8555B
-
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
Product
DC/10 MHz – 33 GHz USB Thermocouple Power Sensor
U8485A
Power Sensor
The U8480 series is the fastest USB thermocouple sensor in the world without compromising the best in class linearity of the legacy 8480/N8480 series thermocouple sensors, all in a compact USB based form factor.
-
Product
RF Power Sensor Solutions
-
Bird provides innovative power sensor solutions for all types of RF applications. From simple directional power sensors for the measurement of transmitter output power and VSWR measurement and monitoring applications, to highly accurate self correcting power sensors for process control applications, you can rely on Bird sensor products to meet the needs of your unique applications.
-
Product
SmartWireless Gas Detector
CXT
-
Teledyne Gas & Flame Detection
All component parts are rated for Class 1; Division 1, Group C, D hazardous areas. These advanced field devices consist of a CXT low power gas detection sensor and wireless transceiver packaged in a single enclosure. Power is provided by a disposable “C” cell battery pack capable of continuous operation for greater than 60 days. Additional power options include a Smart Rechargeble battery with a run time of 5-6 months, a disposable “D” cell battery pack with a run time of 9 months and solar panel providing continuous operation.
-
Product
Battery Module
BAT-200
-
The Battery module supplies power to a sensor, or chain ofsensors, operating in the Off-Line mode, and to sensors connectedto an RF communication module.The Battery module can be recharged by connecting it to the PC'sUSB socket via the USB module's USB cable.
-
Product
FieldFox Handheld Microwave Vector Network Analyzer
N9925A
Vector Network Analyzer
9 GHz max frequency Carry the world's most integrated handheld T/R VNA analyzer Expand your measurement flexibility with optional 2-port VNA, time-domain, vector voltmeter, cable and antenna analyzer and more Save time by simultaneously measuring all four S-parameters with a single connection Perform accurate testing with QuickCal, full 2-port unknown thru Cal, TRL Easily measure average and pulse power with a USB power sensor
-
Product
Power Sensors
8480 Series
-
The 8480 thermocouple and diode power sensors series provide extraordinary accuracy, stability, and SWR over a wide range of frequencies and power levels.50 dB dynamic range (maximum) over –70 to +44 dBmFrequency range from 100 kHz to 110 GHz (sensor dependent)Accurate average power measurementsRange of thermocouple and diode power sensorsCompatible with EPM, EPM-P, P-series, and E1416A power meters
-
Product
10 MHz To 54 GHz LAN Wide Dynamic Range Average Power Sensor
L2056XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Low Power Wireless Gas Detector
CX
-
Teledyne Gas & Flame Detection
Model CX sensors are equipped with standard analog 4-20mA, and Modbus™ RTU RS-485 outputs and can be used with SmartWireless Site Sentinel CX/CXT controllers. The CX is a very low power device making it an ideal choice for a battery powered detector (optional) in applications where power is unavailable or not economically feasible.CX gas detection sensors are easily and economically deployable in both permanent and temporary installations. These low power sensor assemblies utilize electrochemical technology for a long list of toxic gases.
-
Product
EPM and EPM-P Series Power Meter
-
The EPM and EPM-P Series provides high-performance, programmable power meters for CW, average and peak power measurements. EPM Series: measure average power over a range -70 dBm to +44 dBm, and over frequency range 9 kHz to 110 GHzEPM-P Series: measure peak, average and time-gated power over -65 dBm to +20 dBm, to 18 GHz using E932XA power sensors. It provides complete pulse and statistical analysis with PC software via the GPIB or RS232
-
Product
Saluki S8723X Series USB CW Power Sensor (9kHz - 40GHz)
-
S8723X series is a diode detector USB power sensor based on a USB 2.0 full-speed/high-speed adaptive interface. It has a wide frequency range and large power dynamic range. It can be connected to a computer or other electronic measuring instruments, easy to set up a power test system, particularly useful for field and other low-cost production line testing and power testing.
-
Product
Peak And Average Power Sensor, 50 MHz - 6 GHz, 5MHz Bandwidth
E9323A
Power Sensor
The E9323A power sensor has a 5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on W-CDMA wireless formats such as cdma2000.
