Module Carriers
Carrier Modules are highly-integrated small footprint board-to-board connectible packages.
-
Product
PXI/PXIe High Voltage Multiplexer, Quad 5-Channel, 1-Pole
40-321-101-HI
Multiplexer Module
The 40-321-101-HI (PXI) and 42-321-101-HI (PXIe) are quad 5-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 2.5 GHz, 75 Ω, 1.6/5.6, Failsafe
42-785C-752
Multiplexer Module
The 40-785C-752 (PXI) and 42-785C-752 (PXIe) are dual failsafe SP6T 2.5 GHz unterminated 75 Ω microwave multiplexers. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
Keysight 40/80 Channel Optically Isolated FET Multiplexer for 34980A
34925A
Multiplexer Module
The Keysight 34925A module for the 34980A Multifunction Switch/Measure Unit is a high speed multiplexer that uses long-life, solid-state relays. The high-speed FET relays scan up to 1000 channels-per-second. Use this module for high-volume automated test applications that need high-speed, long-life relays.
-
Product
Dsub25 To 5 SMB Adapter
PX0106A
Adapter Module
Keysight's PX0106A Adapter converts Dsub25 outputs to five SMB outputs with path through connection. It supports the Keysight M9614/15A.
-
Product
PXI Power Multiplexer, 16-Channel, 2 Pole
40-650A-002
Multiplexer Module
The 40-650A-002 is a PXI 16 Channel Power Multiplexer, suitable for switching inductive/ capacitive loads up to 5A at 250VAC.
-
Product
PXI Prototyping Module, 2-Slot, 96-Pin Micro-D
40-225A-102
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI High Voltage Multiplexer, 24-Channel
40-320A-101
Multiplexer Module
The 40-320A-101 is a single 24-channel MUX and is part of our 40-310/320A range of High Voltage Switching Modules which will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320A) configurations.
-
Product
PXI Solid State Multiplexer Module, Dual 3-Channel, 10 A
40-666B-011
Multiplexer Module
The 40-666B-011 is a dual 3-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
LXI Single 32 Channel Fiber Multiplexer SC, Multi-Mode
60-851-214
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI Quad 4 to 1 RF Multiplexer 3GHz 50 Ohm MCX
40-872-104
Multiplexer Module
The 40-872-104 is a 50 Ohm 4 to 1 RF MUX with 4 banks in a single PXI slot. It exhibits low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-222
Multiplexer Module
The 40/42-860A-222 is a PXI/PXIe dual insert/bypass switch with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP10T, 8 GHz, 50 Ω, N-Type, Remote Mount, Failsafe
42-788-112-E
Multiplexer Module
The 40-788-112-E (PXI) and 42-788-112-E (PXIe) are dual failsafe SP10T 8 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
PXIe Microwave Multiplexer, Single SP4T, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-785C-431-E
Multiplexer Module
The 40-785C-431-E (PXI) and 42-785C-431-E (PXIe) are single failsafe SP4T 26.5 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 50 GHz, 50 Ω, SMA-2.4, Terminated, Remote Mount, Failsafe
42-785C-451-TE
Multiplexer Module
The 40-785C-451-TE (PXI) and 42-785C-451-TE (PXIe) are single failsafe SP4T 50 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
20 Channel Multiplexer (2/4-wire) Module for DAQ970A and DAQ973A
DAQM901A
Multiplexer Module
20 Channel Multiplexer (2/4-wire) Module. High voltage switching capability of up to 300 V and built-in thermocouple reference junction.
-
Product
PXI Solid State Switch Module, 6xSPST, 30 A
40-183B-011
Switch Module
The 40-183B-011 has 6 high current SPST switches in two PXI chassis slots. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 30A of continuous current and switch up to 40V signals. The switch can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
4/8-port Asynchronous Serial Communications Modules
cPCI-3534/3538-S
Communications Module
- 32-bit CompactPCI, PICMG 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- 4/8 asynchronized communications ports with intelligent buffer- Three RS-232 ports and one isolated RS-422/RS-485 port with 2500 VRMS isolation voltage for cPCI-3534, and eight RS-232 ports for cPCI-3538- Surge protector in TXD/RXD signal line
-
Product
16GB SO-DDR5-5600 2GX8 1.1V SAM
AQD-SD5V16GN56-SB
Memory Module
SAM Original Chip, PCB: 30μ gold finger, Anti-sulfuration, On-die ECC for Enhanced RAS, Operating Temperature: 0°C ~ 85°C.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, SC/PC Connectors, With Interlock
42-850A-214-HI
Multiplexer Module
The 40/42-850A-214-HI is a PXI/PXIe 4-channel multiplexer with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Circuit Module, Riser for ISMB, PCIex4 to 3PCIex1 A101-3, RoHS
AIMB-R4301-03A2E
Circuit Module
- Connecting Interface: PCIe x4- Expansion Slots: 3 PCIex1
-
Product
PXI 3A Power MUX BRIC, 16-Channel, 12-Pole
40-571-304
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 9-Bank 18GHz SMA
60-801-209
Multiplexer Module
The 60-801-209 is a 6-channel, 9-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI-2545, 2.7 GHz, 50 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module
778572-45
Multiplexer Module
2.7 GHz, 50 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module—The PXI‑2545 is an RF signal multiplexer switch module. The internal termination of the PXI‑2545, which helps prevent high-power reflections that arise from open channels on the module, makes it ideal for use in RF applications where such reflections can damage the source. The module also provides excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
PICMG 2.11 47-Pin Hot-Swap Redundant 3U CompactPCI 8HP 250 W Power Module
cPS-H325/AC
Power Module
- PICMG® 2.11 CompactPCI® Power Interface compliant- 3U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 250 W DC output
-
Product
1x8 Multiplexer Plug-In
1260-138A
Multiplexer Module
The Astronics1260-138A is an eight 1x8, two-wire scanner/multiplexer plug-in card for the Adapt-a-Switch® platform. It installs, easily and directly from the front panel, into the Adapt-a-Switch VXI Carrier, 1260-100.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 40GHz, 50Ω, SMA-2.9, Remote Mount
40-784B-143-E
Multiplexer Module
The 40-784B-143-E (PXI) and 42-784B-143-E (PXIe) are triple SP4T 40GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
Signal, Module, Receiver, CASS, 210 Position, J4, Right Angle PCB Mount
510113133
Receiver Module
Signal, Module, Receiver, CASS, 210 Position, J4, Right Angle PCB Mount.
-
Product
PXI 2A Multiplexer, 2-Bank, 64-Channel 1-Pole
40-614-010
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
COM Express Basic Size Type 6 Module with 11th Gen Intel® Core™, Intel® Xeon® and Intel® Celeron® Processors
Express-TL
Computer on Module
ADLINK’s Express-TL COM Express Type 6 Basic size module is based on the 11th Gen Intel® Core™, Xeon® W and Celeron® 6000 processor, and is the first COM Express module to support PCI Express x16 Gen4, effectively doubling the bandwidth of previous generation COM Express modules. With a combined 8 cores, 16 threads, and up to 128GB memory, the Express-TL brings uncompromised system performance and responsiveness to your solution. Featuring brand new Gen 12 Intel® UHD Graphics and Intel® AVX-512 Vector Neural Network Instructions (VNNI), the Express-TL provides AI inferencing performance as much as 3X higher compared to previous generation non-VNNI platforms. The integrated Gen 12 Intel® UHD Graphics core can be configured to support one 8K independent display or four 4K independent displays (HDMI/DP/eDP). In addition, legacy display interfaces such as LVDS and analog VGA are still supported as build options. Key features for today’s applications are support for 2.5 GbE and USB 3.2 with transfer rates of up to 10Gb/s that can transfer image data from cameras faster than previous generation products. Combined with 8 processor cores at 25W TDP, Intel® AVX-512 VNNI, Intel® OpenVINO™ toolkit and Intel® UHD Graphics, the Express-TL is well suited for AI at the edge applications (AIoT/IoT).
-
Product
PXI High Density Multiplexer, 8-Bank, 8-Channel, 1-Pole
40-610A-009
Multiplexer Module
The 40-610A-009 is a 8-bank, 8-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
