VME Carriers
-
Product
ARINC-429/717 XMC Interface For SBCs, VPX, VME, CPCI/PXI Systems
XMC-A429
Interface Card
The card design is based on the industry’s most advanced 32-bit ARINC FPGA protocol engine, AltaCore™, and a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET, LabVIEW, RTOS) architecture. This hardware and software package provides increased system performance and flexibility while reducing integration time.
-
Product
6U VME 1/10/40 GbE Switch
ComEth4070e
-
The ComEth 4070e is a cutting-edge 6U Layer 2/3 Ethernet switch for VME64x systems. Powered by the newest Marvell highly integrated system-on-chip (SoC) with programmable packet processors.
-
Product
8-Channel VME 32 MHz Arbitrary Waveform Generator
V344
-
The V344 provides eight independent digitally synthesized waveform outputs, each programmable for frequency, amplitude, and phase.
-
Product
Quad IP Carrier Module With Front I/O
DP-cPCI-5202
-
DP-cPCI-5202 IP carrier board provides electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.
-
Product
16-Channel VME RTD/Resistance Input Module
V410
-
The V410 is a 6U VME module that provides sixteen independent analog inputs that may be used to read RTDs, thermistors, and other similar resistive sensors. It can also read cryogenic diodes. Users may set input range and adjust other settings at VMEbus speed, and depending on the range selected the microprocessor will do the necessary calculations and output voltage, resistance, or temperature. Temperature conversion is available for 100Ω and 1000Ω, series 385 and 392, platinum RTDs.
-
Product
XMC Module Carrier PCI Express x 8
SK4-WALTZ
-
SK4-WALTZ is a bidirectional 8-lane PCI Express® Gen3 redriver, for optimum high speed signal integrity, and should be installed into a fat pipe peripheral slot of a CompactPCI® Serial backplane.
-
Product
300-Watt AC/DC Power Supply, 6U VME
Model 56SQ2
Programmable Power Supply
NAI’s 56SQ2 is a 300 Watt AC/DC Power Supply that uses two slots in a standard VME chassis. It is conduction-cooled through the card edge/wedgelock. This power supply accepts either a single- or three-phase input and provides up to 5 standard VME outputs plus standby at 300 Watts. It is designed for VME and general purpose applications. An onboard microcontroller allows for design flexibility.Standard features include continuous Background Built-in-Test (BIT); remote error sensing; holdup time; and protection against transients, overvoltage and short circuits. Options such as power fail warning, vibration testing, over-temperature monitoring and shutdown, current share, and extensive signaling (including ANSI/VITA) are available.
-
Product
PCI Express FMC Carriers
-
Sundance Multiprocessor Technology Ltd.
FMC carrier boards based on the PCI express format:
-
Product
Carrier Boards
ROM-DB7502
Carrier Board
ROM-DB7502 is the Referenced Carrier Board designed for Advantech's Qseven 2.0/2.1 module. It i provides a thorough environment for module board evaluation with its completefunction support. It also supports 12V power input through AC/DC power adapter and with smart battery design, it's more easier for the end user to design portable devices by referring ROM-DB7502 design.
-
Product
VME Test Extender 6U/220mm Universal
110EXT6122-000X
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
6U VME Single Board Computers
-
NAI's modular 6U VME single board computers can be configured with up to six NAI intelligent I/O and communication function modules. Choose from more than 40 intelligent I/O, communication, and Ethernet switch functions for the highest packaging density and greatest flexibility of any SBC board in the industry. NAI will integrate your choice of SBC and I/O functions to quickly meet your rugged system requirements. These SBCs are specifically designed for rugged defense, industrial, and commercial applications.
-
Product
Dual PMC Carrier for 6U CompactPCI
TCP262
-
The TCP262 supports standard PMC front I/O and CompactPCI rear I/O fully compatible to the TCP260. The PMC slot 2 (upper PMC) I/O lines are connected directly to the CompactPCI connector J5. The PMC slot 1 (lower PMC) I/O lines are connected directly to the CompactPCI connector J3.
-
Product
VME Bus Repeater
VME-5532L
-
Easily link your VMEbus systems via fiber-optic cable, with total electrical isolation, no EMI generation and high-noise immunity.
-
Product
16-Channel VME Analog Output/Thermocouple Simulator Module
V470
-
The V470 is a 6U VME module that provides sixteen independent, isolated analog outputs that may be user-programmed to operate as voltage outputs or thermocouple simulators. Users may write temperature or voltage values at VMEbus speed, and the microprocessor will transparently do all necessary calculations and update the channel electronics.
-
Product
VME Test Extender 9U/400mm J1/J2/J0
111EXT9140-0120
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
PCI Express to VME interface
SIS1100e/3104
-
Single width 6U VME master/system controllerred ball, 1/2/4 GBit/s optical link, red ball, up to 450 m link distance, red ball 128 MBytes memory (PPC Ethernet or VME slave)
-
Product
3U And 6U CPCI CARRIER Board
MS 1715
-
*Bus Interface:- 32 Bit/64 bit PCI Bus with cPCI Interface*Two slots of 32/64 bit PMC connector interface*Speed of operation up to 66MHz*64 bit, 66MHz PCI Bridge based design*Self Test future
-
Product
PCI Generic Carrier Cardfor PMC (PCIbus Mezzanine Card) Modules
ACP-1
-
PCI generic carrier card for PMC (PCIbus mezzanine card) with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
Product
PMC Carrier for 3U CompactPCI
TCP270
-
The TCP270 is a standard 3U CompactPCI carrier that provides front I/O and rear I/O for a single width PMC module. This PMC to 3U CompactPCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in CompactPCI systems.
-
Product
VME / VME64x Load Board 6U
1940000140-0000
-
The Elma Electronic VME / VME64x load board provides a means to test the power generated by and cooling capability of VME systems. This makes it easier to locate hot spots in the chassis, so the airflow can be properly directed.
-
Product
VME Module
ICC-8-xxx
-
The ICC-8-xxx is the second generation of the ICC-8 board. Enhancements includes true RS-485 communications with jumper configurable I/O by the user. The ICC-8-xxx is a VME based, 8 channel intelligent and versatile solution to serial data communications designs.
-
Product
SATA Drive Carrier
SD1-DISCO
-
The SD1-DISCO is a peripheral slot card for CompactPCI® Serial systems. The board accommodates a 2.5-inch size SATA drive, controlled by the SATA channel derived from the backplane connector P1.
-
Product
Adapter / Carrier Converter Card
PCIBPC104pET
-
PCIBPC104pET adapter / carrier converter card provides the ability to install 1-4 active PC104p or PCI-104 cards into a standard PCI slot. PCIBPC104pET has a PC104p and PCI-104 compatible stack position mounted to a universal voltage shorter than 1/2 length PCI card. The PC104p position is stackable with all 4 active positions usable.
-
Product
VME Power Supply
-
VME is a high speed and high performance bus system with powerful interrupt management and multiprocessor capability. It was created by combining VERSA-bus electrical specifications (1979) with the Euro card format resulting in the VME-bus Revision A - 1981 specification. The VME-bus specification has since then been refined through revisions B (1982), C, C.1, IEC 821 & IEC297 and IEEE 1014-1987. VME represents one of today's most used industry bus .
-
Product
Multi Functional VME Logic Module
MDGG-16
-
The MDGG-16 is a single wide 6U VME multi functional FPGA based delay logic and timing module which provides often needed functions as gate generator & pulse generator, logic fan in - fan out, coincidence register and scaler / pre-scaler. The module has 16 LVDS/ECL inputs and 16 ECL outputs on pin headers and 2 NIM inputs as well as 4 NIM outputs (Lemo), which are free configurable in regards to their functionality.
-
Product
3U CPCI Dual IP Carrier
CPCI-SIP
-
The CPCI-SIP module provides a 3U high performance flexible I/O scheme that supports industry standard Industry. PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-SIP is the perfect solution. The CPCI-SIP is also available with the Industry Pack lines routed to the CompactPCI P2 connector for application that require rear panel I/O.
-
Product
48-Channel VME Isolated Digital Input Module
V280
-
The V280 is a single-wide, 6U VME module that includes 48 isolated logic inputs. It is available in versions for nominal 5 volt or 24 volt input levels. The V280 has independently programmable rising and falling edge response times to support contact debounce, glitch catching, and DC or AC inputs.
-
Product
IC-PPC-VMEb, 6U VME Single Board Computer
IC-PPC-VMEb
-
The IC-PPC-VMEb is a QorIQ T2081 based 6U VME Single Board Computer with embedded L2 switch and user-programmable FPGA. SWaP-optimized, with more computing power and backward compatibility with existing designs and flexible interface combinations.
-
Product
Carrier Demodulator with LED Display
CD23/223
-
The CD23 and CD223 Digital Transducer Indicators are designed for use with variable reluctance and differential transformer transducers. The CD23 accepts input from a single transducer, and the CD223 accepts two switch-selectable inputs, with Zero and Span controls for each input. The indicators provide 5 Vrms, 5 kHz carrier excitation voltage to the transducer(s) and solid state circuitry to amplify, demodulate and filter the transducer output signals. A 3 1/2 digit front panel display is standard, with a 4 1/2 digit display optionally available.
-
Product
VME Master - DAQ and Detector Interface
VX1394
-
The VX1394 board features a radiation hard 4.8 Gbps SERDES ASIC, which, in connection to a rad-hard optical transceiver implements a newer generation optical links for many detector readout systems. The ASIC performs data transmission, trigger distribution and clock forwarding towards the front-end electronics in the crate.
