VME Carriers
-
Product
PMC Carrier Module
DP-VME-5114
-
DP-VME-5114 is a VME-Based PMC Carrier Module. This 6U VME board PMC carrier can accommodate two PMCs. This board can be used for data acquisition, automated testing and checkout systems
-
Product
Carrier Card
VIPC627-ET
-
VIPC627-ET is a 6U VME carrier card with four IP slots and extended temperature range. Two 50-pin, 0.1 inch flat ribbon cable connectors mounted in the front panel provide access to all IP I/O lines. Also, all I/O lines of 'IP D' are routed to VME P2 and 14 user selectable I/O lines of 'IP C' can be routed to VME P2 via a jumper field.
-
Product
6U Dual 64/100 PMC VME Carrier
V2PMC2
-
The V2PMC2 PCI-X/PMC carrier card is a 6U VME that holds up to two single-width or one double-width PCI-X/PMC modules. The V2PMC2 works in association with a PCI-Express host which is connected to it through a x4 PCI-Express serial link onto P0 connector.
-
Product
6U VME Carrier for PMCs and PrPMCs
Ti4400
-
The Ti4400 is a 6U PMC/PrPMC carrier for VME systems and forms the basis of a flexible I/O system. The user can integrate two single PMC modules or one double-wide PMC.
-
Product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
Carrier Board
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
Product
COM Express Type 6 evaluation carrier board
ATX-M-CC462-T6
Carrier Board
The ATX-M-CC462-T6 is a fully featured COM Express Type 6 evaluation carrier board designed for use with the WINSYSTEMS Intel® Tiger Lake UP3 COM Express and other COM Express Type 6 modules.
-
Product
Qseven® Reference Carrier Board
Q7-BASE
Carrier Board
Qseven is a Computer-on-Module (COM) standard for small sized and highly integrated systems adopted by SGET. The Qseven concept is an off-the-shelf, multi-vendor, Computer-on-Module that integrates all the core components of a common PC and is mounted onto an application specific carrier board. Qseven modules have a standardized form factor of 70 mm x 70 mm or 40 mm x 70 mm and have specified pinouts based on the high-speed MXM connector, regardless of the vendor. The Qseven module provides the functional requirements for an embedded application, which include, but are not limited to, graphics, audio, mass storage, network and multiple USB ports. A single ruggedized 230 pin MXM connector provides the carrier board interface to carry all the I/O signals to and from the Qseven module. This MXM connector is a well-known and proven high-speed signal interface connector that is commonly used for -PCI Express graphics cards in notebooks.
-
Product
COM Express® Type 7 Reference Carrier Board in ATX Form Factor
Express-BASE7
Carrier Board
The Express-BASE7 is an ATX size COM Express Type 7 reference carrier board. Together with the COM Express Type 7 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
PXI FPGA Module
FIO168
Carrier Board
Using OpenATE USB/PXI FPGA Carrier, you can develop your design to define custom I/O and control Hardware without prior knowledge PCI I/O and USB interface.
-
Product
Development Board
SOM-DB5800
Carrier Board
Development Board for COM Express® R2.1 Type 6 / 10 Modules. Development Board Compliant to PICMG COM.0 R2.1 Type 6 / 10 Pin-out. Support COM Express Basic, Compact & Mini modules. Expansion: PCIe x16, PCIe x4, PCIe x1, Mini-PCIe, Express Card.
-
Product
3U CompactPCI® Single 64-bit PMC Slot Carrier Board
cPCI-8301
Carrier Board
- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- Supports one single-size 32,64-bit/33,66 MHz PMC site in 4HP width- Universal V(I/O) decided by backplane- Comprehensive EMC shielding
-
Product
Carrier Board Design and Software Verification Computer-on-Module Starter Kit
Starter Kit - ETX
Carrier Board
- ETX module of choice- CPU, Memory of choice- Thermal Solution (heatspreader, and heatsink) of choice- Reference Carrier Board- Schematics, Design Guide, and User Manuals- ADLINK USB Stick with Documentation, Software
-
Product
Carrier Boards
ROM-DB7503
Carrier Board
ROM-DB7503 is the Referenced Carrier Board designed for Advantech's Qseven 2.1 module. It i provides a thorough environment for module board evaluation with its completefunction support. it's more easier for the end user to design portable devices by referring ROM-DB7503 design.
-
Product
COM Express Type 10 Reference Carrier Board
miniBASE-10R
Carrier Board
The COM Express approach of custom carrier combined with off the shelf system cores is an excellent solution when you need to customize but lack the time or quantity for a complete redesign. It fits most system integration projects with production volumes from 500 to 10,000 pcs per year. The COM Express concept has a great many advantages over full custom designs, it reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time. The average time to design a carrier board is less than half the time of a full custom OEM board.
-
Product
3U CompactPCI Serial MXM GPU Carrier Card
cPCI-A3MXM
Carrier Board
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP (100mm x 160mm)- Compatible with MXM Type A (82 mm x 70 mm) or Type B (82 mm x 105 mm)- Support NVIDIA A1000 with 2048 CUDA® cores, 16 RT Cores and 64 Tensor Cores or NVIDIA RTX™ A4500 with 5888 CUDA® cores, 46 RT Cores and 184 Tensor Cores- 4x DisplayPort 1.4, support 4K (3840x2160) resolution- Operating temperature: -40°C to +70°C- Designed to meet EN50155 standards
-
Product
3U CompactPCI® Serial XMC Module Carrier Blade
cPCI-A3XMC
Carrier Board
- 3U 4HP CPCI-S.0 peripheral- One XMC slot- Operating temperature: -40°C to 85°C with qualified components
-
Product
VME64x IP Carrier Module
DP-VME-5121
-
Data Patterns DP-VME-5121 VME IP carrier board is a 6U VME bus card that provides an electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.Each IP module supports two interrupt requests. The VME bus interrupt level is software programmable. The software configured interrupt modes are:a.Single level interrupt mode: All IP module interrupts can be mapped to a single VME bus interrupt level.
-
Product
3U CompactPCI Serial M.2/U.2/SATA Storage Carrier
cPCI-A3H20
Carrier Board
- 1x NVMe M.2 and 1x NVMe U.2 drive slot- 1x optional SATA 6Gb/s M.2 drive slot shared space with NVMe U.2- Status LEDs on faceplate: drive activity, hot-swap status, user-configurable- Operating temperature: -40°C to +85°C with qualified modules- EN50155 compliant
-
Product
M/MA Module Carrier
VX405C
Carrier Board
The VX405C carrier provides the mechanical and electrical interfaces between the VXIbus and up to six (6) VITA 12-1996 standard M/MA-Modules. The carrier provides VXI register configuration and access to the M/MA-Module I/O space and memory (if present). Each M/MA-Module is controlled separately and appears as a different logical address in the VXI environment. Over 100 M/MA-Modules are available that can provide custom interfacing to the unit under test (UUT). Up to six (6) unique interfaces may be provided in a single VXI slot.
-
Product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
Carrier Board
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
Product
COM-HPC Client Type Reference Carrier Board in ATX Form Factor
COM-HPC Client Base
Carrier Board
The COM-HPC Client Base is an ATX size COM-HPC Client Type reference carrier board based on PICMG COM-HPC Revision 1.0. Together with the COM-HPC Client Type module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
VME Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
AVC-2
-
VME64x (6U) generic carrier card for PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
Product
COM-HPC Server Type Reference Carrier Board in Extended ATX Form Factor
COM-HPC Server Base
Carrier Board
The COM-HPC Server Base is an extended ATX size COM-HPC Server Type reference carrier board based on PICMG COM-HPC Revision 1.0. Together with the COM-HPC Server Type module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
Development Board
SOM-DB5920
Carrier Board
Development Board for COM Express® R3.0 Type 7 Modules. PICMG COM.0 R 3.0 Type 7 Pin out. COM Express ® Basic/Compact module, 10 Gigabit Ethernet support by OCP mezzanine card. Extension: PCIe x16, PCIe x8, 2 PCIe x4.
-
Product
VME
-
One of the world's leading architectures for high reliability electronics applications is the VME platform.The VME standard is managed by the VME bus International Trade Association, VITA.Embedded computing's most successful bus standard, VME bus, shows no signs of slowing down as it maintains it's position as the industry's de facto standard into the 21st century. The foundation of VME's longevity, namely it's steady rate of technological evolution combined with a commitment to backward compatibility with legacy hardware and software, has been the linchpin of it's popularity for nearly twenty-five years. Today, innovative enhancements to the standard, through the VME Standards Organisation (VSO), continue to improve VME bus' speed, performance and reliability, strengthening it's position as the ideal solution for today's increasingly stringent commercial, industrial and military system requirements (Source: VITA).Data Patterns has implemented a number of standard VME boards, driven by Customer needs for Processor and I/O requirements in this platform. Today, standard modules are available covering the needs of:
-
Product
Carrier Card
CPMC1
-
The CPMC1 PMC carrier board is a mechanical adapter that holds one PMC in a 3U CompactPCI slot. The carrier supports air and conduction cooling as well as front and rear I/O. The operating temperature range is -40°C to +85°C.
-
Product
FPGA/FMC Carriers
-
Our AMC FPGA modules feature Altera Stratix IV, Altera Stratix V, Xilinx Virtex-5, Xilinx Virtex-6, Xilinx Zynq, Xilinx Artix, Xilinx Virtex-7 and Xilinx Kintex-7 FPGAs. We also offer a range of carriers that can accommodate standard FMCs featuring FPGAs from Altera and Xilinx, including the new Xilinx UltraScale family.
-
Product
VME 3U
129-130-30-31
-
Hartmann Electronic is an industry leader in the designing, manufacturing and production of backplane technology, including VME and VME64x. Over the evolution of its near 40 years of existence, VME-bus has become a worldwide standard and is still used in a wide variety of applications across many different markets.
-
-
Product
Carrier Card
PEX442
-
The PEX442 Mezzanine Carrier Card allows designers the flexibility to extend and expand the IO capability of their systems by supporting high bandwidth links to combinations of XMC, PMC and AFIX (Additional Flexible Interface Xtensions) modules using PCI Express infrastructure.
