Thermocouple Loggers
Data Acquisition from thermocouples and data record of termperature events.
See Also: Temperature Loggers
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Battery Data Logger
BDL-3926C
-
Kongter Test & Measurement Co., Limited
BDL-3926C Battery Data Logger is wireless monitoring device for string voltage, cell voltage, current and temperature. It works individually to reflect battery status or co-works with Kongter’s other battery test equipments like battery charger and K-3980 DC load bank. For different battery systems, it has customized configuration from 12V to 480V or upper. And it has easy expansion for all battery systems.
-
Product
Thermo Hygrometer Data Logger
HD2101.2
-
Thermo hygrometer, datalogger, instrument measuring range for temperature -200°C...+650 °C; for humidity 0...100% RH.
-
Product
AC/DC MilliGaussmeter With Data Logger
IDR-322
-
Integrity Design and Reseach Corp.
Unique product Frequency indicatorScale: +/-(4, 40, 400, 4000 mG)Portable and easy to use4 AA Alkaline Batteries includedTrue RMS measurement with peak holdOne volt full scale Analog Output
-
Product
Thermocouple Kit
34307A
-
The Keysight 34307A is compatible with the Keysight 34970A Data Acquistion/Switch Unit. The 34307A can also be used with the Keysight 34401A, 34460A or 34461A, however, an external program is required to convert the voltage measurements to temperature and an ice bath or electronic reference junction must be used.
-
Product
Logger version conductivity and temperature sensor with wiper
INFINITY-CTW ACTW-USB
-
Infinity-CTW is an autonomously deployable data logger for highly accurate temperature and salinity measurements during long-term periods. The instrument has a mechanical wiper that periodically sweeps the sensing surface of the seven-electrode conductivity cell to keep the initial accuracy, avoiding bio-fouling without chemical materials and frequent maintenances. Infinity-CTW allows for accurate and stable salinity measurements for several months without cleaning maintenances. Infinity-CTW performance was evaluated and reported by Alliance for Coastal Technologies, ACT code: VS09-06).
-
Product
FlashLink HVAC PDF Data Logger
-
This reusable temperature logger is a valuable tool for contractors to troubleshoot problems and validate proper function of HVAC/R systems. Temperature verification is an important part of managing equipment and facilities, and the FlashLink HVAC PDF Data Logger is a cost effective solution for accurately monitoring conditions and providing a PDF report with a graph of time-temperature data. Its small, compact design makes it easy to carry to job sites
-
Product
K-Type Thermocouples Wire, Fiberglass (32 deg F to 900 deg F) 1 m
745690-K001
Thermocouple Contact (ITA)
K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
Calibration Cable, 78-pin D-type, Thermocouple Simulator Modules
40-975-078-1m
Calibration Cable
This cable assembly is specifically designed to connect to the 78-Pin D-Type port on the front panel of Pickering Interfaces Thermocouple Simulator Modules 41-760 and 41-761 enabling calibration via an external DMM.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Thermometer Hygrometer Data Logger
S3120E
-
Data logger is designed for record of temperature and humidity. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper communication adapter.
-
Product
Tool, Crimp, TriPaddle (10 amp), Thermocouple, Micro Power, Receiver and ITA , Locator Required
910101102
Crimp Tool
This crimp tool can be used to crimp 10 Amp TriPaddle contacts, Thermocouple contacts or Micro Power contacts. Locator required.
-
Product
3D Acceleration Logger Sensor
NUL-227
-
This is a 3D (three dimensions) acceleration sensor which displays each dimension one at a time. It allows measuring the acceleration of moving bodies such as a body oscillating in a spring or in a moving vehicle.
-
Product
K Thermocouple Surface Probe
TP754
-
Surface thermocouple Type “K” probe. Tolerance according to IEC 60584-2 standard.
-
Product
Power Analyzers - Meters - Loggers
-
Full line of power and power quality analyzers, loggers and meters including for extending measurement ranges. The wide range of applications include electrical monitoring, harmonic detection & analysis, utility testing, energy management, power factor analysis and correction, power demand and consumption, kW measurement, industrial power systems, and commercial maintenance.
-
Product
Data Logger
S7841
-
Four-channel data logger is designed for record of two-state events. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper communication adapter.
