Instrumentation Amplifiers
A type of operational amplifier used when a circuit needs accuracy and stability.
See Also: Instrumentation, Amplifiers, Instruments
-
Product
Life Science Instrumentation
-
With a wide spectrum of Teledyne technologies such as high-performance cameras, sensors, automation and pumps, OEM solutions serves the vast Life Science industry in many ways.
-
Product
Instrumentation
-
Test instruments, Switching & RFIUs, and Test, Simulation, & Avionics Interfaces.
-
Product
Network Analyzer Instrument State Utility
VNAState
-
The VNA Instrument State Utility works with the most popular Vector Network Analyzers from Agilent / HP. It retrieves the instrument state information (frequencies, calibration, markers, etc) and stores it on disk in the PC as an "IST" file (meaning Instrument STate). The data can then be downloaded into the instrument at a later date.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Headphone Amplifiers
-
Applied Research and Technolgy
Drive in-ear monitors, tap a speaker line when a monitor isn't available, and make sure the whole band can hear everything they need.
-
Product
Standard & High Speed Amplifiers
-
Advanced Energy's Trek high voltage power amplifiers employ unique and proprietary circuitry. Benefit from closed-loop amplifier systems that feature exceptional DC stability and excellent wideband performance characteristics. And thanks to all-solid-state designs, our amplifiers are protected from output short circuits and overvoltages.
-
Product
Power Amplifiers
-
Your ultimate solution for sound distribution in the contractor/install market.
-
Product
Handheld Instruments
-
Measuring DC and AC voltages up to 1000 V.Alternating current and direct current with resolution up to 0.01 mA.Measuring continuity, resistance, diodestest, capacity, frequency.MIN / MAX recording.CAT III 1,000 V, Cat IV 600 V; IP54.Wireless remote display. Smartphone connection.Fluke Connect Mobile App for Android and iOS, compatible with over 20 different Fluke products.
-
Product
900 MHz Trunk Hybrid Amplifier
AS 1111
-
Hybrid Amplifier used in trunk and branch lines specially designed to serve the need of cable systems with long trunk cables. They incorporate Good Quality Hybrid IC Module to obtain better features.- Frequency Range: 40 ~ 900 MHz- Output Level: 102 dBµV- Separate IN & OUT Fuses- Level Flatness: ±0.75 dB- 32 dB Gain (40 dB Optional)- Incorporates Good Quality- Hybrid IC Module- Hybrid IC Protected
-
Product
Analog Summing Amplifier
SIM980
-
Stanford Research Systems, Inc.
The SIM980 Summing Amplifier has four input channels that can be added or subtracted from each other. The output noise is less than 60 nV/√Hz, and crosstalk between channels is less than -80 dB. With a bandwidth of 1 MHz, a slew rate of 40 V/ms, and input offsets that are trimmed to ±100 µV, the SIM980 is extremely useful in many analog applications.
-
Product
PXIe-6570, 100 MVector/s, PXI Digital Pattern Instrument
785283-01
Digital Pattern
100 MVector/s, PXI Digital Pattern Instrument—The PXIe‑6570 is designed for semiconductor characterization and production test. It includes the Digital Pattern Editor for configuring pin maps, specifications, levels, timing, and patterns. The PXIe‑6570 also includes debugging tools like Shmoo, digital scope, and viewers for history RAM, pin states, and system status.
-
Product
Instrument Systems LED Measurement Accessories
-
Konica Minolta Sensing Americas, Inc
It’s critical to use the appropriate LED measurement equipment and accessories when evaluating an LED’s various photometric and radiometric quantities. Because all of the test adapters Instrument Systems designs are compliant with CIE 127:2007, users are assured of compatibility between measurements. Instrument Systems has a diverse array of LED Measurement Equipment.
-
Product
LINEAR AMPLIFIERS
-
These amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance and fast response. The output is linear from DC up to megahertz range.
-
Product
Hydrocarbon Instruments
-
Teledyne Advanced Pollution Instrumentation
Teledyne API has developed a hydrocarbon instrument using patented gas chromatograph (GC) technology, in combination with well-characterized and familiar Flame Ionization Detection (FID). This instrument uses a new modular hardware and electronics architecture which is the basis for Teledyne API's new N Series platform. The instrument platform is thoughtfully designed for reliability, ease of operation and maintenance, low power consumption, and advanced communications and diagnostic capabilities.
-
-
Product
Data Acquisition Instrument
-
Elsys is your experienced partner when it comes to high-quality measuring devices and associated software. Whether you want to record current, voltage, strain, pressure or digital signals – Elsys offers you flexible and quickly customizable solutions for your individual data acquisition device – turnkey and from a single source.
-
Product
Amplifier, Switch and Test Box
CLIOQC Model V
-
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
Product
PC/104-GPIB, ISA GPIB Instrument Control Device
778041-02
GPIB Controller
ISA GPIB Instrument Control Device - The PC/104-GPIB is a plug-and-play IEEE 488 interface for industrial environments. The PC/104-GPIB performs the basic IEEE 488 Talker, Listener, and Controller functions required by the IEEE 488.2 standard. The PC/104-GPIB includes a license for the NI-488.2 driver software, which provides high performance and maximum reliability for connecting to third-party instruments using GPIB. The PC/104-GPIB is software- and register-compatible with the AT-GPIB/TNT.
-
Product
Distribution Amplifiers
-
Distribute time code, radio frequency and other electronic impulses. Click a model below to learn more.
-
-
Product
Process Ozone Instruments
-
Teledyne Advanced Pollution Instrumentation
All of our instruments are designed meet the rigorous demands of ambient air quality, stack, or industrial process gas monitoring. Below is a list of a range of Teledyne API process ozone instruments.
-
Product
PXI Switching Instrumentation
-
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
Product
Instruments
-
Designed to be the best for field operations, the OROS 3-Series instruments offer the capabilities of advanced laboratory instruments in a rugged and portable package that takes any measurement situation in its stride. From 2 to 32 channels, FFT analyzers can be cascaded and distributed to measure up to 1000 channels.
-
Product
Rackmount or compact airborne state of the art Solid State Power Amplifiers
SSPAs
-
Broadband off the shelf or custom designed RF/Microwave SSPAs as airborne baseplate miniature modules or as 19" 3U compact rackmount AC units, CW or Pulsed operation from 100W to 1KW up to Ku frequency band.
-
Product
Voltage And Current Amplifier
KINGSINE KA30 / KA60
-
KINGSINE Electric Automation Co., Ltd.
KINGSINE's KA30 / KA60 voltage and current amplifier is high accuracy, high power, Panel-mounted type real time simulation power amplifier with four-phase voltage and three-phase current.
-
Product
Power Amplifier
MS 2011
-
Power Amplifier is used to amplify the RF signals from low power to 100 Watts of RF carrier power to 400 Watts Peak envelop power (single side band operation). Outputs are filtered. This system is controlled through microprocessor and it has RS485 interface.
-
Product
PCI Express, IEEE 488 GPIB Instrument Control Device for Linux
779779-01
Controller
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
Product
Amplifier Systems Band Specific
-
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
Power Amplifier, RF
-
Is a type of electronic amplifier that converts a low-power radio-frequency signal into a higher power signal. Typically, RF power amplifers drive the antenna of a transmitter.
-
Product
Dual-Mode Charge Amplifiers
-
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
