-
Product
AC/DC Power Supplies
-
At ABSOPULSE Electronics, we specialize in the design and manufacture of heavy-duty custom and semi-custom AC-DC switching power supplies, rectifiers and battery chargers.We can meet any AC to DC input/output configuration requirement, with output power ranging from a few watts to several kilowatts.ABSOPULSE's rugged power supplies are typically designed and built for an operational life of 20 to 30 years in harsh environments.
-
Product
4kW Electronic Load
PT04-110
-
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 110V and 48V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
Product
High Voltage Power Supplies
-
FuG high-voltage power supplies of all types except HYN are primary switched-mode power supplies with pulse width modulation . The rectified mains voltage is chopped into square pulses of constant frequency, transformed, rectified and smoothed. The square-wave voltage is pulse-width modulated for regulation.
-
Product
HIGH VOLTAGE SCR CONTROLLED POWER SUPPLY
xPS Series
-
High Voltage SCR Controlled Power Supply, P/N 18278PS Power Rating: 350 KW. Input: 480 VAC, 3 PH, 60 Hz Output: 0 to 5000 VDC, 70 Amps max Ripple: 2 % approximately at maximum rated voltage Configuration: 12 pulse externally SCR controlled rectifier system Protection Devices: Input contactors Overload relay shutoff Input surge suppressor Thermal switches Output current limiting resistor (made with 5 Ohm Kanthal heating element) Emergency power shutoff Cooling: Each 6 pulse rectifier assembly is cooled by three 10” fans Interface: 4/20 ma converter interface for output voltage and output current to SCR controller. Enclosure: The overall dimension of the unit is (78”H x 38”W x 53”D). It is comprised of two separate enclosures each with dimensions of (78” H x 38” W x 26” D) which are integrated together to form a single enclosure. Each half enclosure has one 6 pulse transformer and one 6 pulse high voltage rectifier. Weight: Approx. 5000 lbs. SCR Controller: The 12 pulse SCR controller is supplied by the customer. We were responsible for the 12 pulses Transformer and 12 pulses Rectifier section. Portability: Unit can be lifted up with a fork lift. It can also be moved around with a 5000 lb pallet jack. Transformer: Two 200 KVA transformers are used to step 480 VAC to 3750 VAC each in a 12 pulse configuration Rectifiers: Two 6 pulse rectifier assemblies capable for 5000 VDC and 60 Amps output were used. The high voltage rectifier assemblies are isolated and protected in a fiberglass plenum within the enclosure. Blocking Diode: Each diode of the 6 pulse rectifier consists of 10 diodes in series to offer a blocking voltage of 12000 V (PIV)
-
Product
Power Discrete Tester
Mostrak-2
-
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
Product
Repair of Six Diode Bridge Assemblies, P/N 5989C
-
CEHCO is specialist in repair of various rectifier assemblies. One such assembly is shown below:Specifications:- Six Diode Bridge Assembly, P/N 5989C- AC input terminals: (3, 4 , 5)- DC output terminals: (1), POSITIVE and (2), NEGATIVE
-
Product
Ampere Hour Meter Module
TE2504
-
Ampere Hour Meter Module- Model TE 2504 is basically managed for ready setup or the usage can be seen in where the current requirement are low. This one is used which is ready to be applied in the stand alone panel and advanced from all the former models, IM2501, IM2502 and IM2503. These are basically panel mount instruments which are required to rectified in the rectifier or in an independent panel.
-
Product
Independent Operation AC Generator Excitation Regulator
SVRi
-
Kinetics Control Systems SVRI Exciter/Regulator rectifier is designed and rated in capacity for the application of exciting the DC fields of an AC generator operating independently with other generators and/or NOT tied into a utility power grid.
-
Product
Bridge Rectifier Diodes
-
ST’s portfolio of bridge rectifier diodes is intended for primary bridges. In input primary bridge applications, ST's 1200V bridge diodes achieve very low conduction losses thanks to very low forward voltage characteristics. They can operate at up to +175 °C junction temperature, as a result of reduced leakage currents. Bridge rectifier diodes are belonging to the STPOWER family.
-
Product
M Series Panel Meters
ST-66
-
Standard Electric Works Co., Ltd
● M Series all up to 15A● Case and Composition：Acrylic resin front and ABS resin case. Four studs mounting.● Accuracy：Moving coil type : Class 2.0 Rectifier type : Class 2.0● Color：Black case, white scale plate.● Pointer：Tube type, color in black or red.
-
Product
Battery Charger Meters
-
A range of ammeters and voltmeters with tough moving magnet or polarised moving iron movements designed for low cost indication of d.c. or rectified a.c.
-
Product
Resistive & Capacitive AC Load Bank
RCD
-
RCD AC load banks are used to test the REAL working condition of UPS, rectifier, inverter and etc who are loaded by non-linear or electronic load with non-constant resistance such as computer, networking equipments and etc. Through the accurate detection of its output and power quality, users could avoid the inadequate loading capacity or cause pollution to power grid, so as to guarantee supply security. JUNXY RCD load banks leading power factor loads are created to debug power supply system parameters such as its crest factor test.
-
Product
Rotating Electrical
-
Through its vast distribution network, WAI provides customers in the aftermarket with access to a wide range of product lines they need, when they need them. WAI’s production team is committed to consistently being the First-to-Market with the latest model products. This commitment, paired with the skill and expertise of the team, results in the introduction of more than 500 new products to the aftermarket each year. WAI offers 100 percent new alternators and starters as well as generators, motors, voltage regulators, rectifiers and other components for the Rotating Electrical market.
-
Product
Switch Mode Power Supplies-Water Cooled
-
The MSW Rectifiers are based on Switch Mode Technology. This reliable technology assures excellent quality DC currents with a ripple of < 3% and a control accuracy of less than 1%.The MS-Series features constant voltage and current control with easy, quick installation and maintenance. Modular versions easily increase the output by means of series or parallel connection. All models have DC short circuit protection. With forced air-cooled models, the cooling air quantity is controlled in relation to the load reducing contamination and noise levels.
-
Product
"Stiff Grid" and Parallel Operation AC Generator Excitation Regulator
SVRFP
-
The Kinetics model SVRFP Exciter/Regulator rectifier is designed and rated in capacity and operating parameters for the application of exciting the fields on an AC generator in parallel with other AC generators and the power system is a "stiff system" in relation to loading. A "stiff system" is a generating system that is of sufficient capacity or the generator is "small" in relation to the system grid, that the AC system voltage under impulse/step loading condition does not require forcing of the generator field to maintain the power grid voltage. Systems are designed with a standard unit service factor to operate within the +10% to -20% nominal voltage rating at 100% current rating.
-
Product
Fluorescent Lamp Asymmetric Pulse Tester
UI2002C
-
UI2002C is designed according to the latest update in IEC 61347-2-3 about the test requirements for local rectifying effects on tubes. It imitates the condition when tube is under local rectifying status and tests the abnormal protection function of ballast by adopting fluorescent lamp asymmetry pulse test method with 3 windows for displaying rectified voltage, rectified current, and rectified power. It is easy for operation and with high test accuracy. • Measure lamp voltage, lamp current , average and total power of lamp. • Lamp voltage range: 10~300V • Lamp current range: 10mA~1.0A • Lamp power range: 0.5~300W • Tolerance is 5%
-
Product
Megohmmeter
1864-9700
-
The GenRad 1864 Megohmmeter is the choice for more demanding applications. The test voltage can be set to any value from 10VDC to 109VDC in 1-volt steps and to 1090VDC in 10 volt steps. Thus the GenRad 1864 can be set to any common, or uncommon test voltage for ceramic, mica or paper capacitors, or other devices. The reverse resistance of rectifiers can be readily measured; the low test voltages are especially useful in measuring solid state diodes. An additional range on the 1864 Megohmmeter permits measurements up to 200 T (2 x 1014)
-
Product
Transformer Turns Ratio Testers
-
Transformer turns ratio testers from TRT series are DV Power instruments mainly designed for the measurement of power transformer turns ratio. Also, they measure transformer excitation current and phase shift. Special tests, such as automatic vector group detection and magnetic balance, can be performed on three-phase transformers and three-phase autotransformers.All models, except TRT03 series, have a built-in true three-phase power source, which is necessary for testing turns ratio of transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.DV Power turns ratio testers can output various test voltages for different applications. From the extremely low test voltage of 1 V AC that enables turns ratio verification of the majority of current transformers, up to the highest test voltage of 500 V AC that provides the most accurate turns ratio testing of power transformers used in power generation and transmission. By using the external booster, test voltage increases up to 5 kV AC in order to successfully test capacitive voltage transformers.All DV Power turns ratio testers have a built-in tap changer control unit. Because of that, it is possible to control the on-load tap changer (OLTC) directly from the device. In order to make the most out of this feature, the instrument and included DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions, and saving results. This option significantly facilitates and shortens the turns ratio testing time.TRT turns ratio testers use the same set of cables as three-phase winding ohmmeter & tap changer analyzers from the TWA series. Consequently, it enables one-time cable setup for performing eight tests:turns ratioexcitation currentphase anglemagnetic balancevector group detectionwinding resistanceon-load tap changer DVtestand demagnetization.
-
Product
12 Pulse Diode Bridge Rectifiers Inside Fiberglass Plenums, P/N 5872C4-2
-
- 12 Pulse Diode Bridge Rectifier, P/N 5872C4-2- Each diode is rated for 60 Amps, 1800 Volts peak- Dimensions: 50″L x 40″W x 20″H approximately- Four 10″ fans are used for coolingFour 10″ fans will force cool from the bottom of the Plenum. 12 diode assemblies (each diode consists of nine diodes in series are integrated together inside the Plenum). The output is rated for 3000 VDC, 80 Amps.
-
Product
F Series Panel Meter
ST-90U
-
Standard Electric Works Co., Ltd
● Hz Meter : Measuring Ranges : 45~56 Hz, 45~55 Hz, 55~65 Hz Rated Voltage : 110V, 220V Accuracy : Class 2.0 Consumption : Max. 15mA Test Voltage : 2kV. 50-60 Hz● Case and Composition: Polycarbonate front and Polybutylene Terephthalate(PBT). Three studs mounting.● Accuracy : AC class 2.5 DC class 2.0 Rectifier class 2.0● Color：Black case and white scale plate.● Pointer：Sword type color in black.
-
Product
P Series Panel Meters
ST-60
-
Standard Electric Works Co., Ltd
● DC up to 30A● AC up to 30A● Case and Composition: Acrylic resin front. Bakelite case. ABS case. Four studs mounting.● Accuracy :DC : Class 2.0 AC : Class 2.5 Rectifier : Class 2.0● Color：Black case, white scale plate.● Pointer：Tube type, color in black or red.
-
Product
S Series Panel Meter
ST-670B
-
Standard Electric Works Co., Ltd
● DC up to 50A● AC up to 30A● Case and Composition: Acrylic resin front and Bakelite case. Four studs mounting.● Accuracy : Moving coil type：Class 2.0 Moving lron type：Class 2.5 Rectifier : Class 2.0● Color：Black case. white scale plate.● Pointer：Tube or knife-type, color in black or red.
-
Product
P Series Panel Meters
ST-70P
-
Standard Electric Works Co., Ltd
● DC up to 15A● AC up to 30A● Hz Meter : Measuring Ranges : 45~55 Hz, 45~65 Hz, 55~65 Hz Rated Voltage : 110V, 220V Accuracy : Class 2.0● Case and Composition: Acrylic resin front. Bakelite case. ABS case. Four studs mounting.● Accuracy :DC : Class 2.0 AC : Class 2.5 Rectifier : Class 2.0● Color：Black case, white scale plate.● Pointer：Tube type, color in black or red.
-
Product
Rectifier
-
An electrical device that converts alternating current, which periodically reverses direction, to direct current, which flows in only one direction.
-
Product
DC Filter Inductors
-
Osborne DC filter inductors (aka filter chokes) are commonly used in AC to DC conversion circuits to present an inductive voltage drop to the AC component of rectified current. This inductive voltage drop acts as a filter. Osborne designs filter inductors to components to function effectively (without saturation) in the presence of the DC current. Osborne will work with you to mitigate the impact of ripple frequency in conversion circuits. Every Osborne DC filter choke is designed for high performance with special consideration given to your circuit´s power supply frequency and conversion configuration.
-
Product
Thyristors (SCR)
-
Featuring immunity to surges and transients in static states and commutations, our silicon-controlled rectifiers (SCR), also known as thyristors, are ideal for single- and three-phase power line networks, even in harsh environments up to 150°C. Thyristors (SCR) belong to our STPOWER family.
-
Product
Stationary Industrial And Railway Power Supply
-
For decades, Gustav Klein has been supplying safe power supplies for industry and railways, such as rectifiers, inverters, DC converters, UPS and BSV systems, as well as frequency converters with a fixed output frequency.
-
Product
AC and DC Electronic load
63800 series
-
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing thereby giving reliable and unbiased test results. The 63800's state of the art design uses DSP technology to simulate non-linear rectified loads with its unique RLC operation mode. This mode improves stability by detecting the impedance of the UUT and dynamically adjusting the load's control bandwidth to ensure system stability. Comprehensive measurements allow users to monitor the output performance of the UUT. Additionally, voltage & current signals can be routed to an oscilloscope through analog outputs. The instrument's GPIB/RS232 interface options provide remote control & monitor for system integration. Built-in digital outputs may also be used to control external relays for short circuit (crowbar) testing.
-
Product
P Series Panel Meters
ST-80
-
Standard Electric Works Co., Ltd
● DC up to 50A● AC up to 50A● Hz Meter : Measuring Ranges : 45~55 Hz, 45~65 Hz, 55~65 Hz Rated Voltage : 110V, 220V Accuracy : Class 2.0● Case and Composition: Acrylic resin front. Bakelite case. Four studs mounting.● Accuracy :DC : Class 2.0 AC : Class 2.5 Rectifier : Class 2.0● Color：Black case, white scale plate.● Pointer：Tube type, color in black or red.
-
Product
S Series Panel Meter
ST-670R
-
Standard Electric Works Co., Ltd
● DC up to 10A● Case and Composition: Acrylic resin front and Bakelite case Two studs mounting● Accuracy : Moving coil type：Class 2.0 Moving lron type：Class 2.5 Rectifier : Class 2.0● Color：Black case. white scale plate.● Pointer：Tube or knife-type, color in black or red.
