Regulated DC Power Supplies
Clip unregulated (varying) source of DC voltage at a specified level to supply regulated (steady) voltage to a load. (allaboutcircuits.com)
-
Product
6 Channel 4 kV/3 mA VME HV Power Supply Module
V6533
-
The V6533 is a 1-unit wide VME 6U module housing 6 High Voltage Power Supply Channels 4 kV, 3 mA (9W max). The board is available with either positive or negative output polarity; mixed version with 3 positive and 3 negative channels is also available.
-
Product
DC Electronic Load
EE30141A
-
The EE30141A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices
-
Product
Universal AC-DC Power Supplies
PS-RS25-5
-
WINSYSTEMS’ PS-RS25-5 is a small, convection cooled 25W power supply for embedded systems. It is a universal design that accepts 88 to 264VAC input and generates up to 5A of current at +5 volts. The +5 volt output can be adjusted with an on board trimpot. The PS-RS25-5 is small, measuring only 79 x 51 x 28mm.
-
Product
Power Splitter, DC to 26.5 GHz
11667B
-
The Keysight 11667B power splitter is recommended when making wideband ratio measurements using a Keysight 8757 scalar network analyzer. This two-resistor type power splitter provides excellent output SWR at the auxilliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from dc to 26.5 GHz allows wideband measurements to be made with a minimum of uncertainty.
-
Product
6 Channel 500 V/3 mA VME HV Power Supply
V6519
-
The V6519 is a 1-unit wide VME 6U module housing 6 High Voltage Power Supply Channels 500V, 3mA. The board is available with either positive or negative output polarity; mixed version with 3 positive and 3 negative channels is also available.
-
-
Product
High-Performance Autoranging DC Power Module, 60V, 20A, 300W
N6754A
Power Module
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance are standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 - 300 W.
-
Product
DC Load Bank
K-900
-
Kongter Test & Measurement Co., Limited
K-900 series are your best choice DC load bank with Kongter’s updated solutions. This new series resistive dummy load includes a series customized load bank models that feature rugged design and and excellent performance. They facilitate your work for DC load and battery capacity testing. With different models of DC load bank, it covers a wide range from 12V to 480V nominal voltages with current up to 600A. Its big TFT touch screen with vivid display makes it more user-friendly for setting and operation. Kongter’s new PC software make it easy for measurement monitoring and report print out.
-
Product
Programmable AC&DC Power Supply Unit
PADS
-
The energy feedback type programmable AC/DC power source with energy feedback unit equipped functions of voltage adjustable, frequency adjustable, harmonic controllable, low voltage ride through simulation etc.
-
Product
Triple Output Power Supply
U8030 Series
-
The Keysight U8030 Series variable DC power supply has a total output of 375 W—making this solution an ideal power source in the design and manufacturing of electronic devices. The U8030 Series power supplies feature an output sequencing capability for semiautomated tests. These power supplies enable you to generate output sequences with minimal programming skills. This solution features excellent load regulation and clean output noise for continued stability.
-
Product
Bench Power Supplies
-
For more than 50 years, Keysight's power supplies have been changing the way engineers prove their design, understand issues, and ensure product quality. Our bench power supply products provide low output ripple/noise along with layers of protection for your device. You have the option to select from full-featured programmable power supplies or simple variable DC power supplies.
-
Product
DC Hysteresis Graph
DX-2012SD
-
Automatic measurement on basic magnetization curve and magnetic hysteresis loop under static state of soft magnetic material, accurate measurement on static magnetic characteristic parameters such as initial permeability µi, maximum permeability µm, saturation magnetic induction Bs, remanence Br, coercive Hc and hysteresis losses Pu.
-
Product
100-Watt DC/DC Converter
55LS1
DC Converter
NAI’s 55LS1 is a COTS, 100 Watt DC/DC Converter that accepts a +28 VDC input and provides a single full-power output at a baseplate temperature of +100° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
Product
Software for VME Power Supply Modules
V65XX
-
V65XX Controller – Control Software for VME Power Supply Modules is a console application that allows a complete and friendly management of a single CAEN VME High Voltage Power Supply board (V65XX series), controlled via CAEN VME Bridges.
-
Product
Linear Power Supplies Programmable, Digital Control, Rack Mount, Ultra Low Ripple/Noise
Series MAT
-
Kepco MAT are linear power supplies that are oriented to systems applications. Their principal control means is a 2-wire, long range, serial bus, Kepco's single address, multiple instrument bus. As many as 27 power supplies, including models in the Kepco MST, MBT and BOP series may be "daisy-chained" on this bus and interfaced either to IEEE 488.2, a PC bus, or to a VXI host.
-
Product
RFP DC Low Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
Power, Patchcord, ITA, 36", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps)
7-251414000-036
Power Patchcord
Power, Patchcord, ITA, 36", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps).
-
Product
DC BIAS CURRENT UNIT
3265B SERIES
-
To evaluate components at currents up to 125 A the 3265B DC Bias Units are used with either the Wayne Kerr 3255B series of Inductance Analyzers or the 3260B Precision Magnetics Analyzer. When one 3265B/25A or 3265BQ/25A DC Bias Unit is connected to an instrument up to 25 A of DC bias current can be set in steps of 25 mA with one unit. Additional DC Bias Units can be added such that with five units connected in parallel it is possible to set DC bias currents up to a maximum of 125 A DC.
-
Product
DC Power Output Analysis Service
-
We will detect decrease in power output of a customer’s solar power plant caused by trouble of the panels or other system components quickly, by analyzing the monitored data.
-
Product
10 MHz To 67 GHz LAN Wide Dynamic Range Peak And Average Power Sensor
L2067XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Programmable Linear DC Power Supply
MPS-S Series
-
Triple channel programmable DC power supply is with high resolution, high precision and high stability, over-voltage and over-heat protection are available. Series and parallel operation are also provided. The resolution is 10 mV/1 mA.
-
Product
Narrow Profile Power Supplies
-
Where only a narrow mounting space is available, Acopian Narrow Profile power supplies fit where many others cannot. Choose from Series A (high performance - model numbers begin with the letter A) and Series B (general purpose - model numbers begin with the letter B) models with output ratings up to 150 volts, up to 3.5 amps.
-
Product
Programmable DC Power
TS Series
-
The TS Series utilizes the latest IGBT devices to drive down size and increase performance. The high frequency design delivers fast transient response and low output ripple. This performance coupled with Magna-Power''''s rugged current-fed power processing, enables confidence in even the most demanding applications.
-
Product
10 MHz – 18 GHz USB Power Sensor
U2000H
Power Sensor
U2000H USB Power Sensor measures average power over the frequency range 10 MHz to 18 GHz and power range -50 dBm to +30 dBm.
-
-
Product
DC Electronic Load
EE30180A
-
The EE30180A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running.
-
Product
Power Divider, DC to 26.5 GHz
11636B
-
The Keysight 11636B is a dc to 26.5 GHz power divider for direct power dividing applications. The excellent impedance match of all three ports improves fault location measurements by reducing re-reflections. The Keysight 11636B power divider/combiner is recommended when making wideband comparison measurements with the Keysight 8757 scalar vector network analyzer.
-
Product
Fiber Amplifier - Node With Supply
FANS 811-812
-
- AGC - Automatic Gain Control- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lasers with Isolators- Variable SLOPE/GAIN Control- Input Wavelength : 1310/1550nm- Output Wavelength : 1310nm- Digital Display of Optical Level- External FusesPower Options :- Mains 220VAC, 50Hz- 12V DC / 2 Amp- 40VDC from “40V/RF out” connectors
-
Product
DC Coupled Current Probe
34134A
High Current Probe
Measure a wide range of applications with this battery-powered, clamp-on probe; use with DMMs or voltmeters
-
Product
Programable Power Supply & Programable Electronic Load
PW-8033P
-
*DC 0~32V / 0~3A X 2 + Fix 5V/3A*Triple Output 207 VA High Power*4 Digits, 4 Display*Programable Control, 9 Memory*Built In USB Interface*Series 0~64V / 0~3A Operation
