Product

SAFETY TESTERS ( CURRENT LEAKAGE TESTERS )

ST-05

-

Criterion Instruments Limited

ST-05 - Criterion Instruments Limited

Safety Tester Model ST-05 is a test set for testing small equipment powered by 120V 60 Hz, from an approved U-ground source. Test also can be run on double-insulated tools an on appliances with two-pin parallel plugs.

Product

Inertial Measurement Units

IMU

-

Analog Devices Inc.

IMU - Analog Devices Inc.

Analog Devices inertial measurement unit (IMU) sensors are based on multiaxis combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors. Our technology reliably senses and processes multiple degrees of freedom, even in highly complex applications and under dynamic conditions. These plug and play solutions include full factory calibration, embedded compensation and sensor processing, and a simple programmable interface.

Product

4/5 Pin Trailer Harness Checker / Towing Maintenance Kit

#8026

-

Innovative Products of America

#8026 - Innovative Products of America

Test, clean and restore 4/5 pin trailer connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tool removes corrosion and verifies proper pin size on both male and female truck/trailer plugs. For use with 4/5 flat connectors. Patented. Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsKit Includes: #7866: 4/5 Pin Trailer Harness Checker, #8021: 4/5 Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner

Product

75 Ohm 1.6/5.6 Connectors

-

Pasternack Enterprises, Inc.

Pasternack Enterprises, Inc.

Pasternack 75 Ohm 1.6/5.6 connector category includes many part numbers, the majority are RoHS and REACH compliant. 75 Ohm 1.6/5.6 connector series in this category will terminate to coax or PCB (printed circuit board). Our 75 Ohm 1.6-5.6 connectors are built to precise industry specifications. 75 Ohm 1.6-5.6 connectors are constructed in jack or plug gender with 75 Ohm impedance. 75 Ohm 1.6/5.6 connectors are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm 1.6-5.6 connector designs include clamp/solder, crimp/solder or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 75 Ohm 1.6/5.6 connector series is in-stock. Not only are these 1.6 / 5.6 connectors in stock, but they also will ship the same day as they are purchased.

Product

AFDX ® / ARINC 664 Test And Simulation PCI Module

PC104p-429

-

SET GmbH

PC104p-429 - SET GmbH

*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems

Product

Basic Quad K-Type Analog Thermocouple Amplifier

SEN-30103-K1

-

Playing With Fusion Inc

SEN-30103-K1 - Playing With Fusion Inc

Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.

Product

Network & Cable Testers

-

Platinum Tools

Platinum Tools

Detects PoE end/mid-span voltages on network cables. LED indicators instantly show “GO/NO-GO” detection on PoE networks. Plug cables directly into the builtin RJ45 jack or use the included patch card to detect voltage in wall jacks.

Product

Loudspeaker Cable Testers

EMO E450

-

EMO Systems Canford Audio PLC

EMO E450 - EMO Systems Canford Audio PLC

The EMO E450 cable tester will test for continuity, cross connection, and open circuit in cables fitted with NL8FC 8-pole and NL4FC 4-pole Speakon connectors, 3-pin XLR connectors, and 2 or 3 pole A-gauge jacks. EP retrofit kits are available to allow cables fitted with EP 4, 5, 6, or 8 pin connectors to be tested. The EP connectors fit in two pre-punched holes on the rear of the tester accessed by removing the blanking panel. The kit's flying leads plug directly into connectors mounted on the tester's PCB.

Product

Miller 400D

44550

-

M. C. Miller Company

44550 - M. C. Miller Company

No need to select ranges or adjust dials – the Miller 400D provides a direct read-out of resistance with the push of a button• Bluetooth interface allows optional data-logging via a Bluetooth-enabled PC (or PDA)**• Rugged, hard plastic case - safe to use on wet ground – IP67 rating for dust and water intrusion• Resistance measurement range from 0.01Ω to 10MΩ (auto-ranging) • High resolution digital display• Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 82.2Hz (the unit’s operating frequency)• Runs on a set of replaceable D-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source• Performs 10,000 single readings on a fresh set of batteries• Integrates with Universal Rectifiers’ Soil Depth Selector/Multi-Pin Cable Harness System (please see Integration with Universal Rectifiers’ Cable Harness)

Product

Electronic Fuel Injection & Ignition Spark Tester Kit

36310

-

S & G Tool Aid Corp

36310 - S & G Tool Aid Corp

Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Contains Cat. No. 36300, Noid Light Set to test electronic fuel injection signals and the Cat. No. 23900, In-Line Ignition Spark Checker to trouble shoot the ignition system (Shows a duplicate view of the ignition spark). Supplied with Noid Lights to check Bosch PFI, Ford TBI, Geo TBI, GM PFI, GM SCPI and GM TBI.

Product

Mini Back Probes/Wire Piercers

618

-

Electronic Specialties Inc.

618 - Electronic Specialties Inc.

*Great for backprobing weather pack style connectors used with numerous automotive sensors *Also very handy for piercing and tapping readings on smaller gauge wires - using the included probe adapters *Works with most Test Lead Kits in the field - with standard 4mm banana plug test lead *Set includes four probes - red, black, green, yellow Test probes 21 mm length

Product

Noid Lights, IAC Test Lights & Ignition Spark Tester Kit

36330

-

S & G Tool Aid Corp

36330 - S & G Tool Aid Corp

Use to test electronic fuel injection signals, idle air control circuit and spark plug circuits. Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Includes 8 Noid Lights (for checking GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, BOSCH 2 and GM Multec 2; 2 IAC Test Lights (for straight and 90 applications); and Cat. No. 23900, In-line Ignition Spark Checker.

Product

IEC60884-1 Plug Socket Switch Life Tester With 3 Stations

CZKS-4

-

Shenzhen Chuangxin Instruments Co., Ltd.

CZKS-4 - Shenzhen Chuangxin Instruments Co., Ltd.

1. This test equipment is designed and manufactured according relevant requirement of Standard IEC60884-1,GB2099.1 and GB16915.1,Mainly used to test the service life of household and similar use plugs and sockets or switches. 2. This machine connect to load cabinet and conduct electrical life test ,normal operation and breaking capacity to plug socket and switch.

Product

OEM Test Leads

-

Parrot Invent

Parrot Invent

At your request , we can produce different test leads configurations with PCM, PCX, PCS Parrot Clips , silicone wire , banana plugs etc.

Product

Socket Outlet Torque Test Device

CX-LJ

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-LJ - Shenzhen Chuangxin Instruments Co., Ltd.

For measuring and testing the torque strain exerted by appliances with plug pins on socket-outlets, in accordance with IEC 60065 clause 15.4.1 and figure 11, IEC 60335-1 clause 22.3, IEC 60884-1 clause 14.23.2.

Product

3 Digit LCD Voltmeter

SP 200

-

Lascar Electronics Ltd

SP 200 - Lascar Electronics Ltd

The SP 200 is a 3 digit LCD voltmeter with 9mm (0.36") digit height and LED backlighting. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into two 6-way SIL sockets and can be fitted into a panel via the fixing clip.

Product

Bus Analyzer / Exerciser

VME850P2

-

Silicon Control Inc.

VME850P2 - Silicon Control Inc.

The VME850P2 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P2 connector. This module allows the user to monitor and stimulate the A, C and D  rows of the 160 pin P2 connector. Although the VME850P2 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P2 connector must be less then 5V in order to prevent damage of the analyzer.

Product

Test Switches and Accessories

FT Flexitest Family

-

ABB Ltd.

FT Flexitest Family - ABB Ltd.

The ABB FT test kit comes with a convenient carrying case to hold your hand held meter, test plugs patch cords, clips, and test probes in neat order. Patch cords are highly durable and flexible. Test switch accessories include: Test plugs Test kits Covers Interlocking bars Miscellaneous

Product

XL Deploy

-

XebiaLabs

XebiaLabs

Simply plug in all the tools and systems you have and you’ll be ready to deploy fast. XL Deploy works seamlessly with everything from continuous integration, provisioning, middleware, cloud platforms, and old legacy systems to the most advanced, modern architectures.

Product

In Line HT Ignition Tester

1177

-

Draper Tools Ltd

1177 - Draper Tools Ltd

Establishes whether there is a high tension spark potential at the spark plug. Hands free operation means no risk of electric shock to user. Ideal for modern vehicles with sensitive electronics. Probe is 55mm long with a lead 100mm in length.

Product

Outside Dimension (OD) Measuring Instruments

-

Pratt & Whitney Measurement Systems, Inc.

Pratt & Whitney Measurement Systems, Inc.

Can measure just about any manufactured precision part or gage such as pins, plugs, and all types of threads.

Product

Multimeter Electronic Test Leads Kit

-

AstroAI Corp.

AstroAI Corp.

VERSATILE KIT includes 2 alligator clips with removable insulation, 2 extended range plunger mini-hooks with pass-through banana plugs, 2 heavy duty test probes, 2 42” lead extensionsUNIVERSALLY COMPATIBLE with either 0.16” banana plugs or shrouded banana plugs on all ends

Product

MATCO BASIC MULTIMETER

MD251

-

Matco Tools

MD251 - Matco Tools

*Provides readings for volts, amps and ohms required for automotive electrical system tests, as well as diode and continuity tests*Beep-Jack audible warning beeps against improper a-terminal plug in and decreases the risk of damage