-
Product
PXI Mixed Configuration Relay Module - 4 Cells Populated
40-138-AA-BB-CC-DD (4 CELL)
-
The 40-138 2A Relay Module with 4 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
-
Product
Heat Exchangers RF Coaxial Loads
86500 Series
-
The 86500 Series Heat Exchangers are ideal for areas where water is limited. The loads are rugged, self-contained, easily operated, and portable units capable of dissipating up to 80 kW of RF power from DC to 800 MHz with a VSWR of 1.10:1.
-
Product
Programmable DC Electronic Load - (Economical)
63200E Series
-
The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.
-
Product
Electronical Load Board 6U VME64x (air cooled)
056-301
-
The 6U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
High Power DC Electronic Load
34000C Series（6KW~24KW）
-
34000C Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 3.5 T Axle Load with 2 x 3 kW Drive Motors and Max. Track Width of 2,500mm
C_MBT C 3.5 W250 | VP 210153
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 3.5 t axle load with 2 x 3 kW drive motors and a max. track width of 2,500 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for larger vehicles such as SUVs, off-roaders or vans.
-
Product
48V / 200 Amp Load
BD12-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
AC Load Banks
XL2000-XL3000 Series
-
Mosebach Manufacturing Company
The XL2000-XL3000 Series is a group of outdoor rated load banks ranging from 2000 kW to 3000 kW. These load banks range in features from permanently mounted with direct bus bar connections to trailer mounted and easy disconnect cam lock connections. Mosebach can also integrate a wide variety of control systems into the load bank to meet your needs.
-
Product
Oil Test Cell Heater
-
• Dry type heater for oil test cell • Temperature setting of 20º -110ºC auto cut-off • Quick heating (RF Induction) from inside & outside
-
Product
HDDH-3932 Single Cell Battery Activator
-
HD Power Test Equipment Co.ltd
HDDH-3932 Cell Activator is used to discharge and charge and activate for disable single cell battery, which is simple, safe and accurate test device.The instrument is with perfect protection function, sound and light alarm and clear interface tips.
-
Product
Load Bank
RLB
-
RARA manufactures load banks, ranging from small portable units for testing generators to multi-megawatt designs for larger applications. Regular load testing, along with correct battery maintenance, is the best way of ensuring the reliability of standby power systems. It is routine for all newly-installed generating sets to have a load test during the commissioning process in order to prove the performance of the set and all ancillaries-cooling system, exhaust system, switchgear and protection schemes.
-
Product
Saluki SEL7 Series Programmable DC Electronic Load (up to 6kW)
-
The new SEL7 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL7 series delivers high speed and high accuracy with a resolution of 0.1mV and 0.01mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL7 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.
-
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1500B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Smart Card Module Test Cells
-
Current and voltage measures are executed on defined pins, in stable conditions.Measurements:- Open/short- Input leakage current- IDD Supply instant/average current test (static/dynamic mode)- Input capacitance @13 MHz and inductance- Retro modulation index (RMI)Test of passive devices:- Capacitors- Resistors- Resonators
-
Product
Signal Module, Receiver, QuadraPaddle, 90 Series, 480 Position, Fully Loaded with Twin Female Contacts and Square Posts for Wire Wrap (610 138 200 and 610 138 118)
510150147
-
Primary mating module 510151106. (May mate with other ITA modules, as well.)
-
Product
Digital Roller Brake Tester for Cars and Vans up to 5.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,800mm
C_MBT C 5.0 W280 | VP 210160
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 5.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,800 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for large and heavy cars and vans, and with increased loads.
-
Product
Sequence Creation Software for Power Supplies and Electronic Loads
Wavy Series
-
WAVY is sequence creation software that supports the power supplies and electronic loads from KIKUSUI Electronics Corp.
-
Product
Load Pull Test Fixtures
-
Low Insertion Loss for High VSWR TuningMultiple Connector Configurations50Ω and Transformers (Klopfenstein, Quarter-wave) AvailableHeatsinks and Fans AvailableCooling (Water cooling, Forced air cooling) AvailableIntegrated Biasing Available
-
Product
AC Load Bank (Resistive/Reactive)
K-1000 Resistive/Reactive
-
Kongter Test & Measurement Co., Limited
Resistive/reactive load banks are great choices for testing turbines, switchgear, rotary UPS, generators and UPS systems. They can also be used for integrated system testing of utility substation protection systems, particularly for more complex relays like distance, directional overcurrent, power directional and others. A resistive/reactive inductive and/or capacitive load is often required to test solar inverters to ensure solar panels can be stopped from producing electricity in the event of a power outage.
-
Product
Acoustic Load Shackle
ALS-2.0
-
The Acoustic Load Shackle is designed for subsea operations where load monitoring is required, either for short term operations lowering an item to the seabed or for longer periods monitoring dynamic loads.
-
Product
Liquid-Cooled Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
EMAX's liquid-cooled load banks are the best choice for industries and applications with their high efficiency, compact size, quiet operation and precise load testing.
-
Product
Signal Module, ITA, QuadraPaddle, 90 Series, 192 Position, Fully Loaded with Round Posts (610 138 115)
510151107
-
Used together with QP ITA module p/n 510109316 for PCB mounting. NOTE: Mounting screws for this module are included with module part # 510109316. Primary mating module 510150115. (May mate with other Receiver modules, as well.)
-
Product
Light I-V Testing for Solar Cells
FCT-650
-
Advanced analysis of solar cells including light I-V and Suns-Voc data.
-
Product
DC Electronic Load Modules For The N6700 Power System
-
Test devices that store or convert energy by adding a DC electronic load to your Keysight N6700 Series power supply. The Keysight N6790 Series electronic load modules can perform a static or dynamic test and are available in two sizes: single-wide 100 W and double-wide 200 W modules.
-
Product
4 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, SMA, DC Block+200Ω Load 4 Ports
GPS412
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
Product
Programmable Single Channel DC Electronic Load, 150V/30A/300W
T3EL150303P
-
Programmable Single Channel DC Electronic Load, 150V/30A/300W.
-
Product
Electronic Loads
-
Chroma Systems Solutions, Inc.
Power conversion testing for automated test systems, LED drivers, power supply testing, battery testing, and much more.
-
Product
Robotic Sample Loading Systems
-
Below you can see examples of two systems using our robotic sample loading system. Many other automated microscopy systems are possible using our components.
