Optic Amplifiers
Devices that boost light signal in an optical fiber network. The optical signal is amplified directly without need for electrical conversion.
-
Product
Portable Power Amplifier
PAV120Bip
-
PAV120Bip（6*120V） is the portable type power amplifier which is specially designed for R&D of power system simulation. It is with linear type amplifier design so that it could be adapted to simulation experiment which may include various capacitive and inductive load.
-
Product
47~1200MHz FTTH CATV Optic Receiver
H1224
-
Hangzhou Huatai Optic Tech. Co., Ltd.
H1224, the operating bandwidth of 47 ~ 1200MHz, is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver. Products with high sensitivity optical receiver tube and special low noise matching circuit.Receiving at high optical power can be adjusted by PAD level, played limiting output, so H1224 within a large dynamic range of the received optical power of +2 dBm ~-19dBm, have excellent characteristics.
-
Product
Fiber Optic Talk Set
-
Fiber optic talk set consists of both the fiber optic light source and transceivers, which carry voice over the spare fiber in both directions. When doing the test work, technicians may need remote location communication during the measurement or splicing work, and sometimes radio-based communications may not be suitable because of environmental conditions such as FCC restrictions, etc. fiber optic talk set will function well in such cases, they could utilize the already installed fiber optic link to carry voice communications.
-
Product
Optical Link
OPT-2
-
The OPT-2 Optical Link allows the THERMES-USB to be operated with total optical isolation between THERMES and the host computer. USB Isolation device offers up to 4500 volts DC isolation.
-
Product
Optical Communication Analysis
-
In lab and manufacturing environments, R&D engineers require scalable and optimized test solutions to enable them to properly characterize new advanced modulation scheme signals for next-generation, ultra-high-speed telecom networks. Through EXFO’s optical communication analyzers, R&D engineers and manufacturing operations involved in the development or production of transmitters or systems based on new high-speed technology will find the right tools for their advanced technology needs.
-
Product
Optical Power Meter
SAT-7E PON
-
Shaanxi Aitelong Technology Co., Ltd
SAT-7E PON power meter is a special tester to test FTTx/PON passive optical network, it can synchronously measure voice, data and video signal on BPON/EPON/GPON framework. It also can set the power threshold and indicate the pass, alarm and fail of every wavelength.
-
Product
Multi-Functional Optical Profiling system
7505-01
System
Chroma 7505-01 is the newest multi-function optical inspection system that equips with the capability of measuring 1D, 2D and 3D at the same time. Penetrating reflection measurement is used for 1D film thickness measurement to measure the non-destructive film thickness on transparent and translucent material.
-
Product
Isolation Amplifiers
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Unipolar and bipolar DC input signals 20 mV to 200 V and 0.1 mA to 100 mA calibrated range selection. Working voltage up to 1000 V AC / DC.
-
Product
Low Phase Noise Amplifiers
-
Pasternack's low phase noise amplifiers cover select frequency bands ranging from 1.5 to 18 GHz with residual phase noise levels as low as -180 dBc/Hz @ 10 KHz offset. Additional performance specs include small signal gain ranging from 9 to 14 dB, with typical noise figure of 5.5 dB. Psat levels for these amplifiers range from +16 to +25 dBm with Output IP3 levels as high as +34 dBm. All models feature single DC voltage supplies and input/output RF ports are internally matched for 50 ohms with DC blocking capacitors. These compact module assemblies require no external components and are available in rugged Kovar metal drop-in packages that are gold-over-nickel-plated and support field replaceable SMA connectors. All models are EAR99 and guaranteed to meet MIL-STD-883 test conditions for hermeticity and temperature cycle.
-
Product
RF Benchtop / EMC Amplifier
-
RF-Lambda is a world leader in the design and manufacture of high-power, solid-state, broadband AC-powered EMC power amplifiers.
-
Product
Composite 1×24 Video Distribution Amplifier
VDA124RM-12
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Brinell Optical Scope
HiLight Series
-
Newage Testing Instruments, Inc.
The Newage 5620 Series HiLight Brinell Optical Scopes features a high-efficiency LED array for its light source, providing excellent illumination and improved readability over conventional “flash light” scopes.
-
-
Product
Amplifier
-
Toellner Electronic Instrumente GmbH
An electronic device that increases the voltage, current, or power of a signal.
-
Product
Shortwave Power Amplifier
OM4001A
-
The OM Power model OM4001A is designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. It is equipped with a two ceramic tetrodes FU-728F.
-
Product
Power Amplifier For Real-Time Dynamic Simulation(RTDS) Application
-
As the first power amplifier manufacturer in China, PONOVO has been offering various power amplifier products for customers in China and other countries since 2001. PONOVO has launched both conventional power amplifier for power system use and also 4-Quadrant power amplifier for more filed application, such as microgrid, windfarm, PV, HVDC, areospace, battery simulation, etc.
-
Product
Optical Sensors
-
Many measurements are much easier to make with light. Southern Photonics designs and manufactures optical sensor systems for a wide range of applications including gas sensing and strain sensing.
-
Product
Low Noise Amplifiers
-
LNA amplifier PE15A1000 is rated at 13 Volts DC maximum and 200 mA. Our low noise radio frequency LNA amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial millimeter wave low noise amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
Product
Optical Multimeters
-
Optical Multimeter integrates both an optical power meter module and an optical light source module and can perform closed-loop tests by using both modules but work individually. It is specifically designed for technical support personnel to test a variety of instruments with a single meter and thus satisfy the user by providing a choice of greater convenience and more advantages.
-
Product
Optical Power Meter
TL-520
-
TL520 Mini-Designed Optical Power Meter is a self-developed test instrument which is widely used for installation, operation and maintenance of fiber-optic network. TL520 can test optical power within the range of 800~1700nm wave length. There are 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 1625nm, six calibrated wavelength.
-
Product
Carbon-Fiber Reinforced-Polymer Optical Breadboards And Benches
-
Advanced Photonic Sciences LLC
Carbon fiber optical breadboards provide a similar thermal stability to Super Invar but at a lower cost and are inherently non-magnetic. For ages, steel breadboards have been the only choice; however, structures made from carbon fiber reinforced polymer (CFRP) have been used in the aerospace and space industries for many years due to their low weight, high strength, excellent thermal stability and low resonant frequencies. APS now brings this advanced technology to the world of photonics in the United States and Canada with carbon fiber breadboards from CarbonVision. Four grades of carbon fiber breadboard are offered: the economic EC-Series, the advanced AD-Series, the all-carbon AC-Series, and the slim SL-Series.
-
Product
Signal Amplifier
ZET 410
-
The ZET 410 preamplifier is used as a signal amplifier in processing systems and various instruments and actuator control systems. It is used in industry, laboratory and mobile studies.
-
Product
Laser Microdissection and Optical Tweezers
-
Laser Microdissection is the contamination-free method for separating and collecting cells of interest out of tissue samples or cell cultures. The isolated pure cell populations are the ideal starting point for specific and meaningful results in your molecular analysis. Optical Tweezers are also a contact-free method that uses a highly focused laser beam to manipulate and sort cells in suspension, for example bacteria.
-
Product
Optical Components for Custom Spectroscopy
-
HORIBA offers a wide variety of optical accessories. We have optical choppers which pulse continuous light sources. Explore our order sorting filter wheels for spectrographs and monochromators. Choose from our optical fibers and light guides, with flexible light delivery, single fibers, fiber bundles, and liquid light guides. And select from our lens and mirror-based sample compartments.All of these accessories are compatible with our various optical components. Our optical accessories allow us to complete a custom solution for your unique configuration requirements and a variety of spectroscopy applications. HORIBA offers more choices to ensure you can select the best optics for your needs.
-
Product
Fiber Optic Power Meter
-
Fiber optic power meter is a test instrument used for absolute optical fiber power measurement as well as fiber optic loss related measurement .This hand held type fiber optic test equipment features ingenious appearance,wide range of power measurement, high accurate test precision and user automatic self calibration function. Fiber optic power meter is a tool for telecom and CATV network.
-
Product
Optical Variable Attenuator
TW3303
-
Techwin(China) Industry Co., Ltd
The Perfect Handhold Tester Series Optical Variable Attenuator TW3303 TW3303 handhold optical variable attenuator is used for continuously variable optical signal attenuation. As the attenuator is used in the laser system for the on-line testing, there, thereforeTW3303 can be used in the digital system of communication devices (such as: PHD, SDH) and also in the system of adopting analog modulation (CATV
-
Product
LXI Dual 2x2 Optical MUX LC Multi-Mode
60-851-405
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-414-M50
Multiplexer Module
The 40/42-850A-414-M50 is a PXI/PXIe 4-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Beam Directing and Reflecting Optics
-
Beam directing and reflecting optics simply reflect, bend or translate the beam, but do not typically modify the polarization, except for polarizing beam splitters. For example, mirrors, cube corners and retroreflectors are attached to objects that move in order to keep the weight down on the moving object (instead of mounting the interferometer on the moving object).
-
Product
Optical Oxygen Sensors
-
The analyzer is suitable for direct field installation (NEMA 4X) in hazardous area (Class I, Division 2). The optical fiber sensor platform allows small inline sensors to be installed into sample tubing lines (1/4”), flow cells using NPT fittings, or directly into tanks or process lines using our retractable “hot tap” sensor design. BOS optical oxygen sensors are impervious to typical O2 poisons (H2S) and interferences (combustibles, magnetic, CO2 and H2) with high accuracy and long-term stability measurements without the need for complex or advanced sample conditioning systems. The threaded version of the optical sensor has optional Dual Seal (ANSI/ISA 12.27.01) classification for high pressure applications up to 1200 PSIG (82.7 BAR).
