-
Product
High Voltage Test Sets
-
Nmc's high voltage test sets are manufactured as per the customers requirement ranging from 5kv-100kv ac or dc.
-
Product
AC / DC Combined High Voltage Test Set
-
Cambridge Instruments & Engineering Co.
suitable to perform AC High Voltage Power Frequency test on transformers, motors, cables etc. Leakage current can be measured at desired pressure and this set can be used as a source for cable fault burning.
-
Product
Primary & Secondary Current Injection Testing Sets
-
Primary current injection kits are used to test and commission Circuit Breakers, Bus Bars, CTs, Relays, MCCs, PCCs etc. These are also used for high current injection and simultaneously measuring voltage drops and hot spots in bus-bar joints, Circuit Breaker Contacts etc.
-
Product
Coaxial Attenuators Set
11582A
Attenuator
The Keysight 11582A contains a set of four 8491B attenuators 3, 6, 10, and 20 dB furnished in a handsome walnut accessory case. The Keysight 8491B are type-N connectors with a maximum frequency of 18 GHz. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
Replacement Solder Tip Lead Set for D410/D610
Dx10-SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
DC High Voltage Test Set
-
It is extensively used in electrical and power generation industry for varied testing operations.
-
Product
Universal relay test set and commissioning tool
CMC 356
-
The CMC 356 is the universal solution for testing all generations and types of protection relays. Its powerful six current sources (three-phase mode: up to 64 A / 860 VA per channel) with a great dynamic range, make the unit capable of testing even high-burden electromechanical relays with very high power demands.
-
Product
Test Port Adapter Set, 2.4 Mm To 2.4 Mm
85130G
Test Port Adapter
The Keysight 85130G test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a NMD-2.4 mm (f) to NMD-2.4 mm (m) adapter and a NMD-2.4 mm (f) to PSC-2.4 mm (f) adapter. The frequency range for these adapters is dc to 50 GHz with a return loss of 23 dB or better.
-
Product
Replacement 30" Matched Cable Set for Use with Dx10 HiTemp Solder Tip Leadset
Dx20-Cable-HiTemp
-
Replacement 30" matched cable set for use with Dx20 HiTemp Solder tip leadset
-
Product
Manually Operated Transformer Oil Test Set
-
We offer Manually operated Transformer Oil Testing Kits to check the DI-electric strength of the insulating Oils as per relevant specifications via. IS 6972. It is a useful equipment for transformer / switchgear manufacturing units. Oil frittering agencies, repair shop and electrical maintenance departments.
-
Product
Ionization Test Set
PFK-105
-
- Ionization Test Kit for Measuring Offset Voltage and Discharge Times- Includes a Field Meter, Charge Plate Monitor, ±1000 Volt Charger and Decay Timer- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Evaluate Ionizers and Packaging Materials- Includes a fixture to hold the PFM-711B, CPM-720B and PDT-740B as one- Molded Carrying Case with Foam Insert Included
-
Product
Semi-Rigid Cable Set, 3.5 Mm (Test Port) To 3.5 Mm
85131D
Test Port Cable
The Keysight 85131D is an 53 cm (21 in) long1 semi-rigid cable set composed of a 3.5 mm female2 to PSC-3.5 mm female connector and a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt(f) + 0.2 dB, where f is frequency in GHz, for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability1 of the Keysight 85131D is less than 0.06 dB and phase is 0.16 * f + 0.5, where f is frequency in GHz.
-
Product
Test Lead Set
131139
-
IEC 1010 Rating: 1000 Volts Cat III Double/Reinforced Insulation 20Amps. Kit Comprises:- 1 Pair 123856/OF-OR/1.2 Double Insulated Silicone Lead Assemblies. 1 Pair 121017 Test Prods. 1 Pair 121026 Sprung Hooks. 1 Pair 126024 Fully Insulated Crocodile Clips. Packed In Silver Wallet.
-
Product
6 MHz Level Test Set ET 92
ET 92
-
100 Hz to 6 MHz selective/wideband Level Meter & Generator, with Spectrum Analyser
-
Product
Forward Path NPRT 2200 Noise Power Ratio Test Set
NPRT 2200-F
-
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
Product
Oil Test Set
-
RR-OIL TEST SET also known as OIL BDV KIT is an equipment-designed and produced to test the ELECTRICAL STREGTH of Liquid Insulating Materials such as Transformer Oil, Capacitor Oil etc. The test set carries out test on these materials as per Indian Standard Specification IS 6792. This Oil Test Set is essential for Transformer & Switchgear Manufacturers, also for oil filtration units.
-
Product
Test Port Adapter Set, 1.85 Mm To 1.85 Mm
85130H
Test Port Adapter
The Keysight 85130H test port adapter protects the test set port from being directly connected to the device under test. This adapter has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 1.85 mm to 1.85 mm male adapter and a 1.85 mm to 1.85 mm female adapter. The frequency range for these adapters is dc to 67 GHz with a return loss of 23 dB or better.
-
Product
OPTICAL LOSS TEST SET (OLTS) MQJ KIT
4000-1025
-
The OLTS (Optical Loss Test Set) - MQJ Kit includes a soft, padded carrying case with strap that is provided to protect all of the components during transportation and/or storage.
-
Product
Automatic Relay Test Set
MT2000 Series
-
Portable single phase dual current manual and automatic relay test set. Readymade test modules. Independent control of Phase angle, frequency and amplitude.
-
Product
Kelvin Clip Test Lead Set
5940
-
Kelvin Clip Test Lead Set. Ideal for resistant measurementsbelow 1 ohm.
-
Product
Partial Discharge Test Set Up
-
This testing set is of great use in industries for various testing applications. We strictly follow all the guidelines while manufacturing this Partial Discharge Test Set Up.
-
Product
Protection Test Set
COMPANO 100
-
COMPANO 100 is the universal and easy-to-use solution for all types of basic testing duties in electrical energy systems. Controlled electronic sources allow the user to obtain exactly the desired value and to output signals with variable frequencies and other signal forms, automated ramps, and pure DC.
-
Product
Earth Bond Test Set
EC-12
-
The Earth bond test is a basic safety test prescribed in many standards to test samples for the integrity of earthing continuity throughout the sample.
-
Product
Secondary Injection Test Set
PTE-100-C
-
The PTE-100-C is a portable Universal test equipment for testing electromechanical, electronic, and digital relays. The equipment can output a variable current up to 250A, a variable AC Voltage up to 250V, a variable DC Voltage up to 350V. Also the unit incorporates a variable stabilized auxiliary DC Voltage supply up to 250V and a fixed AC Voltage output up to 110V, which can be variable with the PTE-FCF option.
-
Product
Large Current 1000A Primary Current Injection Test Set
TEST-901
-
Beijing GFUVE Electronics Co.,Ltd.
TEST-901 primary current injection test set adopts ARM Chip to control its output process and large capacity of toroidal transformers. It is equipped with LCD display and current meter; it can show primary current value, second current value, turn ratio and the action time. Packing is used as aluminum alloy body with PC panel. TEST-901 is mainly applied to CT turn ratio testing in the power system and contact resistance test which need large current.
-
Product
Telecom Audio Test Sets
-
Networked Communication Solutions, LLC
Handheld test instruments for complete troubleshooting of audio frequency impairments on communication networks.
-
Product
Repeated Charge Discharge Test Set
-
The IS 13341 : 1992 has laid down the requirements for Ageing Test, Self-Healing Test and Destruction Test on Shunt Capacitors of the self healing type for AC Power Systems. The Ageing Test is to be performed at a specified voltage of 1.25 times the rated voltage for 750 hours. The test is to be followed with a repeated discharge cycle test which involves charging of the capacitor to a DC voltage and discharge of the same through an Inductance. Sivananda Electronics has developed this equipment for the benefit of capacitor manufacturers, for the first time in India.
-
Product
Test Set For Instrument Transformer
-
This modern Test Set For Instrument Transformer is used for measuring relative errors of Instrument Voltage and Current Transformers. This is developed for reading out the unbalance of any bridge circuit. It also calculates the burden associated to the test sample. In addition to this, it further converts it to ratio and phase error values for presenting them on a LCD screen. With high-tech microprocessor controller, it ensures to provide quick and correct measurements.
-
Product
Ramp or Flight line Air Data Tet Sets
-
The test sets are all digitally controlled through a local or remote keypad and display. The intuitive user interface allows test set functions to be easily controlled with a minimum of key strokes, with all test parameters displayed, and is suitable for both first time and more advanced users. Optionally many of the ADTS can be remotely controlled by a PDA Pocket PC with wireless Bluetooth connection. The intelligent user interface provides protection to both the test set and the UUT. The software rejects entered command values that exceed the pre-selected limit ranges.
-
Product
High Pressure/Low Set Point Pressure Switch
J205G
-
The J205G High Pressure Low Set Point Pressure Switches are among our most versatile offering, affording the end user an extensive operating environment and a wide range of set point optionality.
