Digital I/O
Input/output of digital values.
-
Product
PCI-6511, 64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated Digital I/O Device
778966-01
Digital I/O
The PCI-6511 is an industrial digital input interface, with eight banks of isolated channels. If a computer or application fault occurs, the PCI-6511 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Bi-Directional Differential-TTL I/O PXI Card
GX5641 Series
Digital I/O
The GX5641 is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), functional test, and factory automation applications. The GX5641 consists of 64 bi-directional TTL-differential I/O channels. Each channel has two ports (TTL and differential) which can be individually set to operate in either conversion or static I/O modes.
-
Product
PXIe-6569, PXI FlexRIO Digital I/O Module
787283-01
Digital I/O
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
Product
NI-6584, 16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
781290-01
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter
-
Product
10-CH General-Purpose Timers/Counters & 8-CH Digital I/O Card
PCI-8554
Digital I/O
- Supports a 32-bit 5 V PCI bus- On-board four 82C54 programmable timer/counter chips- 10-CH independent 16-bit down counters- 1-CH 32-bit cascaded timer- Four programmable clock sources for each timer/counter
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24V +special EEPROM & TTL IO Port
APCI-1500-PULS
-
PCI interface to the 32-bit data bus Connector compatible to PA 1500 Connector and software compatible to CPCI-1500 16 isolated input channels, 24 V, including 14 interruptible 3 software-programmable counters/ timers 16 isolated output channels, 10 to 36 V, output current 500 mA Timer-programmable watchdog for the reset of the outputs"-PULS" version has a special EEPROM and a TTL IO port added at end of cardDiagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdog Interrupt triggered through watchdog, timer, error One ground line for all inputs and one ground line for all outputs
-
Product
Keysight 64-bit Digital I/O with Memory and Counter for 34980A
34950A
Digital I/O
The Keysight 34950A module for the 34980A Multifunction Switch/Measure Unit has 64 bi-directional lines configured as eight 8-bit channels. Each 8-bit channel has programmable polarity and thresholds up to 5V. The memory is useful for simulating and capturing digital patterns up to 10 MHz. It provides configurable handshaking protocols for a wide variety of applications.
-
Product
PCI-7811, 1M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779363-01
Digital I/O
The PCI‑7811 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7811 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24V, LACQUERED
APCI-1500-LAC
-
PCI interface to the 32-bit data busConnector compatible to PA 1500Connector and software compatible to CPCI-150016 isolated input channels, 24 V, including 14 interruptible3 software-programmable counters/ timers16 isolated output channels, 10 to 36 V, output current 500 mATimer-programmable watchdog for the reset of the outputs to ??Diagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdogInterrupt triggered through watchdog, timer, errorOne ground line for all inputs and one ground line for all outputs
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5290 Series
Digital I/O
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
Ribbon cable between digital I/O of CPCI-3xxx & D37 connector on 3U cPCI bracket
FB3001
-
Ribbon cable between digital I/O channels on CPCI-3xxx boards & D37 connector on 3U cPCI bracket.
-
Product
FPGA with Digital I/O PCIe Mini Card
TMPE633
-
The TMPE633-10R provides 26 ESD-protected 5V-tolerant TTL lines, the TMPE633-11R provides 13 differential I/O lines using EIA 422 / EIA 485 compatible, ESD-protected line transceivers and the TMPE633-12R provides 13 differential I/O lines using Multipoint-LVDS Transceiver.
-
Product
48 Optocoupled Open Drain 42V 6A Digital Outputs
YAV90048
Digital I/O
6×8 Isolated Ouput Banks Trigger IN and OUT Termic and Overcurrent protection CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
Product
Digital I/O - USB
-
External, hot-pluggable modules that allow computers to monitor (input) and control (output) binary signals (\(0/1\), High/Low) via a USB port.
-
Product
Reconfigurable FPGA w/ AD/DA & Digital I/O PCIe Mini Card
TMPE627
-
The TMPE627 is a standard full PCI Express Mini Card, providing a user programmable Xilinx Artix-7 7A50T FPGA. The TMPE627 provides 14 ESD-protected 5 V-tolerant TTL lines. All I/O lines are individually programmable as input or output. TTL I/O lines can be set to high, low, or tristate. Each TTL I/O line has a pull-resistor to a common programmable pull-up voltage that can be set so +3.3 V, +5 V and GND.
-
Product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 8 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
CPCI-3120-8-8
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
Digital I/O Board w/CoS IRQ
104-DIO-48S
-
*48 or 24 parallel lines of 82C55 digital I/O with tristate buffers prevent unintended control of external equipment*IRQ on input change of state (COS) eliminates the need for constant polling*High sink/source current 64mA/32mA*I/O pulled up to 5V for contact monitoring*Compatible with Opto-22 and other industry standard I/O racks
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5050
Digital I/O
The GX5050 is a high speed Dynamic Digital I/O card that provides a full set of features that is comparable to high speed I/O products found in large functional test systems. The card shares an identical architecture with the GC5050, but the GX5050 is a PXI card (6U) and the GC5050 is a PCI card. Both have the ability to operate independently of the host computer when in RUN mode.
-
Product
Industry Pack Carriers and Digital I/O
CPCI-4SIP-6U
Digital I/O
The CPCI-4SIP-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4SIP-6U is the perfect solution. There are four (4) Industry Pack sites providing up to 200 I/O pins accessible from either the front panel or the rear back plane.
-
Product
PXIe-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module
787358-01
Digital I/O
PXIe, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module - The PXIe-6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each line for input or output and you also can configure each line with a user-configurable pull-up or pull-down resistor. Using the PXIe-6509 programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. The PXIe-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. The PXIe-6509 provides programmable input filters for eliminating glitches or spikes and for debouncing digital switches or relays through a software-selectable digital filter.
-
Product
32 Input, 32 Output USB Modular Digital I/O
U2651A
Digital I/O
The Keysight U2651A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
PCI Digital I/O Cards
-
Sealevel PCI digital I/O cards are available with optically isolated inputs and Reed relay outputs. For high-voltage requirements, TTL versions provide convenient connections to industry-standard solid-state relay racks. Sealevel low profile PCI digital I/O boards meet the requirement for the MD1 low profile specification and feature Universal Bus (3.3V and 5V) for compatibility with both new and legacy computer systems.
-
Product
LVDS Digital I/O with Virtex-6 FPGA - 3U VPX
Model 52610
-
- 32 bits of LVDS digital I/O- One LVDS clock- One LVDS data valid- One LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAs- DMA controller moves data to and from system memory- Up to 2 GB of DDR3 SDRAM- PCI Express Interface- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
Product
16-Bit Multi-Function With A/D, D/A And Digital I/O Channels CPCI Cards
GX3232 Series
cPCI Card
The GX3232 is a multi-channel 16-bit, analog input and output cPCI module, supporting 32 single-ended or 16 differential input channels and four analog output channels. The inputs can be software configured for differential or single-end operation and are sequentially scanned with a maximum aggregate scan rate of 300 kS/s. Three input ranges are software-selectable: ±10 V, ±5 V or ±2.5 V. Optionally, the GX3232 is available with a high voltage input configuration and supports three ranges: ±60 V, ±30 V and ±15 V. The high voltage configuration supports 16 single-ended or 8 differential input channels for high voltage and 16 single-ended or 8 differential inputs for low voltage measurement. Four analog output channels provide software-selectable output ranges of ±2.5 V, ±5 V or ±10 V. The outputs can be updated either synchronously or asynchronously and support waveform generation. Each output can be clocked at rates up to 300 kS/s. A 16-bit digital I/O port is also provided, which supports 16 bidirectional data lines. Note that when used with a TS-700 system only 8 of these digital I/O lines are available at the test system's receiver interface.
-
Product
Digital I/O
-
Curtiss-Wright Defense Solutions
Curtiss-Wright Digitial I/O cards include interfaces to LVDS, Camera Link, Serial intrefaces, CANbus and customizable I/O. With over 20 years experience in the design and production of top quality COTS signal acquisition hardware, we deilver PMC, XMC and PC/104 modules that can cope with the toughest operating environments.
-
Product
LVDS Digital I/O with Virtex-6 FPGA - 6U VPX
Model 57610
-
- 32 or 64 bits of LVDS digital I/O- One or two LVDS clocks- One or two LVDS data valid- One or two LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAS- One or two DMA controllers move data to and from system memory- Up to 2 or 4 GB of DDR3- PCI Express (Gen. 1 & 2) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- Ruggedized and conduction-cooled versions available
-
Product
Digital I/O Module with 32 24V inputs
IO206
-
This I/O module is a dedicated digital I/O module providing 32 channels of 24V inputs. The inputs are galvanically isolated by opto-couplers. All channels have a common freely programmable debounce time. Each IO206 I/O module comes with xPC Target driver blocks and Simulink test models, an external shielded 50-pin I/O cable and a terminal board for easy access of all physical I/O signals, and comprehensive documentation.
-
Product
96-Channel Digital I/O Plug-In
1260-114
Digital I/O Board
The high channel count of the digital I/O plug-ins allows a significant portion of digital I/O to be realized in a single slot of the Adapt-a-Switch™ carrier, saving valuable VXIbus chassis space. The 1260- 114 provides 96 digital I/O channels in twelve groups of eight bits each.
-
Product
Dynamic Digital I/O (3U), 32 Channels Up To 200 MHz W/512MB On-Board Memory, W/LVDS
GX5283
Digital I/O
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
Multifunctional Digital Design Core
PA72DIOS6016
Digital I/O
The PA72DIOS6016 is a multifunctional digital design core. The FPGA allows for implementing many different custom applications. The connector has 64 Input/Output pins which can be assigned as TTL I/O or as differential inputs. 128 MByte of DDR2 memory is available to the FPGA, and an onboard EEPROM allows for storing values in non-volatile memory. The I/O bank voltage can be FPGA-selected between 2.5 and 3.3 Volt.
