Magnetic Field
an force around magnets, electric current and atomic orbits.
See Also: Magnetic, Magnetic Test, Magnetic Head, Magnetic Susceptibility, Magnetic Flux, Magnetic Stripe, Magnetic Permeability, H-field, Magnetic Field Mapping, Magnetic Field Meters, Magnetic Field Probes, Magnetic Field Sensors, Magnetic Field Test, Helmholtz Coils
-
Product
Digital Power Transducer
LP Series
-
*High accuracy 0.07% rd + 0.03% ro*Excellent long term stability*Outstanding over capability and temperature performance*Wide selection of input / output ranges*Meets ANSI C37.90 (1989) and BEAMA No. 219 tests*High magnetic field immunity*Real power - able to measure distorted waveform
-
Product
Sensor Node
Smart Parking
-
Libelium Comunicaciones Distribuidas S.L
The main method is magnetic detection: a 3-axis magnetic sensor reads the variations in the Earth's magnetic field. The big mass of metal of a car parked on the slot changes this field and the node will know. The software inside the node implements advanced algorithms to dynamically compensate the temperature variations and also the influence of neighbor cars.
-
Product
Tesla Meter
GX-100/GX-200
-
It can measure tiny magnetic field from 0.01mT. Both AC and DC can be measured without select.
-
Product
Reference Magnet
-
Reference magnets generate a homogeneous magnetic field in an air gap. They are mainly used to calibrate hall probes for their full scale value of output for the magnetic field strength H or the magnetic flux density B they measure. For example Gaussmeters can be calibrated by using reference magnets.
-
Product
Railway and Traffic Engineering Solutions
-
In the past, LXinstruments has already implemented a number of application-specific system solutions which cater for these special requirements. These solutions are often used to replace systems which have been in production for many decades. Our systems are not only employed for testing signal box technology modules, but also for testing train control system which are installed in the track bed. Due to the strong magnetic fields which occur at the DUT in combination with high voltages, the test systems require specific technical safeguards.
-
Product
TMR Angle Sensors
-
MultiDimension Technology Co.,Ltd.
Angle sensor are proportional to the sine and cosine of the angle of a magnetic field applied parallel to the surface of the sensor, which can be provided by a small magnet positioned above the device.
-
Product
USB Magnetometer
-
MultiDimension Technology Co.,Ltd.
A three-axis digital magnetometer that is intended for the measurement of magnetic fields near the probe tip at frequencies less than 250 Hz.
-
Product
Neutron Scattering and Beamline Systems
-
For optical, neutron and particle beam experiments, Cryogenic offers a range of split pair magnets. These allow strong magnetic fields to be produced in a small volume with maximum access to the working space. Split pair coils can be mounted to provide either a vertical field with horizontal access or a horizontal field offering horizontal or vertical access.
-
Product
Loop Antennas
-
A.H. Systems' designs, manufactures and delivers high performance Loop Antennas for a wide range of magnetic field testing. Whether used in a set to measure shielding effectiveness per MIL-STD 285 and NSA 65-6 or individually to satisfy specific requirements,
-
Product
Fault Passage Indicator for Lines
LineTroll R400D
-
LineTroll R400D Fault Indicator indicates earth- and short-circuit faults and can distinguish between permanent and transient faults. The indicator has two sensors and use both the electrical field and the magnetical field to detect faults on all three phases.
-
Product
Magnetic Field Tester
Rotor-Check 400
-
Rotor-Check 400 is a practical testing device used to check the magnetic field strength curve of a rotor. The device and measuring probe connect directly to a Windows PC via USB. It is an ideal solution for precise magnetic field measurement and analysis.
-
Product
H/E fieldmeter
ESM-100
-
The 3D H/E fieldmeter ESM-100 is a patented, unique hand held measuring instrument. It can easily measure electric and magnetic alternating fields simultaneously, independent of their direction, and at one point. With this piece of equipment it is possible for anybody, to carry out quick, professional and error-free measurements, right from the beginning
-
Product
Sport Sensor Range
-
DHE (Differential Hall Effect) sensors give an output when subjected to a changing magnetic field. The field is set up by a magnet inside the sensor body and changes when ferromagnetic teeth are passed beneath the sensor (no magnets are required in the target). To improve noise resistance, the sensor has two Hall effect elements and only responds to changes in magnetic field strength corresponding to tooth passing frequencies above 15Hz. As each tooth passes the sensor, the digital state of the output changes
-
Product
Magnetic Transducers With Hybrid 1-/ 2-/ 3-Axis Hall Probe Sensors
H3B
-
The **H3B Magnetic Transducer** is an advanced Low Noise SENIS device designed for measuring magnetic fields through its hybrid three-axis Hall Probe. With a remarkable capacity for ultra-low noise, it effectively minimizes offset fluctuations, ensuring precision in magnetic field measurements. This robust transducer is tailored for applications that demand high accuracy and stability, integrating three high-resolution Hall sensors with an orthogonality error of less than 2°. Additionally, a built-in temperature sensor provides real-time temperature compensation, enhancing measurement reliability across various conditions.Beyond its noise reduction capabilities, the H3B transducer delivers a comprehensive output of three differential voltages corresponding to the magnetic flux density components (Bx, By, Bz) and a ground-referred voltage signaling the Hall sensor's local temperature. The system's innovative spinning-current technique significantly reduces low-frequency noise while maintaining excellent linearity, making it a valuable instrument for mapping magnetic fields, characterizing undulator systems, and performing quality control in laboratory and industrial settings.
-
Product
Zero Gauss Chamber
-
Measuring station for reproducible and location-independent measuring results for quality assurance, eg B. for cross-company supply chainsMeasurements of residual magnetism on ferromagnetic components are no longer significantly falsified by ambient magnetic fields induced in the object passive shielding, no power consumption and maintenance-free defined measuring station, good measuring room accessibility Platform in a robust design
-
Product
4 Port Devices
-
Four port devices can be realized by joining two 3 port devices via the appropriate ports. As system performance requirements become more demanding, new design approaches must be adopted. These include Faraday rotation devices and phase shift circulators. The bandwidth and isolation limitations of 3 port devices are overcome through a distributed architecture that enables more ferrite material to be incorporated into the transmission path, thereby achieving an increase in the biasing magnetic field. Phase shift circulators can be designed to handle higher RF power than 3-port devices.
-
Product
Vibrating Sample Magnetometer
VSM-P2H
-
This is low magnetic field type of exclusive use for soft thin film sample by the use of Helmholtz Coil.The type is capable of measuring variations of temperature from -50°C to 200°C by adding gas-flow type of temperature controller as an option.
-
Product
Pocket Fieldmeter
FM10
-
The field strength measurement device with innovative technique and revolutionary design in shirt-pocket format. Simultaneous display of the electric and the magnetic field strength Isotropic measurement of alternating fields. Potential-free and potential-related measurement of electric fields. Frequency range from 10 Hz up to 400 kHz
-
Product
Vehicle Actuator Tester
7651
-
Peaceful Thriving Enterprise Co Ltd
This device is design to test electronic components actuate by magnetic field or electronic magnetic field. Devices like actuator, ignition coil, AC generator, indoor air blower, valve controller EGR (exhaust gas control), injector, spark plug, relay and hall effect sensor can be tested.
-
Product
Space-Magnetic Field Visualization System
EPS-02EMF System
-
The system detects position of the magnetic field sensor on thebasis of the image on the camera first of all and then, recognizes strength of the signal that is measured by the sensor upon frequency analysis of the signal almost simultaneously. Finally, visualization of the strength dispersion in composition with the real image of the measured object can be realized on screen of PC.
-
Product
Calibration Cube / Reference Magnet
-
The SENIS Calibration Cube is an indispensable tool for the precise calibration of magnetic field sensors and mapping equipment. With a homogenous magnetic field accessible through six strategically placed holes in the cube's faces, users can easily place sensors from various sides to calibrate their sensitivity vectors accurately. This makes it an ideal solution for in-situ validation, ensuring reliability and accuracy in the user's environment. The calibration tool not only simplifies the calibration process with its intuitive software guidance, leading to the creation of a sensitivity matrix, but it also defines mechanical referencing with an orthogonality better than 0.1° across all three directions. In addition to its effective calibration capabilities, the SENIS Calibration Cube serves as a stable reference magnet, enhancing the user experience. The cube requires less than 30 minutes for full high-accuracy orthogonality recalibration, making it efficient for routine sensor changes on mappers. The included Calibration Cube Corner Tool further aids in ensuring accurate orientation to external Cartesian coordinate systems, solidifying its role in achieving the highest mechanical accuracy in magnetic sensor applications. Coupled with its dust-free surface for easy cleaning, the SENIS Calibration Cube stands as a reliable and high-performance calibration instrument.
-
Product
Teslameter
RX - 32
-
The device is designed to work as a research or service instrument characterized by a very high precision of magnetic field measurement. Thanks to the operation based on the principle of nuclear magnetic resonance ( Nuclear Magnetic Resonance - NMR ), it is a quantum device whose indications do not depend on external factors such as temperature, pressure, aging effects, etc.
-
Product
Passive Magnetic Antennas, TX-Loop Antennas
-
A passive loop antenna which is matched to a resonance frequency of 13.56 MHz with 370 kHz bandwidth (-3dB)The purpose of the antenna is to produce defined magnetic fields at 13.56 MHz efficiently, i.e. to test near field communication devices (NFC) or RFID equipment.
-
Product
3-Axis Hall Probe A
-
The Hall Probe A for F1A Magnetic Transducers is a highly advanced, robust solution designed for precise measurement in magnetic field applications. With dimensions of 16.5 mm in length, 5.0 mm in width, and a thickness of 2.3 mm, this single-chip, fully integrated 1-axis Hall probe excels in providing accurate readings of magnetic fields perpendicular to the probe plane. Utilizing a CMOS integrated circuit, it incorporates four Hall elements, biasing circuits, amplifiers, and a temperature sensor, which enhances its versatility and reliability in various environments.The Hall Probe features a remarkable spatial resolution of 0.4 x 0.01 x 0.04 mm, thanks to the compact size of the integrated Hall elements. It employs a unique spinning-current technique that effectively suppresses the planar Hall effect, achieving an extensive frequency bandwidth of DC to 75 kHz. This ensures that the output signals are not only stable but also highly responsive, making it an ideal choice for scenarios requiring rigorous magnetic field analysis. Furthermore, the integrated temperature sensor provides compensation, ensuring that performance remains consistent across different thermal conditions. The Hall Probe A is suitable for use as a Y-axis Hall probe and is available separately for OEM customers.
-
Product
Vector Magnetometer
FVM400
-
Macintyre Electronic Design Associa
The FVM400 uses fluxgate technology to measure the three vector components of the magnetic field. The fluxgate sensors are packaged in a 1" square by 4" long probe that is connected to the handheld electronics unit by a modular telephone cord. The sensor can be located up to 100 feet from the electronics unit.
-
Product
e-Compases
-
Designed to accurately detect the direction and magnitude of external magnetic fields, ST’s eCompasses use accelerometer measurements for tilt compensation, thus ensuring very accurate compass headings even when handheld or mobile devices are inclined.
-
Product
SQUID Magnetometer
-
An extremely sensitive instrument used to measure tiny magnetic fields.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-18S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Ultra compact size with 18mmφ jaw opening capability.*High sensitivity and least affection from external magnetic field.
-
Product
3-Axis Sliding Hall Probe SHP For In-Contact Measurements
-
The 3-axis Sliding Hall Probe SHP is expertly designed for in-contact measurements, ensuring precision with an incredibly small distance of just 0.5 mm between the magnet surface and the Hall probe's sensitive spot. This unique design maintains a constant measurement distance, enabling reliable in-contact magnetic field readings. Incapsulated in a SENIS KS Hall probe and housed in a robust ceramic package, the probe's dimensions are compact at 25x3x3 mm, making it suitable for a variety of applications requiring accuracy in magnetic measurements.In addition to its compact size, the SHP features a ceramic friction pad that enhances its capability for direct contact measurements. This makes it ideal for use in SENIS Mappers or as a customizable component in customer-specific mapping solutions. The precise engineering behind this Hall Probe ensures that it meets high-performance standards in both industrial and research settings, providing vital data for magnetic field analysis.
-
Product
MagTest System
-
A System to generate magnetic fields and to perform tests regarding the susceptibility against magnetic fields.
