TTL
Transistor–transistor logic.
-
Product
USB to TTL Adapter
SKU-012-0X
-
The USB to TTL adapter connects the Serial UART to the standard USB port for testing and monitoring functionality. The Adapter facilitates ease of use and helps to reduce board space and cost.
-
Product
2 To 18 GHz 6 Channel Downconverter
-
Teledyne RF & Micrrowave's Six Channel 2 - 18 GHz (RF and LO) downconverter operates with an IF of ~960 MHz, providing 25 dB of RF-IF gain, and bandwidth of ~500 MHz. This downconverter operates on a single LO at -6 dBm which is amplified, split, then again amplified to each of the 6 channels. Integrated into each channel is a range extension switch, controlled by a TTL input and adding 20 dB attenuation. Noise figure is ~ 13.5 dB and output IP3 is ~+25 dBm. The downconverter is 2- sided, hermetically sealed and designed for rugged applications.
-
Product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
-
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
-
Product
NI-6581B, 100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO
783887-01
Digital I/O Adapter
100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO—The NI-6581B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581B can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
SP16T RF Pin Diode Switches To 10 GHz
-
Pulsar Microwave's 16-way switches cover 500 MHz to 10 GHz in single pole, 16-throw configuration. Maximum input power is 200 mW and switching time is 100 ns. SMA female connectors are standard. A 15-pin D-SUB male connector makes the internal connections to the power, ground and logic circuitry. Switching control is TTL with the option of line drivers and decoders.
-
Product
Serial to Relay Interface Boards
Model 2364 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Serial interface header includes RS-232 and RS-485 signals. * GPIB interface header includes GPIB address switch input signals.* Includes 50-pin mating relay connector and serial header connector.* Optional 115750 Terminal Board for easy connections without soldering.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel.
-
Product
1 Channel 100 MHz Flash ADC
NIMbox DNAE
-
NIMbox DNAE - 1 channel 100 MHz flash ADC with 3 programmable TTL I/O ports, 2 channel DAC 100 MHz, 4 LE discriminators and 5 NIM or TTL I/O
-
Product
High Speed Digital Analog
ITA
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
Product
24-Ch Digital I/O Universal PCI Card
PCI-1737U
PCI Card
ISA-Compatible with PCL-72424 TTL digital I/O channelsEmulates mode 0 of 8255 PPIInterrupt handlingOpto-22 compatible 50-pin connectorsOutput status readbackPCI universal card
-
Product
AMD LX PC/104 CPU Module With VGA/TTL, USB DoM And PC/104-Plus Expansion
AX12260
-
The ultra low power consumption PC/104+ embedded CPU board, the AX12260, is an entry-level core engine with integrated graphics, standalone capability and flexible I/O options that developers require. With its PC/104+ interface, the AX12260 provides the use of a high speed PCI bus (32-bit) in most embedded applications. By built-in AMX LX800 core logic controller with integrated graphics and inherent ruggedness, it also provides a high reliability environment for users.
-
Product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
782401-01
Digital Module
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
Digital I/O
Digital I/O Module
ADLINK digital I/O cards feature TTL I/O, isolated I/O, relay output, and timer/counter, and supports up to 256-CH high-density on a single board, making them suitable for I/O status monitoring and ON/OFF control applications.
-
Product
IC-3173, 2.20 GHz Intel Core i7 Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
784227-01
Controller
The IC‑3173 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3173 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
Product
Dynamically Controlled, High Speed Digital I/O PXI Express Card
GX5292e
Digital I/O Module
The GX5292e is a high performance, cost-effective 3U PXI Express dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5292e also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 100 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
6U CPCI Multifunction I/O Board
78C1
Multifunction I/O
The 78C1 is a universal 6U cPCI Multifunction I/O Board that eliminates the complexity and size constraints of using multiple, independent, single-function cards. This single slot card has six module positions, allowing developers to achieve a custom configuration with any combination of function modules, such as A/D (10-channels), D/A (10-channels), Discrete I/O (16-channels), TTL I/O (16-channels), Differential Multi-Mode Transceivers (11-channels), RTD (6-channels), Synchro/Resolver (4-channels), LVDT/RVDT (4-channels), and Signal Generator (4-channels).
-
Product
128 Channel Digital I/O With 6 Channel Counter
DP-cPCI-3015
-
DP-cPCI-3015 is a 128 channel TTL compatible Digital Input / Output card with 6 counter channels. The DIO can be programmed as input or output in groups of 16 channels.
-
Product
PXI/PXIe Trigger-Module
PXT(e)1741
Trigger Module
Easy linkage of various external modules to the PXI(e) trigger busHigh configurable trigger matrix12 independent configurable trigger linesInputs/Outputs compatible with 5 V TTL standardSoftware controlled triggering of any target device
-
Product
SP5T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
Product
1208/9a Optical Distribution, RX/TX
-
Precise Time and Frequency, Inc.
The ptf 1208A (transmitter) and ptf 1209A (receiver) provide a convenient and simple way to transmit high quality RF signals over long distances, without the concerns associated with electrical interference and pick-up.The ptf 1208A accepts an RF input in the range from 1kHz up to greater than 10MHz and provides a combination of 8 local, high isolation, RF distribution outputs and 4 optical transmission outputs for distances up to 2 kilometers.The ptf 1209A accepts an optical input (transmitted from the ptf 1208A) and provides 12 local RF outputs, either digital (TTL into 50 ohms) or low noise sine wave signals driving 1V rms into 50 ohms (with the PLL option), or both.These systems are especially designed to accommodate IRIG B DCLS, 1PPS and other RF signals in the range from 1kHz to 20MHz.The modular construction allows for a variety of input/output configurations to provide a fully tailored application solution.
-
Product
RS232 RS485 RS422 Serial To Ethernet Modbus Converters / Device Servers
-
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and flexibility. CommFront offers a range of industry-proven, easy-to-use serial to Ethernet converters and device servers, both hardware and software types. The applications of our serial to Ethernet converters include acting as a device server or a Modbus RTU/ASCII to Modbus TCP protocol converter; extending serial ( RS232 / RS485 / RS422 / TTL) communication distance over Ethernet network; controlling serial devices from remote Modbus TCP software or Modbus RTU master via Ethernet network; making a wide variety of M2M communication applications possible by enabling client access independent of any operating system or proprietary protocol; and converting conventional serial data network into TCP/IP network, etc.
-
Product
sbRIO-9403, Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780539-01
Digital Module
Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The sbRIO‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9403 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and other applications.
-
Product
100-Watt DC/DC Converter
55LS1
DC Converter
NAI’s 55LS1 is a COTS, 100 Watt DC/DC Converter that accepts a +28 VDC input and provides a single full-power output at a baseplate temperature of +100° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
Product
56 Channel TTL I/O FPGA PXI Card
GX3756 Series
FPGA PXI Card
The GX3756 is a user configurable, FPGA-based, 3U PXI card which offers 56, TTL I/O signals. The module consists of a daughter card and the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA.
-
Product
IC-3171, 1.9 GHz Intel Celeron Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
784964-01
Controller
The IC‑3171 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3171 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
Product
Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces
M4KDiscrete Module
-
The M4KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M4KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports twenty programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each. Ordering Information:The user can set each discrete:• Either as input or output.• Either to TTL (0 – 5V) or Avionics (0 – 32V) voltage levels on inputs and• Either enable or disable external debounce on inputsThere is a 4092 Word FIFO (a string of 1023 discrete entries) containing the data and time tags.The M4KDiscrete module is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
High-Capacity Compact Real-Time System
ADwin-Gold II
-
10 times more computing power than ADwin-Gold with the processor ADSP TS101S at 300 MHzMore memory: 768 kB CPU-internal RAM, 256 MB DRAMHigher resolution: 2 18 bit ADC with 8 analog inputs each via multiplexerFIFO memory at the digital inputs for fast detection of rising and falling edges with 100 MHz event counter2 analog outputs, 16 bit, 32 digital I/Os (TTL)
-
Product
SP8T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave manufactures 8-way absorptive and reflective RF switches in single-pole 8-throw configuration. They fulfill broadband and narrowband requirements from 40 MHz to 12 GHz and handle 200 milliwatts input power. The SP8T switches have an isolation of 60 dB and switching time of 100 ns. Most models specify 1.6:1 or better VSWR at all ports. The SP8T switches operate on a power supply of +/- 5VDC and switching control is 0-5 TTL logic. The unit comes standard with SMA female connectors. Options for control are line drivers and decoders.
-
Product
Chassis - Controls up to 16 8x1 Modules, 32 4x1 Modules or Mixtures or 8x1's, 4x1's, 2x1's and 2x2 Modules in Any Combination or Configuration up for up to 128 Relay Drives
CXM/128-MF
Chassis
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
Product
Speed Sensor
SP-TTL
-
Speed measured by counting teeth on a gear and dividing by n (where gear has n teeth).
-
Product
"Signal Transporter"
LTX-5525
-
The LTX-5525 conveys sixteen independent channels of digital information over a fibre optic link ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled 100 million times per second, multiplexed and transmitted serially over an optical fiber at two gigabits per second. The receiver acquires this digital data and de-multiplexes it to 16 separate output ports.
