TTL
Transistor–transistor logic.
-
Product
Serial Parallel Interface
Model 2303
-
* 2303 Board provides 40 high-power TTL I/O lines that can sink 23 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual Serial headers support conections with baud rate switch inputs or to a Serial Flat Ribon Cable Assembly. * Optional Relay Driver board drives 24-40 relays. * 114732 Board has the DIN connector on circuit side for use with the X3DVR Relay Driver Board or for piggyback mounting.* All other specifications are the same as listed above for the 2303.
-
Product
SP1T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave manufactures pin diode RF switches that are controlled by TTL logic. This configuration is known as single pole, single throw and is often abbreviated SPST or SP1T. They have been engineered to function in 50-ohm systems, and are designed to operate from 40 MHz to 18 GHz. They have a switching time of 100 nanoseconds and input power rating of 200 mW (23 dBm). Performance of 1.6:1 or better VSWR and minimum isolation of 60 dB is typical of most models.All switches of this type require both +5VDC and -5VDC to operate. Typical current consumption is +/- 30 mA. TTL control logic of 0 to +5VDC is required. Units comes standard with SMA connectors.
-
Product
IP-Parallel-IO
-
IP Compatible card with 48 programmable TTL IO or 24 - RS422 / RS485 compatible differential pairs. 5 mixed combinations available. Filtered or direct input. Programmable interrupt from each IO [TTL or differential]. 2 counter timers. Waveform generator.
-
Product
C012 Communication Board
MS 1728/29
-
- Suitable for standard desktops- Four channel in single board- Up to 10 Mbits/sec operating speed- Low Cost solution- Standard INMOS link protocol- Communicates with transputers- Converts between serial link and parallel bus- Tristate bidirectional bus interface- Memory mapped registers- Interrupt capability- TTL compatibility
-
Product
Crank Angle Measurement System
CP-5110B Detector/CA-6000B Amplifier
-
CP / CA series are systems that detect the rotation angle of the engine crankshaft composed of CP-5110B Fiber Optic Crank Angle Detector, CA-6000B Crank Angle Amplifier and CP-5120 / 5130 Slit disk.CP-5110B Fiber Optic Crank Angle Detector makes it possible to detect the crank angle required for various engine performance tests such as combustion analysis with high accuracy and high response. As it has a light projecting and receiving method with an optical fiber, it provides outstanding vibration and noise resistance without a built-in electric circuit in the detector.CA-6000B Crank Angle Amplifier inputs a signal of crank angle detector and outputs a TTL level angle signal and a 1P / R pulse signal.
-
Product
High-Frequency Switch
VCH-604
-
High-Frequency Switch VCH-604 is designed for switching high-frequency (1 – 100 MHz) and pulse TTL signals. VCH-604 contains two groups of channels; each group has 25 inputs and 2 outputs. VCH-604 can be controlled from PC via GPIB and RS-232 interfaces or directly from front panel.
-
Product
RS232 RS485 RS422 Serial To Ethernet Modbus Converters / Device Servers
-
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and flexibility. CommFront offers a range of industry-proven, easy-to-use serial to Ethernet converters and device servers, both hardware and software types. The applications of our serial to Ethernet converters include acting as a device server or a Modbus RTU/ASCII to Modbus TCP protocol converter; extending serial ( RS232 / RS485 / RS422 / TTL) communication distance over Ethernet network; controlling serial devices from remote Modbus TCP software or Modbus RTU master via Ethernet network; making a wide variety of M2M communication applications possible by enabling client access independent of any operating system or proprietary protocol; and converting conventional serial data network into TCP/IP network, etc.
-
Product
Digital Instruments
-
Digital Instruments generate and acquire high-speed digital waveforms for transmitting data, communicating with devices under test, or testing digital interfaces. These instruments are ideal for semiconductor characterization and production, interfacing to LVDS and TTL digital electronics, and testing the functionality of high-speed serial links.
-
Product
SP16T RF Pin Diode Switches To 10 GHz
-
Pulsar Microwave's 16-way switches cover 500 MHz to 10 GHz in single pole, 16-throw configuration. Maximum input power is 200 mW and switching time is 100 ns. SMA female connectors are standard. A 15-pin D-SUB male connector makes the internal connections to the power, ground and logic circuitry. Switching control is TTL with the option of line drivers and decoders.
-
-
Product
Ethernet To Parallel Digital Interface Boards
-
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
Product
RS232 / RS485 / RS422 To Fiber Optic Converters
-
Our rugged, industrial-grade, point-to-point RS232 / RS485 / RS422 serial to fiber optic converters work in pairs to extend serial signals (RS232, RS485, RS422, and TTL) over long distance. These point-to-point RS232 / RS485 / RS422 serial to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode (extend distance up to 3 miles / 5km) and single-mode (extend distance up to 25 miles / 40 km), and ST, SC, and FC connectors.
-
Product
PCI Data Acquisition Boards
ADDA12-100DMA Series - Dual 12-bit A/D + Dual 14-bit D/A, 25 Ms/s
-
Model ADDA12-100DMA has two simultaneously sampling 12-bit A/D converters, two 14-bit D/A converters, five vectored TTL inputs and two vectored TTL outputs, and is able to transfer data directly into the computer system's memory at 100 MB/s in systems with 64-bit PCI slots or 80 MB/s in 32-bit slots.
-
Product
PXI/PXIe Trigger-Module
PXT(e)1741
Trigger Module
Easy linkage of various external modules to the PXI(e) trigger busHigh configurable trigger matrix12 independent configurable trigger linesInputs/Outputs compatible with 5 V TTL standardSoftware controlled triggering of any target device
-
Product
USB-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA, USB Digital I/O Device
779975-01
Digital I/O
The USB-6509 is an industrial, bus-powered USB device that can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is … required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the USB-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
DFM (Deep and Fast Modulated) generators up to 280 GHz
-
Insight Product Company offers DFM (Deep and Fast Modulated) mm-wave sources at frequencies from 30 to 280 GHz. DFM generators are designed to go swiftly from the generation to the non-generation mode and back. This process controlled by the external TTL signal. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
Chassis - Controls up to 16 8x1 Modules, 32 4x1 Modules or Mixtures or 8x1's, 4x1's, 2x1's and 2x2 Modules in Any Combination or Configuration up for up to 128 Relay Drives
CXM/128-MF
Chassis
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
Product
NI-9403, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
779787-01
Digital Module
5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals.
-
Product
GPIB Parallel Interface
Model 4813
-
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Optional Relay Driver boards add 64 or 128 Relay Drivers.
-
Product
24 TTL Channels, Programmable I/O
TL1
-
Function module TL1 provides 24 channels of TTL/CMOS transceiver functionality as either inputs or outputs. The transistor-transistor logic (TTL) employs transmitters with multiple emitters in gates having more than one input. TTL offers high switching speed and relative immunity to noisy systems. CMOS sensors provide image sensing technology by converting light waves into signals that are small bursts of current. These waves can be light or other electromagnetic radiation.
-
Product
PCI 4-Input Frame Grabber
611
-
Color or monochrome: PAL, SECAM, NTSC, RS-170 compatible 4 composite video inputs or 3 composite and one S-video 8 TTL I/O lines for camera control Programmable AGC, hue, contrast, saturation Optional enhanced SDK for Windows 98/2000/NT/XP/CE Optional Linux and QNX drivers
-
Product
DUAL-IN-LINE (DIL/DIP) SERIES 97 - 98
-
Pickering’s dual-in-line (DIP/DIL) reed relays are through-hole electronic components that enclose two parallel rows of connection pins on the standard DIL spacing with switching capability up to 2 Amps, 50 Watts. The reed relays come with 5, 12 or 24 V coils with or without internal diode. Many standard build options are available on request, or we can fully customise the parts to suit your exact specifications.It is often possible to replace TTL ICs with their equivalent CMOS ones and replace standard DIL relays with Pickering Series 98, to obtain the benefits of CMOS without any circuit or PCB redesign.
-
Product
Dynamic Digital I/O (3U), 32 Channels Up To 200 MHz W/512MB On-Board Memory, W/LVDS
GX5283
Digital I/O
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
Switch
-
Chengdu KeyLink Microwave Technology Co., Ltd.
The power supply voltage of the series products are ±5V ± 5%，which using TTL control(default “0”：ON；"1"：OFF.).The frequency range covered by 0.5GHz~40GHz.The products have the characteristics of small size, high reliability, low insertion loss and high isolation.The products are applied to all kinds of receiving and transmitting channels. KeyLink's switches can be categorized as follows.
-
Product
synchro or resolver to digital (BCD) converters
AIT
Digital / Synchro Converter
Computer Conversions Corporation
The TSb series are miniature, high performance continuous tracking synchro or resolver to digital (BCD) converters and angle indicators employing a type 2 servo loop, designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input over a frequency range of 50 to 1200Hz. and convert it into 0 to 359.9 degrees or +/-179.9 degrees, TTL compatible BCD data.
-
Product
NI-6581, 100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module
780565-01
Digital I/O Adapter
100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module for FlexRIO—The NI-6581 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. You can use the NI-6581 to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581 can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
High-Capacity Compact Real-Time System
ADwin-Gold II
-
10 times more computing power than ADwin-Gold with the processor ADSP TS101S at 300 MHzMore memory: 768 kB CPU-internal RAM, 256 MB DRAMHigher resolution: 2 18 bit ADC with 8 analog inputs each via multiplexerFIFO memory at the digital inputs for fast detection of rising and falling edges with 100 MHz event counter2 analog outputs, 16 bit, 32 digital I/Os (TTL)
-
Product
32-CH DI & 32-CH DO 12 MB/s High-Speed Card
PCIe-7200
Digital I/O
- x1 lane PCI Express interface- 32-CH TTL digital inputs and 32-CH TTL digital outputs- Up to 12 MB/s transfer rate- Onboard programmable timer pacer clock- Support handshaking digital I/O transfer mode- Bus-mastering DMA for both digital inputs and outputs- 5 V power available on connectors- Compact, half-size PCB
-
Product
Optical Chopper
-
These high stability variable frequency optical choppers each include a set of chemically blackened photoetched chopping discs. The mini chopper is an excellent choice for applications requiring a compact package. The chopping discs come in a variety of slot apertures and allow operation. Beam diameter is limited to 0.75mm when using the 200-slot disc and 1.0mm when using the 40 slot mini disc. The easy-to-interchange blades are made of non-magnetic, half hard brass and can be used in combination. Chopping frequency is set by adjusting a ten-turn dial or by applying an external DC voltage to the BNC input. Reference output is a TTL pulse and is in-phase with chopping action. The 5 digit led display gives a direct read-out of the chopping frequency. Power: 90-130V or 180-260V; 50/60Hz; 12VA max. Power supply included. Choppers are often used together with lock-in amplifiers.
-
Product
Signal Conversion Box for Linear Gauge Sensor
DG-0010/0020
-
This is a signal conversion box to convert 2-phase signals (TTL) from the linear gauge sensor GS/BS series into open - collector (DG-0010) or line driver (DG-0020) .This conversion box allows direct connection with the PLC *. It can also be transmitted over long distances.
