RS-422
One of several standards that incorporate balanced line signals into DB connectors. A pair of wires is used to carry each signal. The data is encoded and decoded as a differential voltage between the two lines. (www.sangoma.com)
-
Product
Serial I/O Expansion
PCM-G-COM8
-
The PCM-G-COM8 is an 8-channel PC/104-compatible serial module. It is well suited for embedded applications requiring a large number of serial I/O ports. Each channel supports RS-232, RS-485, and RS-422 electrical levels to interface to a wide variety of serial communications devices such as modems, data collection equipment, and distributed I/O terminals. The PCM-COM8 will operate over the full industrial temperature range of -40° to +85° Celsius.
-
Product
Surface And Subsurface EW System Tester
MS 1119
-
CPCI Based BTA is used to test ECM System Processor (80386 & 8051) Boards. This system consists of a Single Board Computer (SBC), CPCI RS422 Communication and Bus Interface Board (CBI), CPCI Digital Input & Output (DIO) Board and CPCI Analog Input & Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
Product
Electronic Controllers
-
CAES designs and manufactures stepper and brushless DC controllers for aerospace applications. A variety of interfaces (1553, RS422), input voltages, and drive schemes are available. Custom requirements are welcomed.
-
Product
RS-232 to RS-422/RS-485 Optically Isolated Interface Converter
Model 245
-
Total Isolation; Selectable RS-422 or RS-485; Selectable 2 or 4 wire RS-485; Intelligent Control of RS-485; TD & RD LED's on Each Side of Opto Barrier; Data Rates up to 128 KBPS. The Model 245 RS-232 to RS-422/RS-485 Optically Isolated Interface Converter is an optically isolated version of the Model 285.
-
Product
96 Channel I/O and 64 Channel I/P VME Module
DP-VME-3132
-
The DP-VME-3132 provides 96 channel RS422 differential digital I/Os and 64 channel RS422 differential isolated inputs on the front end and rear side. On the rear side, it is interfaced with the VME 64x backplane.
-
Product
Low Profile PCI Express 2-Port RS-232, RS-422, RS-485 Serial Interface
7205e
-
The 7205e low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port utilizes a 16C950 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the 14.7456 oscillator and UART’s flexible clock prescalar supports the widest range of standard and non-standard baud rates.
-
Product
8-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V/5V
APCI-7800-3
-
8-port serial interface, RS232, RS422, RS485, 20 mA CL, modular mounting
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 2 9-Pin Female D-Subs, for RS-422/485
540041010101
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 2 9-Pin Female D-Subs
-
Product
MODEM ELIMINATOR
-
The UDC-ME allows two DTE devices (such as routers) to communicate within proximity of each other. The UDC-ME transmits data bi-directionally at clock rates of 1.2k up to 3.072Mbps between DTE devices. The unit is equipped with two interface slots that allow a host of serial interface cards to be utilized. The serial interface cards available are RS-232, RS-422/449, RS-530, X.21, V.35 and HSSI. The Serial Interface cards are interchangeable and may be mixed such as RS-232 to V.35 thus eliminating the need for an interface converter or changing expensive serial cards on a DTE device such as a router.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-104
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Interface And Signal Processing Units
-
The interface and signal processing units extend the field of application of Micro-Epsilon sensors. The interface modules are used to convert sensor signals into digital or bus-compatible interfaces. This enables interfaces such as USB, RS422, Ethernet/IP, Profinet and EtherCAT for numerous sensors. The signal processing units are also used to record several sensor signals, to calculate and output them together. This is necessary, for example, for planarity measurement or thickness measurement.
-
Product
CPCI Based 486DX4 Board
MS 1501
-
- CPCI/PXI Bus Interface, 6U form factor- Watchdog Timer- Hot Swap Facility- PCI Bus Rear IO Expansion for External Bus Interface- Debugging Monitor interface through RS232- JTAG interface for 486 for boundary scan test- Power Source through the CPCI connector J1 (±12V, +5V, 3.3V)- 1Mbytes of Dual Port RAM, 256Kbytes of STATIC RAM- 1MBytes of FLASH PROM- RS232, RS422 Serial Interface- Intel 486DX4 operating at 100MHz frequency at the core- Driver interface for Windows2000/XP/VISTA and LINUX/RT LINUX OS
-
Product
RS232 / RS485 / RS422 To Fiber Optic Converters
-
Our rugged, industrial-grade, point-to-point RS232 / RS485 / RS422 serial to fiber optic converters work in pairs to extend serial signals (RS232, RS485, RS422, and TTL) over long distance. These point-to-point RS232 / RS485 / RS422 serial to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode (extend distance up to 3 miles / 5km) and single-mode (extend distance up to 25 miles / 40 km), and ST, SC, and FC connectors.
-
Product
RS-232 to RS-422 Interface Converter
Model 253
-
FEATURES: DB9 Data Port; Compatible with PC/386/486; Full Duplex; Surge Protection. Adding an RS-422 interface to a PC is now a snap. The Model 253 Interface Converter does this for full duplex signals at data rates up to 19.2 KBPS, without requiring any AC or DC power. With only TD, RD and ground, the Model 253 provides operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
Product
IDoor Module: 4-Ports Non-Isolated RS-422/485 MPCIe, DB37
PCM-24D4R4
Expansion Module
Meets Advantech Standard iDoor TechnologyPCI Express® Mini Card Specification Revision 1.2 compliantSpeeds up to 921.6 kbps for extremely fast data transmissionSupports any baud rate setting (50bps~921.6kbps)Supports both Isolated & Non-Isolated Protection with 2/4 Ports RS-232/422/485I/O address automatically assigned by PCIe plug & playOperating systems supported: Windows 2000/XP/Vista/7, and Linux 2.4/2.6Supports Embedded Automation PC UNO-2200/2300/2400 seriesSupports Control DIN-Rail PC UNO-1200/1300/1400 seriesSupports Control Cabinet PC UNO-3200/3300/3400 seriesSupports Control Panel Computers TPC-xx81/xx82 seriesSupports Thin Client Panel Computers TPC-xx51 series
-
Product
Isolated RS-485
-
Analog Devices offers a wide range of standard RS-485/RS-422 transceivers and iCoupler® isolated RS-485/RS-422 transceivers to suit many applications. The RS-485 specification meets the requirements for a truly multipoint communications network, and the standard specifies up to 32 drivers and 32 receivers on a single (2-wire) bus. Some RS-485 transceivers modify the input impedance to allow up to 8× more nodes to be connected to the same bus.
-
Product
Mezzanine System
5033
System
ECM P/N 5033 provides eight channels of RS485 / RS422 I/O. The 110 ohm termination for each channel is enabled or disabled in software. Disabling termination saves power by eliminating unneeded or redundant termination. Speeds of up to 20 Mega bits per second are possible, but this design also features a 250K bits per second slower edge rate mode. The 250K bit mode is valuable when EMI is more of a concern and throughput is not important. All channels power up as inputs with the outputs disabled.
-
Product
Sixteen Port MIL-STD-1760E/HS-1760 Lab Switch
SWT-HS1760-16
-
Avionics Interface Technologies
AS5653B Compliant switch - Sixteen port non‐blocking switch with each port operational at 1.0625 Gbps - Crossbar design, with 34 Gbps total transmit and receive bandwidth - Controlled via RS-232/RS-422/RS-485 or SSH/SFTP over Ethernet - Monitor/Keyboard via VGA and USB ports - FPGA based design - Available as IP CORE
-
Product
Serial Transceivers
-
Exar offers a complete portfolio of RS-232, RS-485 and RS-422 transceivers and the industry's largest portfolio of multiprotocol transceivers. At 52Mbps, Exar offers some of the industry's fastest RS-485 and multiprotocol transceivers.
-
Product
Smart GPIB Serial Interface Board
Model 4808
-
* Provides smart GPIB-to-serial path for serial devices with RS-232, RS-422 or RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Rear panel mounting eliminates cables.
-
Product
GPIB Serial Interface
Model 4894B
-
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Expanded baud rate range from 50 to 115,200 baud.* 256 Kbyte RAM buffer for spooling data.* Over 600 Kbyte/second GPIB data transfer rate.*Transparent data transfer.* Programmable replacement for the NI CV interfaces.* 1 U high rack mount kit mounts one or two 4894Bs* Includes US 115 VAC Power Adapter, Manual and Support CD.
-
Product
3U CPCI ARINC 429 Board
MS 1725
-
- Bus Interface:- 32 Bit PCI Bus with 3 U Form factor- PCI to PCI Bridge Interface- Speed of operation up to 66MHz- 8 ARINC 429 TX and 16 ARINC 429 RX channels- 4 RS422 Channels- 16 TTL I/O Channels- Message Storage Buffer- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Product
Multi Protocol Analyzer
LE-3500R
-
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
Product
PXI-8433, 2-Port, Isolated, RS485/RS422 PXI Serial Interface Module
779744-01
Serial Interface
2-Port, Isolated, RS485/RS422 PXI Serial Interface Module - The PXI‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCIe-8431, PCI Express, 16-Port, RS485/RS422 Serial Interface Device
780592-02
Serial Interface
The PCIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
GPIB-RS485/RS422 GPIB Instrument Control Device
779733-02
GPIB Controller
Serial, RS485/RS422 GPIB Instrument Control Device - The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Analog or Digital Communications Switching Systems with D Type Connectors
RS Series
-
The RS Series computer controlled switching systems are designed to switch multi-wire groups of signal up to 25 wires. These systems are typically used for signals such as parallel TTL, RS232, RS422, WAN or modems, but can also be used for any group of analog or digital signals having a bandpass up to 30 MHz or a data rate up to 20 Mbps.
-
Product
Firmware for High-speed Communication
OP-FW12GA
-
OP-FW12GA is the firmware to increase the speed of monitoring test of bit synchronous communication (such as HDLC/SDLC/X.25, or CC-Link communication), SPI communication, Profibus-DP (field bus known for high-speed communication), UART (asynchronous communication, which is commonly used). By processing great part of monitoring processes by FPGA, it unfailingly captures communication data with time stamps of a microsecond rate. The interface supports RS-232C/RS-422/RS-485/TTL.
-
Product
1-Ch TTL/RS-422 Incremental Encoder/Counter EtherCAT Slice IO Module
AMAX-5081
EtherCAT Slice IO Module
Overflow/underflow detectionLatch counter valueReset counter valueSet counter valueInput filterPosition compare outputReversion of A/B phase InputFrequency measurement (Pulse Input)
-
Product
RS422 Mode SI-module With Optical Isolation
MX422-G
-
RS422 mode SI-module with optical isolation
