kV
A thousand volts of electromotive force.
-
Product
HIPOTS (High Voltage Testers) / AC Hipots
5 kV Digital
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Panel mounted controls & indicators. Variable from zero to 5 kV. Digital kV and leakage mA meter.
-
Product
Cable Test Van
BAUR Transcable 4000/S 70-3
-
Transcable 4000/S 70-3. The transcable 4000 70 kV 3/S cable test van varies in comparison with the transcable 32 kV - 3S in the 70 kV voltage level. The system is controlled with the MGS semi-automatic control unit. The high voltage switch unit is 3-phase, air and solid matter insulated and safe to touch.
-
Product
Microprocessor Multifunction TRMS Power Meter + Harmonics Analyzer
8100 C
-
Kusam Electrical Industries Limited
INPUT :• Input Voltage Range :Voltage: 55 ~ 300V AC, or 300 ~ 600V AC, 45 ~ 65Hz.P.T. Ratio Programmable upto 9999 / KV.• Input Voltage Over Range :Voltage : 200 % Continuous, 300 % of rating for 10 sec.• Input Current Range :Current : 110 % of rating. 0-1A or 0 - 5AC.T. Ratio programmable upto 9999 / 5A.Input Current Over Range:Current : 400 % Continuous, 2000 % of rating for 10 Sec.• Input Frequency : 45 Hz ~ 70 Hz.• Input Burden :Voltage 0.25 VA / Unit, Current 0.25VA / Unit, at 50 / 60HzOUTPUTDC Current: 0 20 m A DCLoad resistance drive: output drive 10 V DC maximum.DC Voltage: 0 -10 V DCLoad resistance drive: output drive 5mA maximumOutput Protection: No damage even if output is Open or Short Circuit.Output Response Time : £ 1 Sec.Digital Output : RS485 Output, Isolate Type with MODBUS RTU mode., 4800, 9600,19200Baud Rate, User Selectable.
-
Product
HIGH VOLTAGE MEGOHMMETER
MI-15KVe
-
The MI-15KVe High-Voltage Megohmmeter is a truly portable device that allows the measurement of insulation resistances using test voltages up to 15 kV. It employs a state-of-the-art technology for the safe measurements of insulation resistances up to 3.000.000 MΩ with four test voltages: 1 kV - 5 kV - 10 kV and 15 kV.
-
Product
ULI-344DC - USB To RS-232/422/485 (DB9 Male) Industrial Isolated Converter, 4 Port
BB-USR604
USB HUB
USB to RS-R32/422/485 ConverterUL Class 1/Division 22 kV IsolationLevel 4 ESD Protection (15 kV Air, 8 kV Contact)921.6 Kbps Serial Data Rate- 40 to + 80 °C Operating TemperatureDIN and Flat Panel Mounting OptionsTB and Power Jack 10-30 VDC Power InputsHigh Retention USB Connector, Plug in Serial Terminal Block
-
Product
HIGH VOLTAGE MEGOHMMETER
MI-10KVe
-
The MI-10KVe High-Voltage Megohmmeter is a truly portable device that allows the measurement of insulation resistances using test voltages up to 10 kV. It employs a state-of-the-art technology for the safe measurements of insulation resistances up to 2.000.000 MΩ with four test voltages: 1 kV - 2 kV - 5 kV and 10 kV.
-
Product
XRT Source Brighthawk
-
The BRIGHTHAWK NT100 is a performance-leading microfocus X-ray tube comprising proprietary technology to achieve a high brightness output. The tube consists of a LaB6 crystal source for generation of the electron beam, a magnetic beam steering system, and a tungsten target for X-ray photon emission. The components are mounted in a precision-engineering housing and held at ultra-low vacuum levels for long-life performance. Following on from the successful 3rd generation tube, this 4th generation of tube across a wide energy range from 30 kV to 160 kV is highly configurable through a software interface to the internal control board, which is connected via an optical interface (through an Ethernet converter).
-
Product
Bench Digital Multimeter, Calibrated, 1 kV, 10 A, 3.8 Digit
72-1015 CAL
-
The 72-1015 CAL from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
Product
Aerial Lift Testers
ALT Series
-
HVI produces AC voltage testers that perform boom and liner testing, with models available up to 300 kV AC for boom testing and 10 kVA for liner testing. The ALT Series is designed for AC voltage testing aerial lift devices. The standard models available are rated 120/60 kV AC, 200 kV AC, and 300 kV AC, rated up to 7 kVA.
-
Product
High-Voltage Test and Diagnostics Device
Viola
-
Cable testing and diagnostics with the BAUR viola. The portable and powerful viola high-voltage testing and diagnostics device is used for cable and cable sheath testing of medium-voltage cables up to 35 kV and electrical equipment. Another function is insulation testing on electrical equipment.* High performance and compact* Precise and non-destructive determination of the cable condition* Easy and quick test setup* Automatic testing and diagnostic sequences
-
Product
Contact Resistance Meter
CRM 200B+
-
CRM directly measures micro-ohm values at 200A DC under live EHV switchyard conditions quickly & accurately. It is specially designed to reliably measure micro-ohm contact resistances of Circuit Breakers, Isolators, Busbar joints, earth switch joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards up-to 765 kV. SCOPE’s ability to make electronics work in such environment enables CRM to measure mili-volts signal in the presence of kilo-volts noise.
-
Product
RS-422 RS-423 RS-485
-
The low-power, high-speed transceivers of this family are designed for RS-485, RS-422 and RS-423 communication applications. They usually contain one driver and one receiver in half duplex configuration. Each driver output and receiver input is protected against electrostatic discharge up to ± 15 kV and has no latch-up. These transceivers operate with a 5 V supply and draw a very low supply current when unloaded or fully loaded but with disabled drivers.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 1 kV Isolation
41-752A-111
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
High-Voltage Test Device
PGK 150 / 5 HB
-
Cable testing and diagnostics with the BAUR PGK H. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 150 kV output voltage with positive or negative polarity* AC voltage testing - up to 110 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
Product
High Voltage Test Set
Hi-Pot Series
-
SCOPE introduces a high voltage test set, these high voltage testing sets comes with Power frequency AC high voltage /DC high Voltage test /AC-DC high Voltage test set for testing transformers, motors, insulators, cables etc. Further, these testing sets are capable of giving continuously variable HIGH VOLTAGE from zero to maximum rated output voltage. Wide range of up to 100 kV is available in user selectable combinations.
-
Product
Pil Dielectric Test Sets
DTS Series
-
The DTS Series provides repeatable and accurate measurements of the breakdown voltage of insulating oils used in electrical equipment. The DTS-60D & DTS-100D offer 60 kV AC and 100 kV AC output respectively. They include three user-selectable, automatic voltage rates-of-rise, and automatic voltage shutdown with the meter indicating the flashover voltage. Various test cells are available.
-
Product
Industrial 4-Port Modbus Gateway
EKI-1224
-
Supports surge protection for D.C. power ports with line to line 2 KV, and line to earth 4 KV; for signal ports with 4 KV. Provides 2 x 10/100 Mbps Ethernet ports for LAN redundancy. Integration of Modbus TCP and Modbus RTU/ASCII networks.
-
Product
Insulation Resistance Measurement
MD 15KVR
-
The digital insulation tester model MD-15KVR is Megabras' cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A powerful software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 15 TΩ, with 4 pre-selected test voltages, 500 V - 5 kV - 10 kV - 15 kV. Other test voltages may be selected in steps of 25 V, 100 V or 500 V.
-
Product
5 kV Electric Motor Analyzer
MCE
-
The MCE is the most comprehensive static electric motor test equipment available on the market today. Through a series of powerful diagnostic tests, the MCE provides a complete look at the health of an offline motor. The MCE provides critical information to technicians allowing them to diagnose problems early, thus reducing unwanted downtime.
-
Product
NO LOAD & LOAD TEST BENCH
-
International Biological Laboratories
These are the test benches incorporating control & measurement circuitry necessary for testing single phase as well as three phase transformers of several VA to MVA rating & voltage class of 11KV/433V,as well 33KV/11 KV, after manufacturing, repairing, reconditioning. Following tests can be done by these Test Sets.
-
Product
Test and Analysis
-
ESDEMC Technology will calibrate; the Contact Mode ESD current waveform and tip voltage to 4 GHz and 30 kV, the frequency response of ESD Target & Adapter Line to 4 GHz, and the DC Resistance
-
Product
ELECTRONIC MEGOHMMETER
MI-2550e
-
The MI-2550e general purposes megohmmeter is a truly portable equipment suitable to measure insulation resistances using test voltages up to 2,5 kV. It employs high-reliable, state-of-the-art technology for accurate measurements of ultra high insulation resistances up to 5.000.000 MΩ with four test voltages: 0,5 kV - 1 kV - 1,5 kV - 2,5 kV.
-
Product
Insulation Tester
1555
-
The Fluke 1555 insulation resistance tester offers digital insulation testing up to 10 kV, making it ideal for testing high voltage equipment including switchgear, motors, generators and cables.
-
Product
EBSD Detector
Symmetry
-
Electron backscatter diffraction – is a powerful microanalysis technique that enables rigorous characterisation of the micro structural properties of crystalline materials. A high performance EBSD detector is critical for the effectiveness of the technique, influencing both speed and data quality. Symetry is Over 3000 indexed patterns per second (pps). Up to 30x faster than existing CCD-based detectors. Extreme sensitivity for low current and low kV analyses. Megapixel resolution for HR-EBSD applications. High resolution patterns (at least 156 x 128 pixels) at all speeds.
-
Product
DC High-Voltage Test Device
PGK 80
-
Cable testing and diagnostics with the BAUR PGK 80. The portable, one-piece PGK 80 high-voltage test device for generating negative DC voltage up to 80 kV is primarily used for onsite testing of paper-insulated mass-impregnated cables in the medium-voltage network. The high voltage is generated through a high-voltage transformer with secondary voltage-multiplier. The internal operating frequency of 20 kHz enables the smallest of device dimensions.* Continuous adjustable output voltage* The voltage measurement is done directly at the high voltage output* Timer of 1-30 min* Sensitive current measurement for recording the smallest of insulation currents with 6-time range switch, decadal
-
Product
Hipot Instruments
HypotMAX® Series
-
Our HypotMAX series is a complete Line of automated Hipot instruments designed to meet the demanding requirements of high voltage applications. We've included our patented SmartGFI feature of maximum operator safety protection as well as a variety of advanced features to increase productivity. Setup and run tests up to 20 kV with confidence from our intuitive user interface or automate with PC.
-
Product
2-Port RS-232/422/485 Serial Device Server
EKI-1522
-
Provides 2 x 10/100 Mbps Ethernet ports for LAN redundancyProvides COM port redirection (Virtual COM), TCP and UDP operation modesSupports up to 921.6 kbps, and any baud rate settingAllows a max. of 5 hosts to access one serial portAllows a max. of 16 hosts to be accessed as TCP client modeBuilt-in 15 KV ESD protection for all serial signalsProvides rich configuration methods including Windows utility, Telnet console, and Web BrowserSupports 32-bit/64-bit Windows 2000/XP/Vista/7/8/8.1/10, Windows Server2003/2008/2012/2016, and LinuxAutomatic RS-485 data flow controlSupports line to line 2 KV, line to ground 4 KV surge protection
-
Product
Surge Voltage Generator
SSG 1500
-
Cable fault location with the BAUR SSG 1500. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
Product
High Voltage 50 Ω Pulse Generator
TLP-4010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
Product
Digital Panel Meter
-
Nippen Electrical Instruments Co.
To be supplied with the right meter, simply furnish the following details in your order: Model Number, Description of the Meter. Accuracy Class. Voltage Input (110 Volts from PT, 240 Volts line to neutral or 415 Volts Line to Line). PT Ratio specifies the High Voltage Primary first ( 33 kV.110V). Current input (5Amps or 1 Amp secondary ) CT ratio (e.g. 100/5 Amps. etc.). Aux. Supply : 50/60 Hz (240VAC of 110/VAC). Dimension : 96 x 96mm or 48 x 96 mm or 144 x 144 mm.
