Digital Fault Recorders
record out of limit electrical power system events.
See Also: Fault Recorders, Transient Recorders, Disturbance Recorders
-
Product
Digitizer Adapter Module For FlexRIO
Digitizer
Digitizer Adapter Modules for FlexRIO can be used with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO to create a high‐performance instrument with customizable firmware. With sampling rates from 40 MS/s to 3 GS/s and up to 32 channels, these modules cover a wide range of requirements for both time- and frequency‐domain applications. Digitizer adapter modules also provide digital I/O capability for interfacing with external hardware.
-
Product
Digital I/O Board
3512
Digital I/O
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
Product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785648-02
FlexRio Digitizer
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset.
-
Product
PCI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Output, Bank-Isolated Digital I/O Device
778835-01
Digital I/O
The PCI-6515 is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 20 Channels, 20 Single-Ended Inputs
DN6.445-20
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
64-Channel Boundary Scan Digital I/O Scan Module
JT 2111/MPV DIOS DIN
Digital I/O
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.This JT2111/MPV DIOS module is also available through our webshop.
-
Product
Dual-Channel 12-Bit, 1 GSPS Digitizer
ADQ33
Digitizer
ADQ33 offers a two channel configuration with 1 GSPS sampling rate. The programmable DC-offset makes it ideal for sampling unipolar signals.
-
Product
PXI Digital Pattern Instrument
Digital Pattern
The PXI Digital Pattern Instrument is designed for semiconductor characterization and production test. It provides 32 channels, a voltage range of -2 V to 6 V, a PPMU force voltage range of -2 V to 7 V, up to a 200 Mb/s data rate, and a clock generation rate up to 160 MHz. The module includes Digital Pattern Editor software as well as debugging tools like shmoo, digital scope, viewers for history RAM, pin states, and system status.
-
Product
PXI Semi-Dynamic Digital I/O Module, 32-Channel
40-419-003
Digital I/O
The 40-419-003 is a 32-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
FPGA PXIe High-Performance Digital I/O Card
GX3700e
Digital I/O
The GX3700e is a user configurable, FPGA–based, 3U PXI Express card offering 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features over 45,000 logic elements and 1.836 Kb of memory. The GX3700e is supplied with an integral expansion board providing access to the FPGA’s 160 I/Os. Alternatively, users can design their own custom expansion cards for specific applications - eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system. The design of the FPGA is done by using Altera’s free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded directly into the FPGA or via an on-board EEPROM.
-
Product
NI-9375, 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-02
Digital Module
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
Product
PXI/PXIe Fault Insertion Switch, 32-Chan 2A, N/C Through Relays, Fault Buses on M & U
42-190C-212
Fault Insertion Unit
The 40-190C-212 (PXI) and 42-190C-212 (PXIe) are fault insertion switches with 32 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785162-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Razor Express 16XX CompuScope 16-Bit, 200 MS/s, PCIe Digitizer / Oscilloscope
Digitizer
The GaGe Razor Express16XX CompuScope PCIe digitizer board features 16-bit resolution with sampling rates up to 200 MS/s with true Effective Number of Bits (ENOB) of 11.7-bits with 10 MHz input.
-
Product
Multifunction Module for 34970A/34972A
34907A
Digital I/O Module
The Keysight 34907A module for the 34970A/34972A Data Acquisition/Switch Unit allows great flexibility for a variety of sense and control applications. It combines two 8-bit ports of digital input and output, a 100 kHz gated totalizer, and two 12V analog outputs - all on a single earth-referenced module. The digital inputs and totalizer input may be included in a scan. Alarm limits for the digital and event counter inputs are evaluated continuously, capturing and logging alarm conditions even between scans.
-
Product
Dynamic Digital I/O with Per Channel Programmable Logic Levels and PMU PXI Card
GX5295
Digital I/O
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
Product
Single Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-001
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.593-04
Digitizer
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 500 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.825-02
Digitizer
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
Passive Probe Interface Adapter
CX1151A
Digital I/O Adapter
The CX1151A is an adapter for passive probes for the voltage waveform measurements by the CX3300 series Device Current Waveform Analyzer.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
DN2.222-02
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 6-Channel
42-203-002
Fault Insertion Unit
The 40-203-002 (PXI) and 42-203-002 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 6 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
Digital Input Board
VME-1128
Digital Input Board
VME-1128 is a 128-bit High-Voltage Digital Input Board with Built-in-Test. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297) with the following mnemonics: A24:A16:D32/D16/D08 (EO): Slave: 39/3D:29/2D Form factor: 6U
-
Product
PCIe 12-Bit, 6 GS/s, Gen3 Digitizer
EON Express CompuScope
Digitizer
The GaGe EON Express CompuScope PCIe Gen3 digitizer board features unprecedented speed and resolution in a 6 GS/s streaming digitizer with 1.75 GHz bandwidth and PCIe data streaming rates up to 6 GB/s.
-
Product
68-Pin VHDCI Male to 68-Pin VHDCI Male, 50 Ω, Shielded Digital Cable
196275-01
Digital Cable
The SHC68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
Product
6U PXI Multi-Channel Analog I/O PXI Card
GX3348 Series
Digital I/O
The GX3348 is a multi-channel analog I/O 6U PXI card which provides (3) programmable sources, a ground source connection, a pulse / square wave generator (A version only) and a 4 x 48 or 4 x 64 matrix - allowing the user to route the 3 sources, or ground to any of the 48 or 64 I/O channels. In addition, each I/O channel can be connected to a 16-bit A to D converter, providing DC voltage measurement capability for each channel. The module also offers (8) static digital I/O for controlling / monitoring a UUT's digital signals.
-
Product
PXIe 16 Bit High Speed Digitizer - 250 MS/s on 4 Channels
M4X.4421-X4
Digitizer
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5962-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
100 MHz 32-CH High-Speed Digital I/O Card
PCIe-7360
Digital I/O Module
ADLINK's PCIe-7360 is a high-speed digital I/O board with 32-CH bi-directional parallel I/O lines. Data rate up to 400 MB/s is available through the x4 PCI Express® interface. Clock rate can support up to 100 MHz internal clock or 200 MHz external clock, ideally suiting applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
Product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785650-01
FlexRio Digitizer
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset.
